Search NASA⌕ Search

Engineering topics

Li, L.

Publications and source records attributed to Li, L..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Measurement of scintillation response of CsI[Na] to low-energy nuclear recoils by COHERENT

Here, we present results of several measurements of CsI[Na] scintillation response to 3–60 keV energy nuclear recoils performed by the COHERENT collaboration using tagged neutron elastic scattering experiments and an endpoint technique. Earlier results, used to estimate the coherent elastic neutrino-nucleus scattering (CEvNS) event rate for the first observation of this process achieved by COHERENT at the Spallation Neutron Source (SNS), have been reassessed. We discuss corrections for the identified systematic effects and update the respective uncertainty values. The impact of updated results on future precision tests of CEvNS is estimated. We scrutinize potential systematic effects that could affect each measurement. In particular we confirm the response of the H11934-200 Hamamatsu photomultiplier tube (PMT) used for the measurements presented in this study to be linear in the relevant signal scale region.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Atmospheric Radiative and Oceanic Biological Productivity Responses to Increasing Anthropogenic Combustion‐Iron Emission in the 1850–2010 Period

Abstract Anthropogenic emission is an important component of the present‐day iron cycle yet its long‐term impacts on climate are poorly understood. Iron mineralogy strongly affects its radiative and oceanic interactions and was unrepresented in previous studies. We perform simulations using a mineralogy‐based inventory and an atmospheric transport model and estimate the 1850–2010 global mean direct radiative forcing (DRF) to be +0.02 to +0.10 W/m 2 . We estimate that the CO 2 sequestration of 0.2–13 ppmv over the last 150 years due to enhanced phytoplankton productivity by anthropogenic iron deposition causes an avoided CO 2 forcing of −0.002 to −0.16 W/m 2 . While globally small, these impacts can be higher in specific regions; the anthropogenic DRF is +0.5 W/m 2 over areas with more coal combustion and metal smelting, and anthropogenic soluble iron sustains >10% of marine net primary productivity in the high‐latitude North Pacific Ocean, a region vulnerable to stratification due to climate change.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

The Optical Two- and Three-dimensional Fundamental Plane Correlations for Nearly 180 Gamma-Ray Burst Afterglows with Swift/UVOT, RATIR, and the Subaru Telescope

Gamma-ray bursts (GRBs) are fascinating events due to their panchromatic nature. We study optical plateaus in GRB afterglows via an extended search into archival data. We comprehensively analyze all published GRBs with known redshifts and optical plateaus observed by many ground-based telescopes (e.g., Subaru Telescope, RATIR) around the world and several space-based observatories such as the Neil Gehrels Swift Observatory. We fit 500 optical light curves, showing the existence of the plateau in 179 cases. This sample is 75% larger than the previous one, and it is the largest compilation so far of optical plateaus. We discover the 3D fundamental plane relation at optical wavelengths using this sample. This correlation is between the rest-frame time at the end of the plateau emission, ${T}_{\mathrm{opt}}^{* }$, its optical luminosity, L opt , and the peak in the optical prompt emission, L peak,opt , thus resembling the three-dimensional (3D) X-ray fundamental plane (the so-called 3D Dainotti relation). We correct our sample for redshift evolution and selection effects, discovering that this correlation is indeed intrinsic to GRB physics. We investigate the rest-frame end-time distributions in X-rays and optical (${T}_{\mathrm{opt}}^{* }$, ${T}_{{\rm{X}}}^{* }$), and conclude that the plateau is achromatic only when selection biases are not considered. We also investigate if the 3D optical correlation may be a new discriminant between optical GRB classes and find that there is no significant separation between the classes compared to the Gold sample plane after correcting for evolution.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Quasi-linear toroidal simulations of resonant magnetic perturbations in eight ITER H-mode scenarios

Abstract Both linear and quasi-linear aspects of the plasma response to the resonant magnetic perturbation (RMP) field are numerically investigated for various H-mode scenarios in ITER, covering the pre-fusion power operation and the fusion power operation phases. Linear response computations for eight ITER scenarios, with varying plasma current and toroidal magnetic field, reveal that the best coil current phasing for controlling the type-I edge localized modes (ELMs) scales roughly linearly with the edge safety factor. The coil phasing is defined as the relative toroidal phase of the coil currents between different rows, for a given toroidal harmonic. Quasi-linear initial value simulation, which is the focus of the present study, shows that application of the n = 3 ( n is the toroidal mode number) RMP field has a minimum side effect on the plasma core momentum confinement but potentially a large effect on the global particle transport. Generally, the RMP field with the best (worst) coil phasing for ELM control produces the strongest (weakest) effect on the plasma edge flow and the overall density. This robustly holds for all eight ITER scenarios. Consequently, in order to minimize the RMP induced side effects while achieving ELM control (suppression) in ITER, a compromise is necessary in choosing the coil current configuration.

Physics↗
DOE OSTI2022

Characterization of muon and electron beams in the Paul Scherrer Institute PiM1 channel for the MUSE experiment

The MUon Scattering Experiment, MUSE, at the Paul Scherrer Institute, Switzerland, investigates the proton charge radius puzzle, lepton universality, and two-photon exchange, via simultaneous measurements of elastic muon-proton and electron-proton scattering. The experiment uses the PiM1 secondary beam channel, which was designed for high precision pion scattering measurements. We review the properties of the beam line established for pions. We discuss the production processes that generate the electron and muon beams, and the simulations of these processes. Simulations of the π/μ/e beams through the channel using TURTLE and G4beamline are compared. The G4beamline simulation is then compared to several experimental measurements of the channel, including the momentum dispersion at the intermediate focal plane and target, the shape of the beam spot at the target, and timing measurements that allow the beam momenta to be determined. Finally, we conclude that the PiM1 channel can be used for high precision π, μ, and e scattering.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Non-linear MHD modelling of edge localized modes suppression by resonant magnetic perturbations in ITER

Edge localized modes (ELMs) suppression by resonant magnetic perturbations (RMPs) was studied with the non-linear magneto-hydro-dynamic (MHD) code JOREK for the ITER H-mode scenarios at 15 MA, 12.5 MA, 10 MA/5.3 T. In this study, the main aim was to demonstrate that ELMs can be suppressed by RMPs while the divertor 3D footprints of heat and particle fluxes remain within divertor material limits. The unstable peeling–ballooning modes responsible for ELMs without RMPs were modelled first for each scenario using numerically accessible parameters for ITER. Then the stabilization of ELMs by RMPs was modelled with the same parameters. RMP spectra, optimized by the linear MHD MARS-F code, with main toroidal harmonics N = 2, N = 3, N = 4 have been used as boundary conditions of the computational domain of JOREK, including realistic RMP coils, main plasma, scrape off layer (SOL) divertor and realistic first wall. The model includes all relevant plasma flows: toroidal rotation, two fluid diamagnetic effects and neoclassical poloidal friction. With RMPs, the main toroidal harmonic and the non-linearly coupled harmonics remain dominant at the plasma edge, producing saturated modes and a continuous MHD turbulent transport thereby avoiding ELM crashes in all scenarios considered here. The threshold for ELM suppression was found at a maximum RMP coils current of 45 kAt–60 kAt compared to the coils maximum capability of 90 kAt. In the high beta poloidal steady-state 10 MA/5.3 T scenario, a rotating QH-mode without ELMs was observed even without RMPs. In this scenario with RMPs N = 3, N = 4 at 20 kAt maximum current in RMP coils, similar QH-mode behaviour was observed however with dominant edge harmonic corresponding to the main toroidal number of RMPs. The present MHD modelling was limited in time by few tens of ms after RMPs were switched on until the magnetic energy of the modes saturates. As a consequence the thermal energy was still evolving on this time scale, far from the ITER confinement time scale and hence only the form of 3D footprints on the divertor targets can be indicated within this set-up. Also note, that the divertor physics was missing in this model, so realistic values of fluxes are out of reach in this modelling. However the stationary 3D divertor and particle fluxes could be simply extrapolated from these results to the stationary situation considering that a large power fraction should be radiated in the core and SOL and only about 50 MW power is going to the divertor, which is an arbitrary, but reasonable number used here. The 3D footprints with RMPs show the characteristic splitting with the main RMP toroidal symmetry. The maximum radial extension of the footprints typically was ~20 cm in inner divertor and ~40 cm in outer divertor with stationary heat fluxes decreasing further out from the initial strike point from ~5 MW m ₋2 to ~1 MW m ₋2 assuming a total power in the divertor and walls is 50 MW. The heat fluxes remain within the divertor target and baffle areas, however with rather small margin in the outer divertor which could be an issue for the first wall especially in transient regimes when part of the plasma thermal energy is released due to switching on the RMP coils. This fact should be considered when RMPs are applied with a more favorable application before or soon after the L–H transition, although optimization is required to avoid increasing the L–H power threshold with RMPs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Loss of energetic particles due to resistive wall mode instability in ITER

Effects of an unstable n = 1 (n is the toroidal mode number) resistive wall mode (RWM) on the energetic particle (EP) confinement and loss are numerically investigated, for an ITER steady state scenario with 10 MA plasma current and 5.3 T toroidal field. The eigenfunction of the RWM is computed, with the associated three-dimensional magnetic field perturbation superposed with the 2D equilibrium field for tracing the EP drift orbits. Considered are mono-energetic EPs at 0.5 MeV and 1 MeV for deuterium ions, and 3.5 MeV for fusion-born alphas, with a range of distribution in the particle pitch angle. Modeling finds that less than 20% of EPs can be lost to the limiting surface in ITER assuming a source distribution uniform in minor radius, due to an unstable RWM that produces 100 Gauss poloidal field perturbation at the outboard mid-plane just inside the (effective) resistive wall surface. On top of the initial prompt drift orbit loss for counter-current EPs, the RWM induced particle loss occurs on a one second time scale, which is comparable to the RWM growth time in ITER. The 'wetted' area, due to the lost EPs striking the limiting surface, is generally found to be large due to the RWM. This is a favorable prediction for ITER. Here, the loss distribution in the poloidal angle is more uniform for co-current EPs. Counter-current EPs experience outward orbit drift when launched from the low-field side, and tend to more often hit the bottom region of the limiting surface.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Monitoring the SNS basement neutron background with the MARS detector

Here, we present the analysis and results of the first dataset collected with the MARS neutron detector deployed at the Oak Ridge National Laboratory Spallation Neutron Source (SNS) for the purpose of monitoring and characterizing the beam-related neutron (BRN) background for the COHERENT collaboration. MARS was positioned next to the COH-CsI coherent elastic neutrino-nucleus scattering detector in the SNS basement corridor. This is the basement location of closest proximity to the SNS target and thus, of highest neutrino flux, but it is also well shielded from the BRN flux by infill concrete and gravel. Furthermore, these data show the detector registered roughly one BRN per day. Using MARS' measured detection efficiency, the incoming BRN flux is estimated to be 1.20 ± 0.56 neutrons/m 2 /MWh for neutron energies above ~3.5 MeV and up to a few tens of MeV. We compare our results with previous BRN measurements in the SNS basement corridor reported by other neutron detectors.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Quenching factor measurements of neon nuclei in neon gas

The NEWS-G collaboration uses spherical proportional counters (SPCs) to search for weakly interacting massive particles (WIMPs). Here, in this paper, we report the first measurements of the nuclear quenching factor in neon gas at 2 bar using an SPC deployed in a neutron beam at the TUNL facility. The energy-dependence of the nuclear quenching factor is modeled using a simple power law: $αE^{β}_{nr}$; we determine its parameters by simultaneously fitting the data collected with the detector over a range of energies. We measured the following parameters in Ne : CH 4 at 2 bar: α= 0.2801±0.0050 (fit) ±0.0045 (sys) and β=0.0867±0.020 (fit) ±0.006 (sys). Our measurements do not agree with expected values from SRIM or Lindhard theory. We demonstrated the feasibility of performing quenching factor measurements at sub-keV energies in gases using SPCs and a neutron beam.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Corrosion characteristics of Mo and TZM alloy for plasma facing components in molten lithium at 623 K

Here, in this study, the corrosion behaviours of molybdenum (Mo) and a Mo-based alloy (TZM) were investigated using a static immersion corrosion technique. Weight loss, surface microstructure, and corrosion depth of Mo and the TZM alloy were correlated with elements. The compatibility of Mo and the TZM alloy in static liquid Li was suitable. Mo demonstrated uniform corrosion with a homogenous dissolution of free C and Mo, and TZM alloy exhibited a nonuniform corrosion behaviour with a preferential grain boundary attack caused by the selective dissolution of free C, Ti, and Zr. When the surface oxidation layer of the samples was consumed, free C from Mo and TZM diffused into molten Li to form Li 2 C 2 and then was captured by Zr, Ti, and Mo to form thermodynamically stable carbides, which resulted in the enrichment of the C layer near the sample surfaces. In addition, Ti and Zr acted as N-trappers in liquid Li; the formation of Zr and Ti nitrides resulted in the enrichment of N, Ti, and Zr elements on the surface and led to TZM corrosion increase. Thus, Zr and Ti depletion, pitting, and grain boundary corrosion were problematic for TZM under long-term exposure to liquid Li. Reducing the content of free C and nonmetallic N and increasing the amount of Ti and Zr carbides on the surface of and inside the raw TZM alloy helped improve the corrosion resistance of TZM in liquid Li.

36 MATERIALS SCIENCE↗