Engineering topics

Li, Jianlin

Publications and source records attributed to Li, Jianlin.

At least 91 records · Page 5

DOE OSTI2020

Roll-To-Roll Atomic Layer Deposition of Titania Nanocoating on Thermally Stabilizing Lithium Nickel Cobalt Manganese Oxide Cathodes for Lithium Ion Batteries

Conformal coating of ceramic layers (nm-thick) on Ni-rich layered cathode materials is an effective strategy for improving high-temperature longevity of Li-ion batteries (LIBs). In this work, we develop a roll-to-roll atomic layer deposition (R2R ALD) apparatus for growing uniform nanolayers of TiO 2 . We explore the effect of ALD parameters (temperature: 120–180 °C and line speed: 2–40 mm s –1 ) on the TiO 2 surface coating and subsequently investigate the electrochemical performance of the as-prepared cathodes. The capacity retention of TiO 2 -coated porous electrodes is substantially improved compared to that of the pristine cathode material for high-temperature cycling. Electrochemical impedance spectroscopy confirms that the ALD-TiO 2 coating suppresses the undesired side reactions initiated at the electrode/electrolyte interface, reduces charge transfer resistance, and ultimately facilitates the Li + transport through the composite cathode nanostructure. The robust design of the ALD-TiO 2 cathode material enables high-temperature operation (>55 °C) with enhanced specific capacity, superior rate capability, excellent cyclability, and ultra-high coulombic efficiency within a wide potential window (3.0–4.35 V). Furthermore, the R2R ALD technique developed in this work paves the way for large-scale fabrication of ceramic-coated cathode sheets with a production rate reaching 2.4 m min –1 for a continuous coating operation.

25 ENERGY STORAGE↗

DOE OSTI2020

Atomic-scale tuned interface of nickel-rich cathode for enhanced electrochemical performance in lithium-ion batteries

The Ni-rich layered LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC6 22 ) is one promising cathode for lithium-ion batteries (LIBs), but suffers from poor cycling stability under high cutoff potentials. The performance degradation was reflected as capacity fading and voltage drop, having their roots in instable interface of NMC622. Aimed at improving interfacial stability, in this study, we deposited nanoscale ZrO 2 coatings conformally over NMC622 cathodes using atomic layer deposition (ALD). We found that, under a high cutoff voltage (4.5 V), the ALD ZrO 2 coatings evidently improved the performance of NMC622 cathode, showing better cyclability and higher sustainable capacity. In addition, the ALD coatings dramatically boosted the rate capability of NMC622. All these compelling performance results are ascribed to the atomic-scale tunable ZrO 2 coatings via ALD, which create stable interface and thereby inhibit unfavorable evolutions. In the study, we utilize a suite of characterization tools and various analyses to clarify the effects of ALD ZrO 2 coatings. This study will be helpful for improving the performance of nickel-rich cathodes via interfacial engineering using ALD.

25 ENERGY STORAGE↗

DOE OSTI2020

On electrolyte wetting through lithium-ion battery separators

The wettability by electrolyte is a critical characteristic of lithium-ion battery separators since electrolyte absorption is essential for ionic transport. Most importantly, fast absorption of electrolyte facilitates the electrolyte filling and wetting processes during the battery assembly. However, theoretical or experimental investigation of separator wettability has rarely been reported, and thus very little quantitative data can be found in the existing literature. Here, innovative experimental techniques and associated analytical models have been developed to fully characterize the electrolyte wetting behavior through battery separators. Both in-plane and through-plane imbibition processes are investigated. The results show that, electrolyte needs significantly longer time to wet separators than it does for commercial electrodes. The wetting rate depends significantly on the pore size, porosity, and micro-structure of the separators. Electrolyte in-plane wetting is only observed in the separators manufactured by the wet process. Increasing separator porosity and pore size is shown to be substantially increasing through-plane wetting rate. In addition, ceramic coating is shown to increase in-plane wetting but retard through-plane wetting.

25 ENERGY STORAGE↗

DOE OSTI2020

Aqueous Ni-rich-cathode dispersions processed with phosphoric acid for lithium-ion batteries with ultra-thick electrodes

Lithium-ion battery (LIB) production can benefit both economically and environmentally from aqueous processing. Although these electrodes have the potential to surpass electrodes conventionally processed with N -methyl-2-pyrrolidone (NMP) in terms of performance, significant issues still exist with respect to ultra-thick cathodes ($\gg$4 mAh/cm 2 areal capacities). A major concern for these types of electrodes with high-nickel active material stems from lithium leaching from active material, which drives the pH of the dispersion in excess of 12 and subsequently corrodes the current collector interface. As this corrosion reaction proceeds, hydrogen generation at the interface creates bubbles which cause severe cracking in the dried electrode surface. When areal loadings are increased, this effect becomes more pronounced and is detrimental to both mechanical and electrochemical properties of these electrodes. In this work, a technique for mitigating corrosion at the current collector by adjusting the pH of the dispersion with the addition of phosphoric acid is investigated. Phosphoric acid was added in 0.5 wt% increments between 0.0 and 1.5 wt%, and effects on rheology, adhesion, corrosion, and electrochemical performance were investigated. A technique is reported for producing aqueous processed cathodes with areal loadings of 6–8 mAh/cm 2 with reduced surface cracking and superior high-rate discharge capacity (i.e. high-power performance) for this class of cathode loadings.

25 ENERGY STORAGE↗

DOE OSTI2020

Operation, Manufacturing, and Supply Chain of Lithium-ion Batteries for Electric Vehicles

The US Department of Energy (DOE) has a rich history of funding key innovations in batteries through multiple programs, including the Energy Efficiency and Renewable Energy programs sponsored by the Vehicle Technologies Office and Advanced Manufacturing Office. These DOE-sponsored innovations have been critical in lowering the cost of lithium-ion batteries to less than $160/kWh and increasing their energy density to more than 250 Wh/kg, enhancing the nation’s electrification system and achieving higher degrees of decarbonization. These investments continue to be crucial for positioning the United States as the hub for the most cumulative battery R&D programs worldwide. However, major breakthroughs in battery manufacturing are still needed to enable an electrified future evolving to predominantly incorporate rechargeable lithium-ion batteries. This will require a strong battery manufacturing base that will not only enable cutting-edge advancements in materials and manufacturing sciences but will also allow the United States to become a world leader in this fast-growing area. This review aims at supporting DOE’s Advanced Technology Vehicle Manufacturing Loan Program to give technology background and information that can be used to develop the basis for loan topics and evaluate battery applications. Such a program can represent a significant stride toward reinforcing the US position in advanced manufacturing by introducing artificial intelligence, machine learning, and sensing and smart controls to facilitate, expedite, and lead the battery industry by 2030.

25 ENERGY STORAGE↗

DOE OSTI2020

Sustainable Direct Recycling of Lithium-Ion Batteries via Solvent Recovery of Electrode Materials

Separation of electrode materials from their current collectors is an enabling step toward recovering critical materials from spent lithium-ion batteries. In this study, a highly efficient, cost-effective, and environmentally sustainable separation process was developed for that purpose. Ethylene glycol, a vital commodity chemical as an antifreeze and polymer precursor, is used to delaminate electrode materials at low temperatures in seconds without altering the crystalline structure and morphology of active electrode materials. The recovered current collectors were intact without any corrosion. The authors also found that the solvent could be continuously reused, leading to the development of a closed-loop ecosystem and lithium-ion battery circular economy. The ultrafast delamination was driven by the competitive inhibition of binding through the weakening of hydrogen bonding. The ethylene glycol-based separation is a sustainable electrode recovery process that paves the way for battery recycling.

25 ENERGY STORAGE↗

DOE OSTI2020

Correlating the influence of porosity, tortuosity, and mass loading on the energy density of LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathodes under extreme fast charging (XFC) conditions

Extreme fast charging capabilities along with high energy density of Li-ion batteries are the key factors to increase the adoption of electric vehicles while eliminating the problem of range anxiety. The U.S Department of Energy has a goal of <12 min charging time with energy density of > 200 Wh kg -1 . A combined improvement in the electrode architecture, electrolyte properties, and separator membrane is necessary to achieve this goal. Cells with thin electrodes are capable of extreme fast charging at the expense of low energy density and high cost. Electrode engineering can maximize energy density. In this work, the influence of porosity, mass loading and charging protocols on capacity and energy density and electrode kinetics are investigated under extreme fast charging conditions. Increasing the mass loading from 11.5 mg cm -2 to 25 mg cm -2 compromises the rate performance due to the mass transport limitation and underutilization of thick electrodes. Furthermore, reducing the electrode porosity from 50% to 35% improves the rate performance ascribed to shorter Li ion diffusion length. Symmetric cells are cycled to verify the performance of the half cells, suggesting that Li metal plating is the rate limiting step under high current density.

25 ENERGY STORAGE↗

DOE OSTI2020

Direct Recycling of Spent NCM Cathodes through Ionothermal Lithiation

Ionic liquids (ILs) are a family of nonconventional molten salts that offer many advantages, such as negligible vapor pressures, negligible flammability, wide liquidus ranges, good thermal stability, and much synthesis flexibility. The unique solvation environment of these ILs provides new reaction or flux media for controlling formation of solid-state materials with a minimum perturbation of morphologies. A successful lithiation via ionothermal synthesis using a cost-effective Li halide as Li source and recyclable ILs as solvents is reported in this study for the direct recycling of LiNi 1/3 Co 1/3 Mn 1/3 O 2 (NCM 111) cathodes. In addition, the ionic liquids can be readily recycled and reused after ionothermal lithiation. The lithiation of spent cathodes can enable the direct recycling of spent cathode materials in lithium-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2020

Improved lithium storage capacity and high rate capability of nitrogen-doped graphite-like electrode materials prepared from thermal pyrolysis of graphene quantum dots

Adopting a solid-phase microwave-assisted technique followed by thermal pyrolysis of N-functionalized graphene quantum dots, novel nitrogen-doped graphite-like (NGL) electrode materials were synthesized in this work and served as the anode for Li-ion batteries. The NGL anode demonstrated reversible capacity of 530 mAh g -1 at 0.1C, superior rate capability at high C rate operation (420 mAh g -1 at 5C), remarkable initial coulombic efficiency (>95.7%), and excellent cyclic stability along with high efficiency (>99.1%) during entire cycling. The NGL anode nanostructure enables improved lithium ion mobility and reversible Li + storage during cycling. The analysis of the Ragone plots revealed that the specific energy of NGL anode reaches to ca. 840 Wh kg -1 at the power density of 4200 W kg -1 . The diffusion coefficient of Li ions was measured as 1.69 × 10 -9 cm 2 s -1 for the NGL anode material, substantially improving over commonly used graphite electrodes (15–26 times higher Li + diffusivity). The high-rate cyclability as well as the cyclic stability of the NGL anodes were also confirmed via long-term cycling of full pouch cells assembled with ternary cathode and NGL anode. The robust design of the NGL anode materials introduced in this work, paves the way for designing next-generation lithium-ion batteries operating at ultra-high C rates.

25 ENERGY STORAGE↗

DOE OSTI2020

Batch and continuous methods for evaluating the physical and thermal properties of films

Thermal methods and systems are described for the batch and/or continuous monitoring of films and/or membranes and/or electrodes produced in large-scale manufacturing lines. Some of the methods described include providing an energy input into a film, measuring a thermal response of the film, and correlating these to one or more physical properties and/or characteristics of the film.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

Eutectic Synthesis of the P2-Type Na x Fe 1/2 Mn 1/2 O 2 Cathode with Improved Cell Design for Sodium-Ion Batteries

An engaging area of research in sodium-ion batteries (SIBs) has been focusing on discovery, design, and synthesis of high-capacity cathode materials in order to boost energy density to levels close enough to that of state-of-the-art lithium-ion batteries. Of particular interest, P2-type layered oxide, Na 2/3 Fe 1/2 Mn 1/2 O 2 , has been researched as a potential cathode in SIBs based on its high theoretical capacity of 260 mA h/g and use of noncritical materials. However, the reported synthesis methods are not only complex and energy-demanding but also often yield inhomogeneous and impure materials with capacities less than 200 mA h/g under impractical test conditions. Here, we report a novel synthesis route using low-temperature eutectic reaction to produce highly homogeneous, crystalline, and impurity-free P2-Na x Fe 1/2 Mn 1/2 O 2 with enhanced Na-ion diffusivity and kinetics. The overall electrochemical performances of the Na-ion cells have been improved by pairing the P2-cathode with presodiated hard carbon anodes, leading to reversible capacities in the range of 180 mA h/g. This new approach is a contribution toward the simplification of synthesis and scalability of sodium-based cathodes with high crystallinity and fine-tuned morphology and the realization of a sodium-ion battery system with lower cost and improved electrochemical performance.

25 ENERGY STORAGE↗

DOE OSTI2020

Perspectives on the relationship between materials chemistry and roll-to-roll electrode manufacturing for high-energy lithium-ion batteries

As lithium-ion battery (LIB) active material and cell manufacturing costs continue to drop with wider adoption of electric vehicles, electrode and cell processing costs remain too high in terms of reaching the ultimate U.S. Department of Energy (DOE) cell cost target of $80/kWh. This paper primarily covers major materials chemistry advancements made over the last 10 years at Oak Ridge National Laboratory (ORNL) in the space of advanced manufacturing science for LIBs with the aim of simultaneously meeting the ultimate cost target, 500 Wh/kg gravimetric energy density, 10-15-min fast charge times, and 1000 deep discharge cycles. Aqeous electrode processing with a variety of active anode and cathode materials is now a standard procedure at the DOE Battery Manufacturing R&D Facility at ORNL (BMF), including the latest processes developed for Ni-rich cathodes. New results on cobalt-free LiNi 0.8 Fe 0.1 Al 0.1 O 2 (NFA 811) are also included and discussed in an electrode processing advantage context. In addition, colloidal processing advancements have been made for Si/C composite anodes for achieving >600 mA h/g capacities. Optimization of electrode coating parameters and drying protocols have been completed, which has elucidated how key processing variables need to be changed when parameters such as slurry solids loading, solvent type, and wet electrode thickness are changed. ORNL has also increased the line speeds at which thick cathodes can be processed using ultra-fast electron beam (EB) curing and substantially decreased formation cycling times to <1 day. Finally, key details of these advancements are discussed in the context of materials chemistry and process-property-performance relationships.

25 ENERGY STORAGE↗

DOE OSTI2020

Batteries Annual Progress Report (FY2019)

The Vehicle Technologies Office (VTO) of the Department of Energy (DOE) conducts research and development (R&D) on advanced transportation technologies that would reduce the nation’s use of imported oil and would also lead to reductions in harmful emissions. Technologies supported by VTO include electric drive components such as advanced energy storage devices (primarily batteries), power electronics and electric drive motors, advanced structural materials, energy efficient mobility systems, advanced combustion engines, and fuels. VTO is focused on funding early-stage high-reward/high-risk research to improve critical components needed for more fuel efficient (and cleaner-operating) vehicles. One of the major VTO objectives is to enable U.S. innovators to rapidly develop the next generation of technologies that achieve the cost, range, and charging infrastructure necessary for the widespread adoption of plug-in electric vehicles (PEVs). An important prerequisite for the electrification of the nation’s light duty transportation sector is development of more cost-effective, longer lasting, and more abuse-tolerant PEV batteries. One of the ultimate goals of this research, consistent with the current vehicle electrification trend, is an EV which can provide the full driving performance, convenience, and price of an internal combustion engine (ICE) vehicle. To achieve this, VTO has established the following overarching goal (Source: FY2021 Congressional Budget Justification1): …identify new battery chemistry and cell technologies with the potential to reduce the cost of electric vehicle battery packs by more than half, to less than $100/kWh (ultimate goal is $60/kWh battery cell cost), increase range to 300 miles, and decrease charge time to 15 minutes or less by 2028. VTO works with key U.S. automakers through the United States Council for Automotive Research (USCAR) – an umbrella organization for collaborative research consisting of Fiat Chrysler Automobiles (FCA), the Ford Motor Company, and General Motors. Collaboration with automakers through the partnership known as U.S. Driving Research and Innovation for Vehicle Efficiency and Energy Sustainability (U.S. DRIVE) attempts to enhance the relevance and the success potential of its research portfolio. VTO competitively selects projects for funding through funding opportunity announcements (FOAs). Directly-funded work at the national laboratories are awarded competitively through a lab-call process. During the past year, VTO continued R&D in support of PEVs. Stakeholders for VTO R&D include universities, national laboratories, other government agencies and industry (including automakers, battery manufacturers, material suppliers, component developers, private research firms, and small businesses). This document summarizes the progress of VTO battery R&D projects supported during the fiscal year 2019 (FY 2019).

25 ENERGY STORAGE↗

DOE OSTI2020

Corrosion Mitigation and Increased Discharge Capacity in Aqueous Processed Thick Cathodes using Phosphoric Acid Additives

Aqueous processed cathodes for lithium-ion batteries are favorable for both cost and environmental reasons; however, these electrodes still face significant problems with increasing areal capacities (i.e. thickness). Highly basic slurry conditions (pH in excess of 12) corrode the current collector surface and evolve hydrogen gas. Consequently, bubbling at the electrode interface causes substantial damage to the dried electrode. As the loading of these electrodes is increased, damage becomes severe and results in lack of adhesion and cohesion. Here introduction of phosphoric acid to combat the rise in pH and suppress the corrosion at the current collector surface is investigated. Phosphoric acid was added in increments of 0.5, 1.0, and 1.5 wt% and the subsequent effects on slurry rheology, particle size, adhesion, and electrochemical cycling were investigated. A technique is reported for obtaining thick (6-8 mAh/cm2) cathodes that exhibit reduced surface cracking and improved rate performance as compared to control samples.

Kukay, Alexander↗

DOE OSTI2020

Enabling high rate capability, low internal resistance, and excellent cyclability for vanadium redox flow batteries utilizing ultrafast laser-structured graphite felt

The electrochemical performance of vanadium redox flow batteries (VRFBs) was enhanced via laser-patterned graphite felt (GF) electrodes. The laser-structured GF electrodes engineered via preparing a series of well-ordered microscopic channel structures with an average width of 200 μm, creating a three-dimensional carbon framework. The ultrafast laser patterning increased the porosity by 10%, as compared to pristine electrode. The analysis of the overpotential distribution using electrochemical impedance spectroscopy revealed that the electrode polarization involving charge transfer and diffusion resistance is strongly alleviated with the aid of carbon micro-perforation. The advanced design of laser-structured GF electrode also exhibits high rate capability, low internal resistance, and excellent cyclability. The improved performance was attributed to the synergistic effect involving (i) high electrochemically active surface area for rapid electrochemical reactions (i.e., V(II)/V(III) and V(IV)/V(V) redox couples) and (ii) excellent transport properties for facile electron/ion/species transport. The micro-scale channels created with the laser-ablation technique act as capillary structures and enabled homogeneous and rapid wetting of GF electrodes as formulated with the classical Washburn equation. The VRFB equipped with the laser-structured GF electrodes delivered a high discharge capacity with exceptional capacity retention upon extended cycling (>84.9%). In conclusion, accordingly, the design of laser-structured electrode paves the pathway towards finely tuning the electrode internal microstructure for improved cyclability, durability, and capacity retention in various electrochemical energy storage/conversion devices (e.g. all-vanadium redox flow batteries).

25 ENERGY STORAGE↗

DOE OSTI2020

Manufacturing of thick composite electrode using solvent mixtures

A method of making an electrode includes the step of dispersing an active electrode material and a conductive additive in a solvent to create a mixed dispersion. The solvent has a surface tension less than 40 mN/m and an ozone forming potential of no more than 1.5 lbs. ozone/lb. solvent. A surface of a current collector is treated to raise the surface energy of the surface to at least the surface tension of the solvent or the mixed dispersion. The dispersed active electrode material and conductive additive are deposited on the current collector. The coated surface is heated to remove solvent from the coating.

25 ENERGY STORAGE↗

DOE OSTI2020

Observation of Ion Electrosorption in Metal–Organic Framework Micropores with In Operando Small-Angle Neutron Scattering

A molecular-level understanding of transport and adsorption mechanisms of electrolyte ions in nanoporous electrodes under applied potentials is essential to control the performance of double-layer capacitors. In this paper, in operando small-angle neutron scattering (SANS) is used to directly detect ion movements into the nanopores of a conductive metal–organic framework (MOF) electrode under operating conditions. Neutron-scattering data reveals that most of the void space within the MOF is accessible to the solvent. Upon the addition of the electrolyte sodium triflate (NaOTf), the ions are adsorbed on the outer surface of the protrusions to form a 30 Å layer instead of entering the ionophobic pores in the absence of an applied charging potential. The changes in scattering intensity when potentials are applied suggests the ion rearrangement in the micropores following different mechanisms depending on the electrode polarization. These observations shed insights on ion electrosorption in electrode materials.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Towards Understanding of Cracking during Drying of Thick Aqueous-Processed LiNi 0.8 Mn 0.1 Co 0.1 O 2 Cathodes

Replacing N-methyl-2-pyrrolidone (NMP) with water for processing of lithium-ion battery (LIB) electrodes has both cost and environmental benefits, which include reduced drying time, lower dryer capital cost, elimination of NMP recovery capital equipment, and no release of volatile organic compounds (VOCs) into the environment. However, aqueous-processed thick cathodes (≳4 mAh/cm 2 ) typically exhibit detrimental cracking during drying that is not observed for the NMP-based counterpart. The reasons for cracking of these water-based thick electrodes are still not well understood due to the complex nature of the colloidal dispersions used in the LIB electrode processing steps. In this work, the contributions of various factors responsible for cracking are discussed. We show that eliminating hydrogen evolution due to corrosion of the aluminum current collector eliminated the majority of the cracks regardless of the coating thickness, identifying the gas evolution as the primary reason for electrode cracking. Some secondary cracks and pinhole-type defects remained after addressing the aluminum current collector corrosion, which are thought to be caused by an inferior binding network formed by carbon black and binder in aqueous-processed cathodes compared to those processed with NMP. The thick aqueous processed cathodes are not able to sufficiently withstand the drying stresses without crack formation. We demonstrate reduction of these secondary defects by either improving the binding network or by reducing the drying stress. The former was achieved by replacing carbon black with vapor grown graphite tubes (VGGTs) that caused a more efficient utilization of the emulsion binder. Here, the latter was achieved by adding a small amount of IPA as a co-solvent that has been shown to reduce capillary stresses.

25 ENERGY STORAGE↗