Search NASA⌕ Search

Engineering topics

Li, D.

Publications and source records attributed to Li, D..

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2012

Effect of twinning on texture evolution of depleted uranium using a viscoplastic self-consistent model

Ductility and fracture toughness is a major stumbling block in using depleted uranium as a structural material. The ability to correctly model deformation of uranium can be used to create process path methods to improve its structural design ability. The textural evolution of depleted uranium was simulated using a visco-plastic self consistent model and analyzed by comparing pole figures of the simulations and experimental samples. Depleted uranium has the same structure as alpha uranium, which is an orthorhombic phase of uranium. Both deformation slip and twin systems were compared. The VPSC model was chosen to simulate this material because the model encompasses both low-symmetry materials as well as twinning in materials. This is of particular interest since depleted uranium has a high propensity for twinning, which dominates deformation and texture evolution. Simulated results were compared to experimental results to measure the validity of the model. One specific twin system, the {l_brace}176{r_brace}[512] twin, was of specific notice. The VPSC model was used to simulate the influence of this twin on depleted uranium and was compared with a mechanically shocked depleted uranium sample. Under high strain rate shock deformation conditions, the {l_brace}176{r_brace}[512] twin system appears to be a dominant deformation system. By simulating a compression process using the VPSC model with the {l_brace}176{r_brace}[512] twin as the dominant deformation mode, a favorable comparison could be made between the experimental and simulated textures. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2012

Progress on a Cavity with Beryllium Walls for Muon Ionization Cooling Channel R&D.

The Muon Accelerator Program (MAP) collaboration is working to develop an ionization cooling channel for muon beams. An ionization cooling channel requires the operation of high-gradient, normal-conducting RF cavities in multi-Tesla solenoidal magnetic fields. However, experiments conducted at Fermilab?s MuCool Test Area (MTA) show that increasing the solenoidal field strength reduces the maximum achievable cavity gradient. This gradient limit is characterized by an RF breakdown process that has caused significant damage to copper cavity interiors. The damage may be caused by field-emitted electrons, focused by the solenoidal magnetic field onto small areas of the inner cavity surface. Local heating may then induce material fatigue and surface damage. Fabricating a cavity with beryllium walls would mitigate this damage due to beryllium?s low density, low thermal expansion, and high electrical and thermal conductivity. We address the design and fabrication of a pillbox RF cavity with beryllium walls, in order to evaluate the performance of high-gradient cavities in strong magnetic fields.

43 PARTICLE ACCELERATORS↗
DOE OSTI2012

Progress of MICE RFCC Module

Recent progress on the design and fabrication of the RFCC (RF and superconducting Coupling Coil) module for the international MICE (Muon Ionization Cooling Experiment) are reported. The MICE ionization cooling channel has two RFCC modules, each having four 201- MHz normal conducting RF cavities surrounded by one superconducting coupling coil (solenoid) magnet. The magnet is designed to be cooled by three cryocoolers. Fabrication of the RF cavities is complete; preparation for the cavity electro-polishing, low power RF measurements, and tuning are in progress at Lawrence Berkeley National Laboratory (LBNL). Fabrication of the cold mass of the first coupling coil magnet has been completed in China and the cold mass arrived at LBNL in late 2011. Preparations for testing the cold mass are currently under way at Fermilab. Plans for the RFCC module assembly and integration are being developed and are described.

43 PARTICLE ACCELERATORS↗
DOE OSTI2012

Design and Analysis of the PXIE CW Radio-frequency Quadrupole (RFQ)

The Project X Injector Experiment (PXIE) will be a prototype front end of the Project X accelerator proposed by Fermilab. PXIE will consist of an H- ion source, a low-energy beam transport (LEBT), a radio-frequency quadrupole (RFQ) accelerator , a medium-energy beam transport (MEBT) and a section of superconducting cryomodules that will accelerate the beam from 30 keV to 30 MeV. LBNL has developed an RFQ design for PXIE with fabrication scheduled to begin before the end of CY 2012. The chosen b aseline design is a four-vane, 4.4 m long CW RFQ with a resonant frequency at 162.5 MHz (2.4 wavelengths long). The RFQ will provide bunching and acceleration of a nominal 5 mA H- beam to 2.1 MeV. The relatively low wall power density results in wall powe r losses that are less than 100 kW. The beam dynamics design has been optimized to allow for more than 99% beam capture with exceptionally low longitudinal emittance. The RFQ mechanical design and the results of RF and thermal analyses are presented here.

43 PARTICLE ACCELERATORS↗
DOE OSTI2012

Kinetic Modeling of RF Breakdown in High-Pressure Gas-filled Cavities

Recent studies have shown that high gradients can be achieved quickly in high-pressure gas-filled cavities without the need for long conditioning times, because the dense gas can dramatically reduce dark currents and multipacting. In this proj ect we use this high pressure technique to suppress effects of residual vacuum and geometry found in evacuated cavities to isolate and study the role of the metallic surfaces in RF cavity breakdown as a function of radiofrequency and surface preparation. A series of experiments at 805 MHz using hydrogen fill pressures up to 0.01 g/cm3 of H2 have demonstrated high electric field gradients and scaling with the DC Paschen law limit, up to ~30 MV/m, depending on the choice of electrode material. For higher fi eld stresses, the breakdown characteristics deviate from the Paschen law scaling. Fully-kinetic 0D collisional particle-in-cell (PIC) simulations give breakdown characteristics in H2 and H2/SF6 mixtures in good agreement with the 805 MHz experimental resu lts below this field stress threshold. The impact of these results on gas-filled RF accelerating cavity design will be discussed.

43 PARTICLE ACCELERATORS↗
NASA NTRS2011

An All Silicon Feedhorn-Coupled Focal Plane for Cosmic Microwave Background Polarimetry

Upcoming experiments aim to produce high fidelity polarization maps of the cosmic microwave background. To achieve the required sensitivity, we are developing monolithic, feedhorn-coupled transition edge sensor polarimeter arrays operating at 150 GHz. We describe this focal plane architecture and the current status of this technology, focusing on single-pixel polarimeters being deployed on the Atacama B-mode Search (ABS) and an 84-pixel demonstration feedhorn array backed by four 10-pixel polarimeter arrays. The feedhorn array exhibits symmetric beams, cross-polar response less than -23 dB and excellent uniformity across the array. Monolithic polarimeter arrays, including arrays of silicon feedhorns, will be used in the Atacama Cosmology Telescope Polarimeter (ACTPol) and the South Pole Telescope Polarimeter (SPTpol) and have been proposed for upcoming balloon-borne instruments.

Hubmayr, J.↗
DOE OSTI2011

Research and Development of H Ion Source and LEBT for a Kaon-neutrino Factory

A baseline H{sup -} ion source and low energy beam transport system (LEBT) have been identified for Project X. The filament-discharge H{sup -} ion source has been fabricated by D-Pace, Inc. and is now in operation at LBNL. The source is capable of delivering over 10mA of H{sup -} beam in cw operation with normalized 4rms emittances less than 0.7 {pi} mm mrad. A two-solenoid magnetic lens LEBT system has been design. The design has been validated with simulations of beam transport for 5 mA 30 keV H- beams using various simulation codes.

43 PARTICLE ACCELERATORS↗
NASA NTRS2005

Electrochemical Impedance Spectroscopy of Alloys in a Simulated Space Shuttle Launch Environment

Corrosion studies began at NASA/Kennedy Space Center in 1966 during the Gemini/Apollo Programs with the evaluation of long-term protective coatings for the atmospheric protection of carbon steel. An outdoor exposure facility on the beach near the launch pad was established for this purpose at that time. The site has provided over 35 years of technical information on the evaluation of the long-term corrosion performance of many materials and coatings as well as on maintenance procedures. Results from these evaluations have helped NASA find new materials and processes that increase the safety and reliability of our flight hardware, launch structures, and ground support equipment. The launch environment at the Kennedy Space Center (KSC) is extremely corrosive due to the combination of ocean salt spray, heat, humidity, and sunlight. With the introduction of the Space Shuttle in 1981, the already highly corrosive conditions at the launch pad were rendered even more severe by the acidic exhaust from the solid rocket boosters. Over the years, many materials have been evaluated for their corrosion performance under conditions similar to those found at the launch pads. These studies have typically included atmospheric exposure and evaluation with conventional electrochemical methods such as open circuit potential (OCP) measurements, polarization techniques, and electrochemical impedance spectroscopy (EIS). The atmosphere at the Space Shuttle launch site is aggressive to most metals and causes severe pitting in many of the common stainless steel alloys such as type 304L stainless steel (304L SS). A study was undertaken to find a more corrosion resistant material to replace the existing 304L SS tubing. This paper presents the results from atmospheric exposure as well as electrochemical measurements on the corrosion resistance of AL-6XN (UNS N08367) and 254-SMO (UNS S32154). Type 304L SS (UNS S30403) was used as a control. Conditions at the Space Shuttle launch pad were simulated by using a hydrochloric acid (HC1) and alumina (Al203) slurry rinse for the atmospheric exposure and an electrolyte consisting of 3.55% sodium chloride (NaC1) with increased concentrations of hydrochloric acid (HC1) for the electrochemical measurements. The results from both types of measurements revealed the superior corrosion performance of the higher-alloyed materials. Unlike 304L SS, 254-SMO and AL-6XN exhibited a significantly improved resistance to corrosion as the concentration of hydrochloric acid in he 3.55% NaCl electrolyte solution was increased.

Calle, L. M.↗
NASA NTRS2004

Analysis of Regen Cooling in Rocket Combustors

The use of detailed CFD modeling for the description of cooling in rocket chambers is discussed. The overall analysis includes a complete three-dimensional analysis of the flow in the regenerative cooling passages, conjugate heat transfer in the combustor walls, and the effects of film cooling on the inside chamber. The results in the present paper omit the effects of film cooling and include only regen cooling and the companion conjugate heat transfer. The hot combustion gases are replaced by a constant temperature wall boundary condition. Load balancing for parallel cluster computations is ensured by using single-block unstructured grids for both fluids and solids, and by using a 'multiple physical zones' to account for differences in the number of equations. Validation of the method is achieved by comparing simple two-dimensional solutions with analytical results. Representative results for cooling passages are presents showing the effects of heat conduction in the copper walls with tube aspect ratios of 1.5:l.

Harper, Brent↗
NASA NTRS2002

Triggered Nucleation in Ni60Nb40 Using an Electrostatic Levitator

External triggering of nucleation in an undercooled liquid metal has been performed for the first time in an electrostatically levitated sample of undercooled eutectic Ni60Nb40. With the Electrostatic Levitator (ESL) facility at NASA/MSFC, NiNb alloys were externally nucleated at various undercooling increments. Observation of the resulting microstructure indicates that only one nucleation site is initiated with a trigger if the undercooling is sufficiently high. Well-defined transition zones exist in all the samples. An "anomalous" fine structured eutectic is initially grown from the nucleation point into the undercooled liquid followed by an unexpected variable width transition zone leading to a coarse structured region of dendrites. Our study tends to corroborate the findings of other studies on highly undercooled eutectics regarding a coupled growth zone within which the lamellar structure is formed and outside of which the anomalous is found.

Rathz, T.↗
NASA NTRS2000

Reduction of obesity, as induced by leptin, reverses endothelial dysfunction in obese (Lep(ob)) mice

Obesity is a major health care problem and is associated with significant cardiovascular morbidity. Leptin, a neuroendocrine hormone released by adipose tissue, is important in modulating obesity by signaling satiety and increasing metabolism. Moreover, leptin receptors are expressed on vascular endothelial cells (ECs) and mediate angiogenesis. We hypothesized that leptin may also play an important role in vasoregulation. We investigated vasoregulatory mechanisms in the leptin-deficient obese (ob/ob) mouse model and determined the influence of leptin replacement on endothelial-dependent vasorelaxant responses. The direct effect of leptin on EC nitric oxide (NO) production was also tested by using 4, 5-diaminofluorescein-2 diacetate staining and measurement of nitrate and nitrite concentrations. Vasoconstrictor responses to phenylephrine, norepinephrine, and U-46619 were markedly enhanced in aortic rings from ob/ob mice and were modulated by NO synthase inhibition. Vasorelaxant responses to ACh were markedly attenuated in mesenteric microvessels from ob/ob mice. Leptin replacement resulted in significant weight loss and reversal of the impaired endothelial-dependent vasorelaxant responses observed in ob/ob mice. Preincubation of ECs with leptin enhanced the release of NO production. Thus leptin-deficient ob/ob mice demonstrate marked abnormalities in vasoregulation, including impaired endothelial-dependent vasodilation, which is reversed by leptin replacement. These findings may be partially explained by the direct effect of leptin on endothelial NO production. These vascular abnormalities are similar to those observed in obese, diabetic, leptin-resistant humans. The ob/ob mouse may, therefore, be an excellent new model for the study of the cardiovascular effects of obesity.

NASA Program Biomedical Research and Countermeasur↗
NASA NTRS2000

High Undercooling of Ni59Nb41 Alloy in a Containerless Electrostatic Levitation Facility

Utilizing the containerless electrostatic levitation facility at NASA/MSFC, we were able to undercool the Ni-59Nb-41 (atomic) alloy by 210 K which was 160 deg. farther than the results of previous flight experiments. Undercoolings were clustered around 200 K during the repeated melting-freezing cycles on a single sample. Prior to this work, a metastable liquid separation had been presumed to limit the undercooling of this alloy. However, microstructural observations have revealed that undercooling was limited by crystal nucleation.

Robinson, M. B.↗
NASA NTRS2000

High Undercooling of Ni59Nb41 Alloy in a Containerless Electrostatic Levitation Facility

Utilizing the containerless electrostatic levitation facility at NASA/MSFC, we were able to undercool the Ni59Nb41 (atomic) alloy by 210 K which was 160 degrees farther than the results of previous flight experiments. Undercoolings were clustered around 200 K during the repeated melting-freezing cycles on a single sample. Prior to this work, a metastable liquid separation had been presumed to limit the undercooling of this alloy. However, microstructural observations have revealed that undercooling was limited by crystal nucleation.

Robinson, M. B.↗
NASA NTRS1999

Containerless, Low-Gravity Undercooling of Ti-Ce Alloys in the MSFC Drop Tube

Previous tests of the classical nucleation theory as applied to liquid-liquid gap miscibility systems found a discrepancy between experiment and theory in the ability to undercool one of the liquids before the L1-L2 separation occurs. To model the initial separation process in a two-phase liquid mixture, different theoretical approaches, such as free-energy gradient and density gradient theories, have been put forth. If there is a large enough interaction between the critical liquid and the crucible, both models predict a wetting temperature (T(sub w)) above which the minority liquid perfectly wets and layers the crucible interface, but only on one side of the immiscibility dome. Materials with compositions on the other side of the dome will have simple surface adsorption by the minority liquid before bulk separation occurs when the coexistence (i.e., binoidal) line in reached. If the interaction between the critical liquid and the crucible were to decrease, T(sub w) would increase, eventually approaching the critical consolute temperature (T(sub cc)). If this situation occurs, then there could be large regions of the miscibility gap where non-perfect wetting conditions prevail resulting in droplets of L1 liquid at the surface having a non-zero contact angle. The resulting bulk structure will then depend on what happens on the surface and the subsequent processing conditions. In the past several decades, many experiments in space have been performed on liquid metal binary immiscible systems for the purpose of determining the effects that different crucibles may have on the wetting and separation process of the liquids. Potard performed experiments that showed different crucible materials could cause the majority phase to preferentially wet the container and thus produce a dispersed microstructure of the minority phase. Several other studies have been performed on immiscibles in a semi-container environment using an emulsion technique. Only one previous study was performed using completely containerless processing of immiscible metals and the results of that investigation are similar to some of the emulsion studies. In all the studies, surface wetting was attributed as the cause for the similar microstructures or the asymmetry in the ability to undercool the liquid below the binoidal on one side of the immiscibility dome. By removing the container completely from the separation process, it was proposed that the loss of the crucible/liquid interaction would produce a large shift in T(sub w) and thus change the wetting characteristics at the surface. By investigating various compositions across the miscibility gap, a change in the type and amount of liquid wetting at the surface of a containerless droplet should change the surface nucleating behavior of the droplet - whether it be the liquid-liquid wetting or the liquid-to-solid transition. Undercooling of the liquid into the metastable region should produce significant differences in the separation process and the microstructure upon solidification. In this study, we attempt to measure these transitions by monitoring the temperature of the sample by optical pyrometry. Microstructural analysis will be made to correlate with the degree of undercooling and the separation mechanisms involved.

Robinson, M. B.↗
NASA NTRS1999

Direct Determination of the Metastable Liquid Miscibility Gap in Undercooled Cu-Co Alloys

Bulk Cu-Co alloys at compositions ranging from 10 to 80 wt pct Co were highly undercooled using a melt fluxing technique. The metastable liquid separation boundary has been directly determined from the measured temperature-time profiles. It was found that the critical point of the miscibility gap is slightly shifted towards the Co side and about 90 K below the liquidus. A droplet-shaped microstructure was observed for all solidified specimens (Cu- 10 to 80 wt pct Co), when the melts were undercooled into the metastable miscibility boundary.

Li, D.↗
NASA NTRS1998

Metastable Demixing of Supercooled Cu-Co and Cu-Fe Alloys in an Oxide Flux

A systematic study on the liquid separation in supercooled Cu-Co and Cu-Fe alloys was performed using a melt fluxing which permits high supercooling to be achieved. Moreover, this method renders it possible to directly measure binodal temperatures and establish metastable liquid miscibility gap (LMG). All phase-separated samples at compositions ranging from 10 to 80 wt pct Co or to 83 wt pct Fe were found to exhibit droplet-shaped morphologies, in spite of various droplet distributions. Uniformly dispersed microstructures were obtained as the minority component was less than 20 vol.%; while beyond this percentage, serious coarsening was brought about. Calculations of the miscibility gap in the Cu-Co system and Stokes movement velocity of Co and Fe droplets in Cu matrix were made to analyze the experimental results.

Li, D.↗