Engineering topics

Li, Jianlin

Publications and source records attributed to Li, Jianlin.

At least 19 records

DOE OSTI2024

Exploring the potential and impact of single-crystal active materials on dry-processed electrodes for high-performance lithium-ion batteries

Roll-to-roll powder-to-film dry processing (DP) and single-crystal (SC) active materials (AMs) with many advantages are two hot topics of lithium-ion batteries (LIBs). However, DP of SC AMs for LIBs is rarely reported. Consequently, the impact of SC AMs on dry-processed LIBs is not well understood. Herein, for the first time, via a set of experimental and theoretical studies of the conventional polycrystalline-AM- and SC-AM-based DPed electrodes (DPEs), this work not only reports a high-performance dry SC-AM cathode for LIB manufacturing, but also establishes some fundamental understanding of SC-based dry-processed electrodes, including their morphology, structure, mechanical strength, electronic conductivity and LIB electrochemical behavior. Further, the results suggest that DP of SC AMs is promising, which can dramatically improve the electrochemical kinetics at electrode level and particle level. Specifically, for the rate capability and long-term cyclability in full cells, SC DPEs exhibit a discharge specific capacity of 152.1 mAh g -1 at 1C and a capacity retention rate of 79.9 % at C/3 over 500 cycles, which are superior to those of PC DPEs (135.6 mAh g -1 and 68.3 %) at the same conditions and are further confirmed by the simulation data from the theoretical modelling study. Therefore, this comprehensive work marks a significant milestone for DP strategy and SC AMs, enlightening future research and development of LIB manufacturing.

25 ENERGY STORAGE↗

DOE OSTI2024

Comprehensive evaluation of commercially scalable atomic-layer-deposited alumina coating impact on full cell battery performance across varied test conditions

Atomic Layer Deposition (ALD) has emerged as a strategic enhancement method for lithium-ion battery (LIB) materials offering potential benefits and durability benefits for industrial battery production. However, the translation from laboratory achievements to commercial-scale applications has been limited. Here, this study aims to bridge this gap by comprehensively evaluating the effects of commercially scalable Al 2 O 3 ALD coatings using full pouch cell performance as a means to assess the ALD impact. We utilized large-scale slot-die coating techniques to ensure consistent electrode quality and tested four configurations of pouch cells to analyze the individual effects of ALD coating on anode and cathode electroactive materials. Our extensive testing matrix included long-term cycling, fast discharge, fast charge, leakage current, and high voltage tests. While at lower C-rates (<~1C), the influence of Al 2 O 3 coatings on cell performance is not significant. Fast charging conditions reveal that the anode ALD coating significantly enhances performance via a passivating effect, while on the cathode, it is detrimental, potentially due to increased resistance of the thin interfacial layer formed during the ALD processing. Leakage current and high-voltage tests show that the application of ALD coatings on either anode or cathode effectively minimizes side reactions at the electrode-electrolyte interface. Additionally, ALD coatings significantly mitigate concentrated and localized lithium plating on the anodes. These insights provide a valuable understanding of the potential of ALD technologies in LIB manufacturing to tailor cell performance, paving the way for safer, more efficient, and cost-effective battery solutions.

25 ENERGY STORAGE↗

DOE OSTI2024

In Situ Cyclized Polyacrylonitrile Coating: Key to Stabilizing Porous High-Entropy Oxide Anodes for High-Performance Lithium-Ion Batteries

High-entropy oxides (HEOs) composed of multiple metal elements have attracted great attention as anode materials for lithium-ion batteries (LIBs) due to the synergistic effects of various metal species. However, the practical applications of HEOs are still plagued by poor conductivity, unstable solid electrolyte interphase (SEI) and poor cycling stability. In this work, nanosized (FeCoNiCrMn) 3 O 4 HEO (NHEO) is prepared successfully by the NaCl-assisted mechanical ball-milling strategy. Novelly, polyacrylonitrile (PAN) is used as the binder and then in situ thermochemically cyclized to construct a cyclized PAN (cPAN) outer layer onto NHEO (NHEO-cPAN). The in situ formed cPAN coating not only improves the electrical conductivity, but also reinforces the structural and interfacial stability, and thereby, the resulted NHEO-cPAN electrode exhibits significantly enhanced rate and cyclic performance. Specifically, NHEO-PAN500 electrode delivers a high reversible capacity of 560 mAh g –1 at 5 A g –1 and a high-capacity retention of 83% over 800 cycles at 3 A g –1 . Furthermore, the structural evolution and electrochemical behavior of NHEO-PAN electrode during discharge/charge is systematically investigated by operando X-ray diffraction, in situ impedance spectroscopy and ex situ high-resolution transmission electron microscopy. Therefore, this work provides new insights into the engineering of electrode and interphase for high-performance HEO electrode materials, potentially enlightening the practical applications of HEO-based LIBs.

25 ENERGY STORAGE↗

DOE OSTI2024

Manufacturing Cathodes via Dry-Processing for Lithium-Ion Batteries

Conventional lithium-ion battery (LIB) electrodes are prepared through a wet slurry process with n-methyl pyrrolidone solvent, especially for cathodes. The wet slurry process encounters several disadvantages such as binder migration, electrode cracking in thick electrodes, energy intense heat-dry NMP solvent removal, and costly NMP recovery. The cost and energy consumption of coating and drying of electrode are about 11.5 % and > 46 % in LIB manufacturing, respectively. Thereby, it is essential to develop a facile roll-to-roll solvent-free LIB electrode processing for reducing the cost and energy consumption. Recently, the Maxwell-type dry processing (DP) shines new lights on LIB manufacturing, which mainly bases on dry mixing (DM) of electrode component powder followed by calendering into electrode films and laminating onto current collectors, realizing the rapid manufacturing of LIB electrodes in a powder-to-film manner for industries. This report shares some recent progress on the DP from our group. We aim to further advance the manufacturing science of DP by correlating the processing conditions with electrode properties and performance. Particularly, we investigate the effect of DM, and compression on the polytetrafluoroethylene (PTFE) binder fiberization, porosity, mechanical properties, electrical conductivity and electrochemical behaviors of electrodes. The DM study suggests that PTFE fiberization heavily relies on the degree of DM. Insufficient DM results in poor PTFE fiberization while outrageous DM damages the formed PTFE fibers. Both negatively affect the mechanical behaviors of the electrodes and their rate capability. However, moderate DM is highly beneficial. In addition, our study of the porosity impact reveals that LiNi0.8Mn0.1Co0.1O2 (NMC) secondary particles can be broken into primary particles due to compression, especially at low porosity. Those fractured NMC secondary particles exhibit lower modulus. We propose that a moderate porosity of around 32% favors the electronic conductivity, charge transfer impedance and rate capability. The study of the cathodic electrolyte interphase layer of PTFE-based DPed electrode confirms that side reactions of PTFE binder due to the formation of LiF in LiClO4-based electrolyte.

Tao, Runming↗

DOE OSTI2024

Relithiation process for direct regeneration of cathode materials from spent lithium-ion batteries

A method for the regeneration of cathode material from spent lithium-ion batteries is provided. The method includes dissolving a lithium precursor in a polyhydric alcohol to form a solution. Degraded cathode material containing lithium metal oxides are dispersed into the solution under mechanical stirring, forming a mixture. The mixture is heat treated within a reactor vessel or microwave oven. During this heat treatment, lithium is intercalated into the degraded cathode material. The relithiated electrode material is collected by filtration, washing with solvents, and drying. The relithiated electrode material is then ground with a lithium precursor and thermally treated at a relatively low temperature for a predetermined time period to obtain regenerated cathode material.

Belharouak, Ilias↗

DOE OSTI2024

In-situ ionothermal synthesis of nanoporous carbon/oxide composites: A new key to functional separators for stable lithium-sulfur batteries

Lithium-sulfur batteries (LSBs) with high energy density are promising for energy storage. However, conventional polypropylene-based separator cannot avoid polysulfides shuttling which impedes the practical application of LSBs. Herein, an in-situ ionothermal synthesis strategy that concurrently applies ionic liquid as the solvent, template and high-yield carbon source is proposed for the facile preparation of nanoporous carbon/oxide composite separator modifiers. The composites exhibit features of high polarity, self doping, oxygen vacancy, heteroatom doping, abundant defects and high electronic conductivity. Theoretical and experimental studies suggest that the composites can efficiently trap and convert polysulfides for high-performance LSBs. Indeed, in the composite-modified LSBs with next-generation roll-to-roll dry-processed high-loading sulfur cathodes, enhanced performance is achieved, revealing the effectiveness of the composites as functional materials towards separator modification. Therefore, the proposed strategy and its delivered nanoporous composites exhibit excellent versatility and practicality for high-performance LSBs.

25 ENERGY STORAGE↗

DOE OSTI2024

Multifunctional nitrile additives for inducing pseudo-concentration gel-polymer electrolyte: Enabling stable high-voltage lithium metal batteries

High-voltage lithium metal batteries (LMBs) are promising for next-generation high-energy storage systems. Unfortunately, their implementation has been severely plagued by the interfacial instability between the high-voltage cathodes/lithium metal (LM) anodes and electrolytes. To tackle these challenges, a novel nitrile additive, 1,4-dicyanobenzene (DCB) (Synonyms: terephthalonitrile), is added to the in situ polymerized pentaerythritol tetraacrylate-based gel polymer electrolyte (GPE). The DCB additive, as demonstrated both theoretically and experimentally, plays a crucial role in altering the Li+ coordinated solvation structure within the GPE. This alteration leads to the formation of a pseudo-concentrated electrolyte with a tightly packed Li+ cluster, expanding the electrochemical stability window of the electrolyte. Moreover, the DCB-included GPE significantly improves its compatibility with both LM anode and high-voltage cathode, attributed to the modified solvation structure and the generated LiF-rich electrolyte/electrode interphases. Accordingly, the GPE enables stable cyclic performance of LMBs based on a 4.9 V LiNi 0.5 Mn 1.5 O 4 cathode at a low relative negative/positive ratio of 4, achieving a high reversible capacity of 123.8 mAh g -1 with a capacity retention of 87.7% over 500 cycles at 0.5 C. This work provides new insights into enhancing the cyclability of high-voltage LMBs via the synergistic effect of additives and GPE.

25 ENERGY STORAGE↗

DOE OSTI2024

Mechanical and Electrochemical Implications of Drying Temperature on Lithium‐Ion Battery Electrodes

Abstract Lithium‐ion battery (LIB) electrodes are typically produced with n‐methyl‐2‐pyrrolidone, a toxic solvent that is a known carcinogen and reproductive hazard. Accordingly, aqueous processing has been an expanding area of research interest in the field of LIB manufacturing. Although aqueous processing has been widely successful in anode processing, serious challenges remain in processing the cathode. In this work, the drying mechanics of cathode processed with both solvents is investigated though implementation of a chemical‐engineering‐based model to better understand the utilization of heat provided by experimentally determining the heat and mass transfer coefficients. Electrochemical performance is also evaluated to determine the impact of drying temperature on cycling performance. Binder distribution is determined via various methods to confirm differences in binder homogeneity as a function of both solvent and drying temperature. Identified is the large difference in the efficiency in which the heat is used as well as an ideal drying temperature for both aqueous and non‐aqueous processed cathodes. Also identified is the increased sensitivity to processing temperature for aqueous processed electrodes compared to non‐aqueous processed counterparts, pointing to the possibility of tuned drying regimes which would capitalize on the potential cost savings of aqueous processing for cathodes.

25 ENERGY STORAGE↗

DOE OSTI2024

Dataset of mechanically induced thermal runaway measurement and severity level on Li-ion batteries

The deployment of Li-ion batteries covers a wide range of energy storage applications, from mobile phones, e-bikes, electric vehicles (EV) and stationary energy storage systems. However, safety issue such as thermal runaway is always one of the most important concerns to prevent Li-ion batteries from further market penetration. A standardized single-side indentation test protocol was developed to mechanically induce an internal short-circuit. The cell voltage, compressive load, indenter stroke, and temperature at the indentation point are measured in time series. The test data of each cell, along with cell parameters such as dimensions, mass, chemistry, state of charge (SOC), capacity, are integrated together to calculate a thermal runaway severity score from 0 to100. Complete data collection process including the original measured record, test method, severity score calculation scheme is presented in this article. The thermal runaway severity analysis and the more than 100 tested Li-ion battery records provide a good data source for further comparison and ranking of thermal runaway risks.

25 ENERGY STORAGE↗

DOE OSTI2024

Lithiophilic CoF 2 @C hollow spheres towards spatial lithium deposition for stable lithium metal batteries

Lithium metal (LM) is a promising anode for next-generation batteries due to its high theoretical capacity and low electrode potential. Nonetheless, side reactions, volume change, and unwanted lithium dendrite growth seriously limit the practical application of LM. Herein, with the aid of a hard template approach, a novel lithiophilic CoF 2 -carbon hollow sphere (CoF 2 @C-HS) composite material is successfully prepared via a facile in-situ fluorination and etching strategy. The lithiophilic CoF 2 acts as nucleation sites to reduce nucleation overpotential as well as induces the spatial Li deposition and the formation of LiF-rich solid electrolyte interphase (SEI), and the hollow carbon matrix can enhance the electrical conductivity and offer free space for LM deposition. Theoretical simulations reveal that the synergistic effect of lithiophilic CoF 2 and hollow carbon matrix homogenizes the electric field distribution and Li + flux. Benefiting from these advantages, the CoF 2 @C-HS-modified copper substrate electrode delivers an enhanced Coulombic efficiency (CE) of 93.7% for 280 cycles at 1 mA cm –2 and 1 mA h cm –2 . The symmetrical cell using CoF 2 @C-HS can stably cycle more than 1800 h with a low voltage hysteresis of 11 mV at a current density of 0.5 mA cm –2 and an areal capacity of 0.5 mA h cm –2 . Moreover, the Li@CoF 2 @C-HS composite anode enables more than 300 stable cycles at 1 C with a capacity retention of 95% in LiFePO 4 -based full cell and 110 stable cycles at 1 C in LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811)-based high-voltage full cell. Finally, this work might shed a new light on designing lithiophilic hosts to spatially confine LM deposition, realizing dendrite-free LM anodes and the practical applications of LM batteries.

25 ENERGY STORAGE↗

DOE OSTI2024

Direct regeneration of lithium ion cathodes by ionothermal relithiation

A method for relithiating cathode material from spent lithium-based batteries, the method comprising: (i) mixing delithiated cathode material and a lithium salt with an ionic liquid in which the lithium salt is at least partially soluble to form an initial mixture; (ii) heating the initial mixture to a temperature of 100° C. to 300° C. to result in relithiation of the delithiated cathode material; and (iii) separating the ionic liquid from the relithiated cathode material; wherein, in embodiments, the cathode material is a lithium metal oxide, wherein the metal is selected from the group consisting of Ni, Co, Fe, Mn, Al, Zr, Ti, Nb, and combinations thereof, or wherein the cathode material has the formula LiNi x Mn y Co z O 2 , wherein x>0, y>0, z>0, and x+y+z=1; wherein, in some embodiments, the ionic liquid has a nitrogen-containing cationic portion, such as an imidazolium ionic liquid.

Luo, Huimin↗

DOE OSTI2024

Method of solvent-free manufacturing of composite electrodes incorporating radiation curable binders

A method of making an electrode includes the step of mixing active material particles, radiation curable resin precursors, and electrically conductive particles to create an electrode precursor mixture. The electrode precursor mixture is electrostatically sprayed onto a current collector to provide an electrode preform. The electrode preform is heated and calendered to melt the resin precursor such that the resin precursor surrounds the active particles and electrically conductive particles. Radiation is applied to the electrode preform sufficient to cure the radiation curable resin precursors into resin.

Du, Zhijia↗

DOE OSTI2024

Interface Modifications of Lithium Metal Anode for Lithium Metal Batteries

Lithium metal batteries (LMBs) enable much higher energy density than lithium–ion batteries (LIBs) and thus hold great promise for future transportation electrification. However, the adoption of lithium metal (Li) as an anode poses serious concerns about cell safety and performance, which has been hindering LMBs from commercialization. To this end, extensive effort has been invested in understanding the underlying mechanisms theoretically and experimentally and developing technical solutions. In this review, we devote to providing a comprehensive review of the challenges, characterizations, and interfacial engineering of Li anodes in both liquid and solid LMBs. Finally, we expect that this work will stimulate new efforts and help peer researchers find new solutions for the commercialization of LMBs.

25 ENERGY STORAGE↗

DOE OSTI2024

Efficient recovery processes for the black mass from spent lithium-ion batteries

A method of recycling lithium-ion batteries is disclosed. The method includes isolating a composite electrode that comprises an electrode material adhered to a current collector with a polyvinylidene difluoride (PVDF) binder from a spent lithium-ion battery. The method also includes contacting the composite electrode in a polyol fluid capable of releasing the PVDF binder from the current collector without substantially altering either component. The composite electrode may be a cathode or an anode. The method also includes rapidly delaminating the electrode material from the current collector to give a free electrode material and a free current collector, and recovering each of the free electrode material and the free current collector from the mixture. The free electrode material may be reused to prepare another composite electrode, as well as a lithium-ion battery comprising the same, which are also disclosed.

Belharouak, Ilias↗

DOE OSTI2024

Microwave-Absorbing Foams with Adjustable Absorption Frequency and Structural Coloration

Microwave-absorbing materials with regulatable absorption frequency and optical camouflage hold great significance in intelligent electronic devices and advanced stealth technology. Herein, we present an innovative microwave-absorbing foam that can dynamically tune microwave absorption frequencies via a simple mechanical compression while in parallel enabling optical camouflage over broad spectral ranges by adjusting the structural colors. In this study, the vivid colors spanning different color categories generated from thin-film interference can be precisely regulated by adjusting the thickness of the conformal TiO 2 coatings on Ni/melamine foam. Enhanced interfacial and defect-induced polarizations resulting from the introduction of TiO 2 coating synergistically contribute to the dielectric attenuation performance. Consequently, such a foam exhibits exceptional microwave absorption capabilities, and the absorption frequency can be dynamically tuned from the S band to the Ku band by manipulating its compression ratio. Additionally, simulation calculations validate the adjustable electromagnetic wave loss behavior, offering valuable insights for the development of next-generation intelligent electromagnetic devices across diverse fields.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Directing CO 2 electroreduction pathways for selective C 2 product formation using single-site doped copper catalysts

Manipulating the selectivity-determining step in post-C–C coupling is crucial for enhancing C 2 product specificity during electrocatalytic CO 2 reduction, complementing efforts to boost rate-determining step kinetics. Here we highlight the role of single-site noble metal dopants on Cu surfaces in influencing C–O bond dissociation in an oxygen-bound selectivity-determining intermediate, steering post-C–C coupling toward ethylene versus ethanol. Integrating theoretical and experimental analyses, we demonstrate that the oxygen binding strength of the Cu surface controls the favorability of C–O bond scission, thus tuning the selectivity ratio of ethylene-to-ethanol. The Rh-doped Cu catalyst with optimal oxygen binding energy achieves a Faradaic efficiency toward ethylene of 61.2% and an ethylene-to-ethanol Faradaic efficiency ratio of 4.51 at –0.66 V versus RHE (reversible hydrogen electrode). Integrating control of both rate-determining and selectivity-determining steps further raises ethylene Faradaic efficiency to 68.8% at 1.47 A cm -2 in a tandem electrode. Our insights guide the rational design of Cu-based catalysts for selective CO 2 electroreduction to a single C 2 product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Nanoscale Ion Transport Enhances Conductivity in Solid Polymer-Ceramic Lithium Electrolytes

The predictive design of flexible and solvent-free polymer electrolytes for solid-state batteries requires an understanding of the fundamental principles governing the ion transport. In this work, we establish a correlation among the composite structures, polymer segmental dynamics, and lithium ion (Li + ) transport in a ceramic-polymer composite. Elucidating this structure–property relationship will allow tailoring of the Li + conductivity by optimizing the macroscopic electrochemical stability of the electrolyte. The ion dissociation from the slow polymer segmental dynamics was found to be enhanced by controlling the morphology and functionality of the polymer/ceramic interface. The chemical structure of the Li + salt in the composite electrolyte was correlated with the size of the ionic cluster domains, the conductivity mechanism, and the electrochemical stability of the electrolyte. Polyethylene oxide (PEO) filled with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) or lithium bis(fluorosulfonyl) imide (LiFSI) salts was used as a matrix. A garnet electrolyte, aluminum substituted lithium lanthanum zirconium oxide (Al-LLZO) with a planar geometry, was used for the ceramic nanoparticle moieties. Further, the dynamics of the strongly bound and highly mobile Li + were investigated using dielectric relaxation spectroscopy. The incorporation of the Al-LLZO platelets increased the number density of more mobile Li + . The structure of the nanoscale ion-agglomeration was investigated by small-angle X-ray scattering, while molecular dynamics (MD) simulation studies were conducted to obtain the fundamental mechanism of the decorrelation of the Li + in the LiTFSI and LiFSI salts from the long PEO chain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Freeze Tape Casting Electrode with Bilayered Architecture for High-Performance Lithium-Ion Batteries

A facile freeze tape casting (FTC) strategy is utilized to prepare bilayered 4 mAh cm –2 high-loading LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathodes. The bottom layer is a conventional nonaqueous electrode, which has a dense structure for high-energy purposes. Further, the top layer is prepared by the proposed FTC, exhibiting a porous feature for high-power requirement. With the assistance of FTC, the bilayered electrodes successfully deliver enhanced rate and cyclic performance due to the improved lithium-ion diffusion kinetics and pathways. Therefore, the proposed FTC strategy and its delivered electrodes are promising for energy- and power-density lithium-ion batteries, potentially enlightening the research and development of lithium-ion battery manufacturing.

25 ENERGY STORAGE↗