Comprehending interface shearing behavior within a bulk Cu-Nb alloy using micromechanical testing
Not Available
Ajantiwalay, Tanvi↗
Engineering topics
Li, Lei
Publications and source records attributed to Li, Lei.
Towards stabilization of pressurized oxy-coal diffusion flames
Designing an effective burner is vital for the development of pressurized oxy-fuel combustion technologies. Turbulent jet diffusion burners are adopted for the pressurized oxy-combustor in this research and a bluff-body is employed to create a recirculation zone to stabilize the flame in pressurized oxy-combustor. The objective of this numerical work is to perform a systematic analysis of the characteristics of this pressurized non-premixed flame. Specifically, a 15-bar POFC combustor of power 100 kWth is modeled employing the Ansys FLUENT commercial platform, using Reynolds-averaged Navier-Stokes (RANS) modeling. The present computational work focuses on identifying the aerothermodynamic features of the isothermal and reacting flow with a disk-shape bluff-body. Results show that fuel-oxidizer stream momentum ratio has great impacts on the temperature profile of the down-fired, co-axial, pressurized oxy-coal, diffusion flame. Parametric study of the width of the burner tip identifies an optimal range for this pressurized burner.
Li, Lei↗
Dynamic data-driven multiscale modeling for predicting the degradation of a 316L stainless steel nuclear cladding material
Here, we have developed a long short-term memory stacked ensemble (LSTM-SE) surrogate modeling approach that can provide rapid predictions of microstructural evolution and the resultant mechanical properties of American Iron and Steel Institute (AISI) 316L series stainless steel (316LSS) fuel cladding under conditions of varying temperature and radiation dose rate. To acquire training data, we developed and implemented a kinetic Monte Carlo (KMC) model to simulate precipitation kinetics of M 23 C 6 , γ', and G phases within SS316L cladding. Experimentally reported precipitation kinetics of SS316L in literature were linked to the kinetic parameters of the simulated precipitation in our KMC model. The model was then used to simulate microstructure evolution under synthetically generated treatments of varying temperature and radiation dose rate, for periods of up to 3000 hours. Changes in volume fraction, number density, and particle size of precipitates were recorded, and particle area fractions were correlated using statistical methods to develop the surrogate model. Simultaneously, the mechanical properties of the simulated microstructures were evaluated using microstructure-based finite element method (FEM) analysis to determine the elastic modulus, yield stress, ultimate tensile strength, and elongation to failure of the aged microstructures. Using this approach, our surrogate model can predict precipitation behavior within 0.25% volume fraction and mechanical properties within 6% relative error from the values predicted by the KMC and FEM models using 50 training simulations as input. The trained recurrent neural network-based model can return estimations of precipitation kinetics and mechanical properties ~1000 times faster than the physics-based codes. This work demonstrates, as a proof of concept, that reactor material service lifetimes under variable service conditions can be predicted for a statistics-based model from a practicably obtainable dataset.
36 MATERIALS SCIENCE↗
Impact of a Bluff Body on a Pressurized Oxy-fuel Flame
Designing an effective burner is vital for the development of pressurized oxy-fuel combustion technologies. In the present work, turbulent jet diffusion burners are adopted for a pressurized oxy-combustor, with a bluff-body employed to create a recirculation zone, thereby stabilizing the flame in such a combustor. The objective of this numerical study is to perform a systematic analysis of the characteristics of such a pressurized non-premixed flame. Specifically, a 15-bar pressurized oxy-fuel combustor of power 100 kWth is modeled by means of the Ansys FLUENT commercial platform, using the Reynolds-averaged Navier-Stokes (RANS) approach. The present work focuses on identifying the aerothermodynamic features of the pressurized oxy-fuel burner with a disk-shape bluff-body. It is shown that the fuel-to-oxidizer stream momentum ratio has a great impact on the temperature profile of the down-fired, co-axial, pressurized oxy-coal, diffusion flame. A parametric study of the blockage ratio of the burner identifies an optimal range for this pressurized burner.
Li, Lei↗
Temperature-dependent iron motion in extremophile rubredoxins – no need for ‘corresponding states’
Extremophile organisms are known that can metabolize at temperatures down to – 25 °C (psychrophiles) and up to 122 °C (hyperthermophiles). Understanding viability under extreme conditions is relevant for human health, biotechnological applications, and our search for life elsewhere in the universe. Information about the stability and dynamics of proteins under environmental extremes is an important factor in this regard. Here we compare the dynamics of small Fe-S proteins – rubredoxins – from psychrophilic and hyperthermophilic microorganisms, using three different nuclear techniques as well as molecular dynamics calculations to quantify motion at the Fe site. The theory of ‘corresponding states’ posits that homologous proteins from different extremophiles have comparable flexibilities at the optimum growth temperatures of their respective organisms. Although ‘corresponding states’ would predict greater flexibility for rubredoxins that operate at low temperatures, we find that from 4 to 300 K, the dynamics of the Fe sites in these homologous proteins are essentially equivalent.
59 BASIC BIOLOGICAL SCIENCES↗
Investigation of Thermal Radiation under Pressurized Oxy-combustion Conditions
Thermal radiation of the gaseous and particle phases in a pilot-scale pressurized oxy-combustor is computationally studied. In particular, the radiation characteristics of gases and particles are estimated by employing the statistical narrow-band model and the large-particle model. It is found that thermal radiation of the particle cloud dominates in the combustor under a furnace temperature of 1500 K and when there is no substantial loss of particles to the walls. Another important observation is that radiation from the gas and particles can be approximately treated as a graybody under these conditions. More specifically, the results on the spectral radiation intensity of a gas comprising 40% (vol) H 2 O and 60% CO 2 show that when the pressure is increased to 15 bar, and the radiation pathlength is 100 cm, the spectral radiation profile of the gas phase approaches that of a blackbody at the respective temperature. In addition, the emissivity of the particulate cloud has been evaluated as a function of the particle concentration and diameter by employing the large-particle model. It is shown that the emissivity grows with the particle concentration but decreases with the particle size for the same mass of the particles. Finally, this outcome of the present study is expected to be used to validate the assumption of the gray-gas model adopted in the numerical simulations of pressurized oxy-combustion.
large-particle model↗
Exceptional strength and wear resistance in an AA7075/TiB 2 composite fabricated via friction consolidation
The friction consolidation method successfully reinforced aluminum 7075 alloy (AA7075) with high-volume fractions (12 and 24 vol%) of titanium diboride (TiB 2 ) by high pressure and severe plastic deformation at elevated temperatures. The consolidated AMCs have a uniform dispersion of submicron- and micron-sized TiB 2 particles in the AA7075 matrix, with significant refinement of the matrix grain size and the particles. The addition of TiB 2 significantly increases hardness by up to 50 %, Young’s modulus by up to 62 %, and ultimate tensile strength by up to 28 % to 672 MPa, while reducing ductility by 80 %. Wear resistance of 7075/24 vol% TiB 2 improves seven-fold compared to baseline, making it comparable to that of carburized steels. Microstructure-based finite element modeling provided a theoretical strength limit of ~730 MPa for the composites and indicated that high triaxiality in conjunction with severe equivalent plastic strain in a narrow area between the TiB 2 particles led to early fracture initiations, limiting the ductility.
36 MATERIALS SCIENCE↗
Large eddy simulation of a pressurized reactive fluid–particle system: single-particle dynamics analysis
Pressurized oxy-combustion (POC) is a promising candidate to reduce carbon emissions in power generation. Designing an effective burner plays a vital role in developing new combustion technologies. Because of the high pressure, the volume fraction of particles in a pressurized oxy-combustor could be higher than that in the conventional combustor, therefore, the particle dynamics in the pressurized vessel need to be evaluated accordingly. The present computational work is to predict the influence of the particle size and particle injection location on the particle trajectory. The Stokes number based on turbulence fluctuation, St, is adopted to evaluate the impact of the gas phase on the particulate phase. A large eddy simulation (LES) with the environment pressure of 15 bar and the thermal input of the fuel particle of 100 kWth has been performed by means of the commercial CFD package. It is shown that that in this pressurized environment St << 1 for the 25 µm particles, St ~ 1 for the 100 µm particles, while for the particles exceeding 200 µm St >> 1. The trajectories of the sampling particles from the LES results support this conclusion: the particles less than 100 µm tend to be uniformly distributed in the space while the particles exceeding 200 µm tend to concentrate in the combustor.
Li, Lei↗
Large eddy simulation of particle dispersion analysis in a pressurized reactive fluid–particle system
Pressurized oxy-combustion (POC) is a promising candidate to reduce carbon emissions in power generation. Designing an effective burner plays a vital role in developing new combustion technologies. Because of high pressure, the volumetric fraction of particles in a pressurized oxy-combustor could be higher than that in the conventional combustor, consequently, the particle dynamics in the pressurized vessel need to be evaluated accordingly. Specifically, the present computational work analyzes the pattern of the particle dispersion by extracting the particle mass flow rate and the particle size distribution in the pressurized combustor. A large eddy simulation (LES) with the environment pressure 15-bar and 100 kWth thermal input of fuel particle has been performed. The particle mass flow rates sampled in several cross-section planes strongly fluctuate, indicating the impacts of the flame as well as the gas-phase flow on the particle movement. Animations of the particle-gas flow show that the flow recirculation plays a major role in producing the pulsing phenomenon of the particle mass flow rate.
Li, Lei↗
Meshfree Process Modeling and Experimental Validation of Friction Riveting of Aluminum 5052 to Aluminum 6061
Friction riveting (Fric-riveting) is an innovative, fast, and energy-efficient process for spot-joining metal-metal structures. Although fric-riveting has been studied experimentally in recent years, its process modeling is rarely found in the literature primarily because of the associated large material deformation, extreme thermomechanical conditions, and complex contact conditions. In this work, a mesh-free smoothed particle hydrodynamics (SPH) framework that can well handle the abovementioned numerical challenges is used to simulate the fric-riveting of AA5052 to AA6061. Predicted material morphology, multi-point temperatures, and plunge force are thoroughly validated by experimental observations. The material severe plastic deformation zone in the vicinity of the riveting zone is further predicted by the SPH model, which indicates the material mixing and potential grain refinement zone. Based on the validated model, process parameters can be optimized which yields better performance over the baseline case.
Friction riveting (fric-riveting), Smoothed partic↗
Epitopes recognition of SARS-CoV-2 nucleocapsid RNA binding domain by human monoclonal antibodies
Coronavirus nucleocapsid protein (NP) of SARS-CoV-2 plays a central role in many functions important for virus proliferation including packaging and protecting genomic RNA. The protein shares sequence, structure, and architecture with nucleocapsid proteins from betacoronaviruses. The N-terminal domain (NP RBD ) binds RNA and the C-terminal domain is responsible for dimerization. After infection, NP is highly expressed and triggers robust host immune response. The anti-NP antibodies are not protective and not neutralizing but can effectively detect viral proliferation soon after infection. Two structures of SARS-CoV-2 NP RBD were determined providing a continuous model from residue 48 to 173, including RNA binding region and key epitopes. Five structures of NP RBD complexes with human mAbs were isolated using an antigen-bait sorting. Complexes revealed a distinct complement-determining regions and unique sets of epitope recognition. This may assist in the early detection of pathogens and designing peptide-based vaccines. Mutations that significantly increase viral load were mapped on developed, full length NP model, likely impacting interactions with host proteins and viral RNA.
59 BASIC BIOLOGICAL SCIENCES↗
Co-Extrusion of Dissimilar Aluminum Alloys via Shear-Assisted Processing and Extrusion
Bimetallic tubes are used when a component requires more than one performance requirement, for instance, strength/creep resistance and oxidation/corrosion resistance. Shear-assisted processing and extrusion (ShAPE) can be used to fabricate extrudates that are comparable or superior in performance relative to conventionally manufactured extrudates. For the first time, ShAPE has been successfully employed in producing bimetallic Al tubing consisting of 6061 and 7075 Al alloys. Both light and electron microscopy techniques were used to investigate the integrity of the tubes, especially the interface between the core and cladding of the bimetallic tubes. Void-free bimetallic tubes were produced using ShAPE. Quantification of tube integrity was carried out with tensile testing under as-extruded and post-aged conditions. All the bimetallic tubes in the as-extruded samples exhibited uniform elongation above 5% with good tensile strength. Key insights such as material flow during bimetallic tube extrusion were obtained from the characterization of remnant billet and simulation results from a smoothed particle hydrodynamics model.
36 MATERIALS SCIENCE↗
Feasibility Evaluation of a Solid Phase Scalable HEA Cladding Manufacturing Route
First of a kind development result on two low-energy solid-phase processes applied on an irradiation-resistant alloy, NiCoFeCrCu 0.12 , are achieved and demonstrate moderate feasibility of successful tube fabrication using shear assisted processing and extrusion (ShAPE™) and friction stir layer deposition as a bulk manufacturing process. The scope of the work is performed in four phases: 1) direct tube manufacturing of the irradiation-resistant high-entropy alloy (HEA) composite with increased strength, 2) co-shear lining manufacturing process for the increased strength and corrosion-resistant, irradiation-tolerant HEAs, 3) ShAPE of the radially gradient corrosion resistance alloy, and 4) alloy development and fabrication enabled through friction stir additive manufacturing processes among others. This report describes the development activities from April to December 2023 to manufacture a direct customizable thin-walled tubular product from irradiation-tolerant composite high-entropy alloys (C-HEAs) while the overall project is continuing in 2024.
36 MATERIALS SCIENCE↗
COUPLING SMOOTHED PARTICLE HYDRODYNAMICS WITH FINITE ELEMENT METHOD TO SIMULATE RESIDUAL STRESSES FROM FRICTION STIR PROCESSING
Friction stir processing (FSP) is a solid-state material processing technique that locally modifies the microstructure but also induces undesirable residual stresses. A robust numerical model for the FSP can help in mitigating these residual stresses. Heat source models within a finite element method (FEM) framework suffer from inaccuracies. In contrast, smoothed particle hydrodynamics (SPH) model that explicitly captures the material flow near the tool and the associated heat generation are accurate. However, the computational expense of SPH simulations can be prohibitive. In this work, we propose a coupled SPH-FEM framework. SPH is used to model the heat generation accurately near the tool and which is then inserted into to the FEM model as a heat source. To verify this proposed coupling approach, a test case is set up with typical FSP conditions and it is modeled in both SPH and SPH-FEM. The temperatures profiles were compared after the simulations have reached steady-state temperatures. The similarity of the temperature profiles from SPH-FEA and SPH validated the proposed coupling approach. This proposed approach achieves the accuracy of the SPH method while potentially retaining the low computational expense of FEM.
smoothed particle hydrodynamics, Finite Element Me↗
Diurnal variation of the fair-weather atmospheric electric field in Binchuan, China
With the purpose of understanding the variation of fair-weather atmospheric electric field, the vertical component of atmospheric electric field (recorded as Ez) has been measured in the town Binchuan (25°50'N, 100°34'E, 1438.7 m asl) of Dali city, Yunnan, China from June 14, 2017 to December 1, 2020. Automatic measured visual range is used as a proxy of aerosol concentration. The mean diurnal variation curve of the fair-weather Ez in Binchuan, having two peaks occurred at around 9LT and 20LT, shows little correlation with the well-known Carnegie Curve and other two high-latitude sites' Curves. While strong negative correlation between fair-weather Ez and visual range is found, indicating the variation of fair-weather is dominated by aerosol concentration. The main source of aerosol concentration variation probably sunrise and sunset effect. We support our findings by comparing Ez, visual range with sunrise and sunset times. The peaks (troughs) of Ez (visual range) are proved to have weak correlations with anthropogenic pollution through comparing the Ez, visual range under workdays and holidays.
54 ENVIRONMENTAL SCIENCES↗
RF operation of AlN/Al 0.25 Ga 0.75 N/AlN HEMTs with f T /f max of 67/166 GHz
Abstract We report on highly-scaled Al 0.25 Ga 0.75 N channel high electron mobility transistors. Regrown ohmic contacts covering the sidewall of the compressively strained Al 0.25 Ga 0.75 N channel exhibited a low contact resistance ofR c = 0.23 Ω · mm. Scaled devices with a T-shaped gate showed record high speed for any AlGaN-based transistors,f T /f max = 67/166 GHz, while simultaneously achieving high average breakdown field exceeding 2 MV cm −1 . The load-pull measurements performed at 10 GHz revealed a 20% peak power added efficiency with an output power density of 2 W mm −1 , which is mainly limited by the RF dispersion.
Physics↗
Hierarchical Control and Stability Analysis for a Nonisolated Grid-Tied DC Energy Router Integrating Energy Storage and Partial Distributed Generation
This article proposes a nonisolated dc converter-based energy router (dc-ER) and its operating strategy. Here, the intent is to integrate energy storage (ES), distributed generation (DG), local load, and dc power grid in an autonomous and more efficient way. The ES/DG power ports are coupled with each other in partial-type connections, which obtains higher voltage supply gain and direct input–output power transmission. High-voltage supply gain allows a wide solar power tracking range and the possibility of optimal battery charging/discharging. Direct input–output power transmission improves the energy conversion efficiency. In this article, the operating modes of dc-ER are first analyzed, followed by the optimal hardware design counting the DG current ripple minimization and the limitation caused by the power flow direction. Second, the mathematical model of dc-ER is deduced. The hierarchical control is then proposed to manage port energy in a flexible manner. The stability is analyzed by using impedance modeling. Finally, experimental and simulation results verify the superiorities of the proposed topology in terms of flexible operating mode transition and high-power conversion efficiency.
25 ENERGY STORAGE↗