Engineering topics

Li, Jianlin

Publications and source records attributed to Li, Jianlin.

At least 55 records · Page 3

DOE OSTI2022

In-situ synthesis of porous metal fluoride@carbon composite via simultaneous etching/fluorination enabled superior Li storage performance

Transition metal fluorides as Li-free conversion-type cathode materials have high theoretical specific capacities, however, their preparation strategy, sluggish electrochemical kinetic and poor cyclability have impeded their wide adoption in lithium-ion batteries. Herein, a facile in-situ synthesis of porous metal-fluoride-carbon composites is accomplished via simultaneous polytetrafluorethylene-based hard template etching and metal fluorination. This not only facilitates fast electron transfer and lithium-ion diffusion kinetics, but also buffers severe volume fluctuation during lithiation/delithation and enables the formation of a uniform and thin Li 2 CO 3 /LiF-rich cathode-electrolyte interphase. Here, as a proof of concept, the as-prepared porous FeF 3 @C (p-FeF 3 @C) indeed exhibits a high specific capacity of 230 mAh g -1 at 0.1 C together with an excellent capacity retention of 92.5% at 1 C for 200-cycles. Moreover, the practicality of the strategy is demonstrated by the superb electrochemical performance of the full-cells coupled with pre-lithiated graphite anodes. Therefore, the proposed novel synthetic strategy will enlighten the future design of high-performance metal-fluoride-carbon composites with porous structure for energy storage applications.

25 ENERGY STORAGE↗

DOE OSTI2022

Catalyst layer formulations for slot-die coating of PEM fuel cell electrodes

The series of electrodes were fabricated by the scalable and manufacturable slot-die coating method for proton exchange membrane fuel cell (PEMFC) application. The inks with different amounts of solids were studied by rheological methods in order to establish a coating window with minimum manufacturing defects. The obtained electrodes were characterized by SEM, AFM, and optical microscopy, which showed that they were uniform and homogeneous with minimum defects. The electrochemical evaluation of the manufactured gas diffusion electrodes (GDE) showed that the main characteristics of the electrodes, like electrochemical surface area, proton resistivity, and double layer capacitance, were found to be close for all samples confirming the reproducibility of the slot-die process. Additionally, we studied the effects of membrane thickness on the performance of the GDE membrane electrode assemblies and determined that a decrease in membrane thickness favored the performance. Furthermore, the obtained results clearly demonstrated the applicability and feasibility of the approach for the Manufacturing of catalyst layers for the fuel cell application with potential for future mass production.

08 HYDROGEN↗

DOE OSTI2022

Investigation of oxygen evolution reaction with Ni foam and stainless-steel mesh electrodes in alkaline seawater electrolysis

We report alkaline seawater electrolysis is a promising method for hydrogen production; however, little progress has been made in investigating the substrates for oxygen evolution reaction (OER) electrocatalysts. Ni foam and stainless-steel mesh (SS mesh) were investigated systematically for OER in alkaline seawater electrolysis in this work. The overpotentials and Tafel slopes with SS meshes are smaller than Ni foams, and it also exhibits excellent stability. Interestingly, the performance of the SS mesh even outperforms various non-noble metal electrocatalysts and is comparable to commercial RuO2 and IrO2. The corrosion conditions of Ni foam and SS mesh electrodes were studied and revealed. Furthermore, the electrochemically active surface area (ECSA) of Ni foam is 12 times higher than SS mesh in the same geometric area, indicating the electrochemical activity of SS mesh is much superior to Ni foam. This work expands on promising substrates for alkaline seawater electrolysis, with cost and performance advantages.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Understanding slurry formulations to guide solution-processing of solid electrolytes

Scalable processing of thin solid electrolytes is crucial for engineering solid-state batteries with practical energy densities. To leverage existing battery production infrastructure, pathways for solution processing of solid electrolyte films must be investigated. Here, roll-to-roll compatible film preparation of aluminum-doped lithium lanthanum zirconate oxide was studied. Four slurry configurations accounting for different solvent properties and solid loadings were evaluated to investigate the ternary interactions within the dispersions. Rheological and coating stability analyses were carried out on the processed slurries. The analysis and characterization indicated that improved component interactions within the ethanol/toluene system result in homogenized distribution of the particles, binder, and plasticizer, and enable the extraction of free-standing thin films with thicknesses of 20 μm and large area (>15 in. 2 ). The drawbacks and opportunities of several protocols for high temperature sintering of the dried green films were investigated. This study highlights the importance of engineering dispersions during the development of processing protocols for solid electrolytes and provides guidelines for the best practices that can be leveraged for solution processing–based fabrications for a wide range of solid electrolyte materials.

25 ENERGY STORAGE↗

DOE OSTI2022

Editorial for focus on nanophase materials for next-generation lithium-ion batteries and beyond

Lithium-ion batteries (LIBs) have revolutionized our society in many respects, and we are expecting even more favorable changes in our lifestyles with newer battery technologies. In pursuing such eligible batteries, nanophase materials play some important roles in LIBs and beyond technologies. Here, stimulated by their beneficial effects of nanophase materials, we initiated this Focus. Excitingly, this Focus collects 13 excellent original research and review articles related to the applications of nanophase materials in various rechargeable batteries, ranging from nanostructured electrode materials, nanoscale interface tailoring, novel separators, computational calculations, and advanced characterizations.

25 ENERGY STORAGE↗

DOE OSTI2022

Stress evolution and thickness change of a lithium-ion pouch cell under various cycling conditions

We report to design large-sized lithium-ion battery modules for the application of electric vehicles and grid-level energy storage, it is of important significance to understand how stress and dimension of a single pouch cell fluctuate during charge/discharge cycles. In this study, stress evolution under the constant-thickness condition and thickness change under the constant-stress condition are measured for in-house fabricated pouch cells, respectively. The results of stress measurements show that the stress increase percentage generally decreases when the charge/discharge current increases, regardless of the value of the initial compressive stress. With the same current density, the stress increase percentage generally increases when the upper cutoff voltage increases. With the same current density and upper cutoff voltage, the stress increase percentage decreases when the initial compressive stress increases. The results of thickness measurements show that the volume expansion percentage generally increases when the current density increases, regardless of the value of the constant compressive stress. With the same current density, the volume expansion percentage generally increases when the upper cutoff voltage increases. With the same current density and upper cutoff voltage, the volume expansion decreases when the constant compressive stress increases. The results provide important insights into the design principles of battery packs.

25 ENERGY STORAGE↗

DOE OSTI2022

Cobalt-free layered oxide cathodes

A cathode and a battery providing the cathode is provided. The cathode comprises a lithium metal oxide. The lithium metal oxide comprises nickel, aluminum, and iron. The lithium metal oxide is substantially free of cobalt. The battery comprises an anode, the cathode, a separator, and an electrolyte.

Belharouak, Ilias↗

DOE OSTI2022

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration - Early Stage R&D: Phase 2 and FY21 (Final Report)

R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto substrates or membranes that are on moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final product. Established methods that typify R2R processing include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating, and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes and electrolytes for energy storage, and barrier and membrane materials for decarbonization and air and water filtration. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, the means must be available to enable manufacture of these products in a cost-competitive manner. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations and the coating and heated drying processes to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Review—Electrospun Inorganic Solid-State Electrolyte Fibers for Battery Applications

Inorganic solid-state electrolytes (SSEs), especially Li 7 La 3 Zr 2 O 12 (LLZO), are promising candidates for all solid-state batteries. Generally, SSEs are synthesized by solid-state reactions at high temperatures. The high temperature required to synthesize useful polymorphs (e.g., cubic phase, in the case of LLZO) increases their production cost. To lower the synthesis temperature, several approaches, including doping and crystallite size control via sol-gel processes, have been explored. Recently, electrospinning was used to synthesize the inorganic SSE fibers to control the crystallite size and lower the calcination temperature. Several publications followed that investigated the properties of fibers and demonstrated the use of these fibers in inorganic-polymer composite SSEs. This paper presents a concise discussion of electrospinning, the parameters that control fiber morphology, the synthesis of inorganic SSE fibers, the effect of sintering conditions on the fiber morphology and composition, and the recent use of these fibers in making composite SSEs and other battery applications. Additionally, most of the discussion focuses on LLZO, but this paper also discusses applications of other types of electrospun inorganic electrolyte fibers, the challenges of using these fibers, and possible future directions in this research field.

25 ENERGY STORAGE↗

DOE OSTI2022

Bilayer hybrid graphite anodes via freeze tape casting for extreme fast charging applications

Extreme fast charging (XFC) of lithium-ion batteries is critical for continuous market adoption of electric vehicles. However, mass transport limitations and sluggish kinetics lead to lithium plating in graphite anodes under fast charging conditions. One approach to address the mass transport limitation in graphite is to design low-tortuosity electrodes to enhance ionic transport. In this study, a bilayer hybrid structured electrode with directionally aligned channels was developed via freeze tape casting, which enables faster lithium ion diffusion through the graphite electrode. A scalable roll-to-roll process was designed in which slurry can be cast on any substrates for simple processing. Additionally, electrochemical impedance spectroscopy measurements indicated that the bilayer hybrid coating had both low tortuosity and short diffusion pathways, enabling XFC charging. Rate testing for the bilayer hybrid electrode indicated superior performance over the other coatings, exhibiting a ~20% improvement in the charge capacity compared with the conventional coating at 5C and 10 min total charging time. The bilayer hybrid electrode also demonstrated a 10% improvement in capacity retention compared with the conventional electrode after 1000 cycles at XFC conditions. This study demonstrates freeze tape casting as a scalable way to fabricate low-tortuosity electrodes for XFC applications.

25 ENERGY STORAGE↗

DOE OSTI2022

Correlation of Oxygen Anion Redox Activity to In‐Plane Honeycomb Cation Ordering in Na x Ni y Mn 1− y O 2 Cathodes

Sodium‐ion batteries (SIBs) are one of the most promising next‐generation energy storage systems because of their abundant and low‐cost component materials. However, the lower energy density of SIBs compared with lithium‐ion batteries diminishes their practical value proposition. Among the many sodium‐based cathodes, layered transition metal oxides with high sodium content have energy densities comparable with the lithium‐ion battery technology. When charged above 4.1 V, the sodium‐based cathodes often undergo transformations because the activation of oxygen anion redox causes irreversible oxygen release, transition metal ion migration, lattice distortion, and rapid capacity decay. Here, in situ gas analysis is performed to evaluate the lattice oxygen anion redox activity in Na x Ni y Mn 1− y O 2 cathodes with P2 and O3 structural orderings. Operando X‐ray diffraction and neutron diffraction are performed to assess the structural changes related to lattice oxygen redox and transition metal ion migration in Na x Ni y Mn 1− y O 2 cathodes. The results unveil that in‐plane honeycomb cationic ordering can help suppress oxygen anion redox activity, which is critical for the future design of layered transition metal oxide cathodes that are prone to achieve high‐energy for durable SIBs.

25 ENERGY STORAGE↗

DOE OSTI2022

Performance of Different Water-Based Binder Formulations for Ni-Rich Cathodes Evaluated in LiNi 0.8 Mn 0.1 Co 0.1 O 2 //Graphite Pouch Cells

Water-based processing for lithium-ion battery electrodes is attractive due to its lower manufacturing cost and smaller environmental impact. However, multiple challenges associated with aqueous cathode processing have hindered commercial adoption. Polymer binders are an important component of the electrode, and thus the choice of binders can alter electrode cycling performance significantly. In this work, four different water-based binder combinations are investigated for Ni-rich LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811)-based cathodes, with a focus on the long-term electrochemical performance in practical-format full pouch cells. No additional pH-modulating additives were added to the aqueous cathode slurries, and no protective coatings were present on the cathode or aluminum current collector. Results are compared with the standard PVDF/NMP-based binder/solvent combination, used as a baseline. The influence of water-based binder type on slurry rheology and electrode microstructure are also discussed. All cells made by water-processing had worse rate performance compared to the baseline. However, the cell discharge capacity after 1000 U.S. Advanced Battery Consortium (USABC) cycles at C/3 charge/discharge rate was comparable to the baseline for two of the water-based cathode formulations (CMC & JSR, and LiPAA), demonstrating the potential viability of aqueous-processed Ni-rich cathodes at a commercial scale.

25 ENERGY STORAGE↗

DOE OSTI2022

Method of solvent-free manufacturing of composite electrodes incorporating radiation curable binders

A method of making an electrode includes the step of mixing active material particles, radiation curable resin precursors, and electrically conductive particles to create an electrode precursor mixture. The electrode precursor mixture is electrostatically sprayed onto a current collector to provide an electrode preform. The electrode preform is heated and calendered to melt the resin precursor such that the resin precursor surrounds the active particles and electrically conductive particles. Radiation is applied to the electrode preform sufficient to cure the radiation curable resin precursors into resin.

25 ENERGY STORAGE↗

DOE OSTI2022

A Bilayer Electrolyte Design to Enable High-Areal-Capacity Composite Cathodes in Polymer Electrolytes Based Solid-State Lithium Metal Batteries

High-areal-capacity cathodes are needed for energy-dense solid-state batteries. Here, we demonstrate a bilayer polymer electrolyte design for cycling 3–6 mAh/cm 2 NMC811 composite cathodes. In this work, the bilayer electrolyte comprises a cross-linked poly(ethylene oxide) (PEO)-based electrolyte layer and a linear-PEO-based electrolyte layer. The former provides dendritic resistance, and the latter provides a seamless interface with the cathode during cycling. Using a single layer of either membrane led to severe shorting or extremely low Coulombic efficiency (CE) in the first cycle. The general concept of a rigid dendrites-inhibiting electrolyte facing Li anode and a softer, cathode-integrated electrolyte that ensures contact with the cathodes during cycling may present a pattern for enabling high-energy-density cathodes.

25 ENERGY STORAGE↗

DOE OSTI2022

Deconvoluting sources of failure in lithium metal batteries containing NMC and PEO-based electrolytes

Solid-state lithium metal batteries (SSLMBs) containing polyethylene oxide (PEO)-derived polymer electrolytes and high-voltage (> 4 V vs. Li/Li + ) cathode materials suffer from three sources of failure: (1) instability between the polymer electrolyte and cathode at high voltage, (2) instability of the polymer electrolyte with Li metal, and (3) poorly-designed cathodes. In this study, these three sources of failure are deconvoluted by studying Ni-rich LiNi x Mn y Co 1-x-y O 2 (NMC, x ≥ 0.6) cathodes and a gel polymer electrolyte (GPE) derived from PEO. Initial cycling data reveals that rapid capacity fade occurs regardless of whether soft short circuits form due to Li dendrites. Cyclic voltammetry scans on cells featuring a Li metal electrode, GPE, and a NMC811 electrode free of additives suggest that there are no runaway reactions between the GPE and NMC811 up to 4.5 V vs. Li/Li + . Cathode/cathode symmetric cell cycling demonstrates that Li metal reactivity is a prime source of failure, though a poorly-designed cathode leads to subpar performance. A cathode with single-crystal NMC particles was demonstrated to achieve better initial capacity and longer cycle life, indicating room for improvement in SSLMB cathode design. Therefore, the sources of failure as enumerated may be ranked as follows from most to least concerning: 2 > 3 > 1.

25 ENERGY STORAGE↗

DOE OSTI2022

Deconvoluting the benefits of porosity distribution in layered electrodes on the electrochemical performance of Li-ion batteries

Thick Lithium Ion Battery (LIB) electrodes suffer from poor rate capability and high ionic impedance due to their thickness and mesostructure. Therefore, optimizing thick electrode architectures becomes crucial. In this work, we report a systematic assessment of the ionic resistance in heterogeneous porous electrodes through the combination of computational simulations using a 4D-resolved model and experimental measurements. The first part of the study is devoted to a general assessment of Electrochemical Impedance Spectroscopy (EIS) spectra, mapping the impact of ionic and electronic resistances on the overall impedances of uncalendered and calendered LiNi 1/3 Mn 1/3 Co 1/3 O 2 , LiFePO 4 and graphite electrodes. In the second part, in silico-generated electrodes with different porosities are used in computational EIS simulations to analyze the impact of the electrode porosity on the ionic impedance. As expected, the results show that a lower porosity leads to a higher ionic impedance because of a higher electrode tortuosity factor. Furthermore, in silico-generated electrodes with different porosities were stacked and assembled to create heterogeneities of porosity along the thickness, and used in computational EIS and galvanostatic discharge simulations. The computational results show that the porosity heterogeneity along the electrode thickness has a significant effect on the ionic impedance and capacity of the electrode. The electrode architecture with progressively decreasing porosity from separator to current collector shows the highest performance, a trend validated by our in house experimental EIS and galvanostatic discharge also reported in this manuscript. Overall, we conclude that the ionic resistance in a thick electrode can be effectively reduced through proper tuning of the porosity heterogeneity. The proposed heterogeneous electrode architectures presented here could enormously help building efficient thick electrodes for LIBs.

25 ENERGY STORAGE↗

DOE OSTI2022

Reduced Graphene Oxide Aerogels with Functionalization-Mediated Disordered Stacking for Sodium-Ion Batteries

Surface modified reduced graphene oxide (rGO) aerogels were synthesized using the hydrothermal method. Ethylene diamine (EDA) and α-cyclodextrin (CD) were used to functionalize the surface of the graphene oxide layers. The oxygen reduction and surface modification occurred in-situ during the hydrothermal self-assembly process. The chemical functionality and structure of the resulting ethylene diamine modified (rGO-EDA) and cyclodextrin modified (rGO-CD) aerogels as well as of the pristine unmodified rGO aerogel were studied using XPS, SEM, XRD, and SANS techniques. The overall surface composition showed a significant decrease in the oxygen content for all synthesized aerogels. The surface modified aerogels were characterized by a disordered stacking of the assembled rGO layers. The surface functionalities resulted in a broad distribution of the interlayer spacing and introduced structural heterogeneities. Such disordered structures can enable a better adsorption mechanism of the sodium ions. Coin cells based on the synthesized aerogels and sodium metal were assembled and tested at several charge and discharge rates. The correlation between the surface functionality of the rGO, the induced structural heterogeneities due to the disordered stacking, and the electrochemical performance of sodium-ion batteries were investigated. Operando XRD measurements were carried out during the battery cycling to investigate the adsorption or intercalation nature of the sodiation mechanism.

25 ENERGY STORAGE↗

DOE OSTI2021

Design and processing for high performance Li ion battery electrodes with double-layer structure

A two-layer LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathode has been designed and fabricated containing a “power layer” and “energy layer”, with corresponding porosity and particle size prescribed to each layer to achieve best utilization of electrode material (maximum integrated depth of discharge across the electrode thickness) at high applied current. The cathode showed a 17% improvement in capacity when tested in symmetric cells. When applying the design to a full cell, where both positive and negative electrodes contain power and energy layers, a 74% increase in discharge capacity at 2C was achieved compared to the cell with conventional electrodes. Furthermore, this demonstrates an avenue to increase energy and power density of lithium–ion batteries and enable fast charging capability.

25 ENERGY STORAGE↗