Search NASA⌕ Search

Engineering topics

Li, S. S.

Publications and source records attributed to Li, S. S..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Barrier height enhancement of InP-based n-Ga(0.47)In(0.53)As Schottky-barrier diodes grown by molecular beam epitaxy

Barrier height enhancement of an InP-based p(+)n-Ga(0.47)In(0.53)As Schottky diode grown by MBE has been demonstrated for infra-red photodetector applications. A barrier height of 0.35 eV for n-Ga(0.47)In(0.53)As Schottky barrier diodes, was increased to the effective barrier height of 0.55 eV, with a p(+)-Ga(0.47)In(0.53)As surface layer of 30 nm thick. The results show a reverse leakage current density of 0.0015 A/sq cm and a junction capacitance of 0.3 pF, which are comparable to those of p-Ga(0.47)In(0.53)As Schottky-barrier diodes at a reverse bias voltage of 5 V.

Kim, J. H.↗
NASA NTRS1987

Calculations of the displacement damage and short-circuit current degradation in proton irradiated (AlGa)As-GaAs solar cells

A theoretical model for computing the displacement damage defect density and the short-circuit current (I sub sc) degradation in proton-irradiated (AlGa)As-GaAs p-n junction solar cells is presented. Assumptions were made with justification that the radiation induced displacement defects form an effective recombination center which controls the electron and hole lifetimes in the junction space charge region and in the n-GaAs active layer of the irradiated GaAs p-n junction cells. The degradation of I sub sc in the (AlGa)As layer was found to be negligible compared to the total degradation. In order to determine the I sub sc degradation, the displacement defect density, path length, range, reduced energy after penetrating a distance x, and the average number of displacements formed by one proton scattering event were first calculated. The I sub sc degradation was calculated by using the electron capture cross section in the p-diffused layer and the hole capture cross section in the n-base layer as well as the wavelength dependent absorption coefficients. Excellent agreement was found between the researchers calculated values and the measured I sub sc in the proton irradiated GaAs solar cells for proton energies of 100 KeV to 10 MeV and fluences from 10 to the 10th power p/square cm to 10 to the 12th power p/square cm.

Yeh, C. S.↗
NASA NTRS1985

Evaluation of AlsubxGasub1-xsubAs solar cells

Single junction GaAs solar cells have already attained an efficiency of 19% AMO which could potentially be increased to approx 20%, with some optimization. To achieve the higher efficiency the concept of multibandgap solar cells which utilizes a wider region of the solar spectrum should be sed. One of the materials for fabricating the top cell in a multibandgap solar cell is AlGaAs because it is compatible with GaAs in bandgap and lattice match. This is a very important consideration from the materials technology point of view, and the viability of this approach is evaluated.

Loo, R. Y.↗
NASA NTRS1984

Ohmic Versus Rectifying Contacts of Au to N-gaas by Ion Sputtering

Results of investigations of argon ion sputtering of heavily doped n-GaAs are compared with those obtained from studies of Au/low doping density n-GaAs contacts. The Au contact on Si-doped GaAs was nearly ohmic when the surface contamination (carbon and oxides) was reduced prior to deposition by chemical cleaning. However, when ion sputtering was used in situ to clean the surface, rectifying contact was produced whose barrier height varied with the energy of the sputtering ion. It was found that ion sputtering of GaAs doped to more than 3 x 10 to the 18th power/cu may be used to change ohmic contact to rectifying contacts. The barrier height may be changed by changing the ion energy. The behavior results from the sputter creation of deep level acceptor states at the GaAs surface. Annealing after sputtering can restore the contact to nearly an ohmic character.

Wang, Y. X.↗
NASA NTRS1984

Defect studies in one MeV electron irradiated GaAs and in Al/sub x Ga/sub l-x As P-N junction solar cells

Deep level transient spectroscopy reveals that the main electron traps for one-MeV electron irradiated GaAs cells are E9c)-0.31, E(c)-0.90 eV, and the main hole trap is due to the level. Electron trap density was found to vary from 3/tens-trillion ccm for 2/one quadrillion cm 3/3.7 quadrillion cm for 21 sextillion cm electron fluence for electron fluence; a similar result was also obtained for the hole trap density. As for the grown-in defects in the Al(x)Ga(1-x)As p-n junciton cells, only two electron traps with energies of E(c)-0.20 and E(c)-0.34 eV were observed in samples with x = 0.17, and none was found for x 0.05. Auger analysis on the Al(x)Ga(1-x) As window layer of the GaAs solar cell showed a large amount of oxygen and carbon contaminants near the surface of the AlGaAs epilayer. Thermal annealing experiment performed at 250 C for up to 100 min. showed a reduction in the density of both electron traps.

Li, S. S.↗
NASA NTRS1982

Defects and annealing studies in 1-Me electron irradiated (AlGa)As-GaAs solar cells

The deep-level defects and recombination mechanisms in the one-MeV electron irradiated (AlGa)As-GaAs solar cells under various irradiation and annealing conditions are discussed. Deep-level transient spectroscopy (DLTS) and capacitance-voltage (CV) techniques were used to determine the defect and recombination parameters such as energy levels and defect density, carrier capture cross sections and lifetimes for both electron and hole traps as well as hole diffusion lengths in these electron irradiated GaAs solar cells. GaAs solar cells used in this study were prepared by the infinite solution melt liquid phase epitaxial (LPE) technique at Hughes Research Lab., with (Al0.9Ga0.1)-As window layer, Be-diffused p-GaAs layer on Sn-doped n-GaAs or undoped n-GaAs active layer grown on n(+)-GaAs substrate. Mesa structure with area of 5.86x1000 sq cm was fabricated. Three different irradiation and annealing experiments were performed on these solar cells.

Li, S. S.↗
NASA NTRS1982

Grown-in defects and defects produced by 1-Me electron irradiated in Al0.3Ga0.7As P-N junction solar cells

Studies of grown-in defects and defects produced by the one-MeV electron irradiation in Al sub 0.3 Ga sub 0.7As p-n junction solar cells fabricated by liquid phase epitaxial (LPE) technique were made for the unirradiated and one-MeV electron irradiated samples, using DLTS and C-V methods. Defect and recombination parameters such as energy level, defect density, carrier capture cross sections and lifetimes were determined for various growth, annealing, and irradiation conditions.

Li, S. S.↗
NASA NTRS1981

Effects of low temperature periodic annealing on the deep-level defects in 200 keV proton irradiated AlGaAs-GaAs solar cells

The GaAs solar cell has shown good potential for space applications. However, degradation in performance occurred when the cells were irradiated by high energy electrons and protons in the space environment. The considered investigation is concerned with the effect of periodic thermal annealing on the deep-level defects induced by the 200 keV protons in the AlGaAs-GaAs solar cells. Protons at a fluence of 10 to the 11th P/sq cm were used in the irradiation cycle, while annealing temperatures of 200 C (for 24 hours), 300 C (six hours), and 400 C (six hours) were employed. The most likely candidate for the E(c) -0.71 eV electron trap observed in the 200 keV proton irradiated samples may be due to GaAs antisite, while the observed E(v) +0.18 eV hole trap has been attributed to the gallium vacancy related defect. The obtained results show that periodic annealing in the considered case does not offer any advantages over the one time annealing process.

Li, S. S.↗
NASA NTRS1981

Electronic properties of deep-level defects in proton irradiated AlGaAs-GaAs solar cells

Deep level transient spectroscopy and capacitance voltage techniques as well as analysis of the forward current voltage (I-V) characteristics and SEM-EIC data were carried out for proton irradiated GaAs solar cells over a wide range of proton energies and proton fluences. Defect and recombination parameters such as defect energy levels and density, carrier capture cross sections and lifetimes as well as diffusion lengths in the undoped n-GaAs LPE layers were determined. Good correlation between these defect parameters and solar cell performance parameters was obtained for GaAs solar cells irradiated by 200 and 290 KeV protons. It was found that 200 to 290 KeV protons will produce the most defects and damages to the GaAs solar cell structure used. The influence of the low temperature (200 to 400 C) periodic thermal annealing on the deep level defects and the performance of the 200 KeV proton irradiated cells is discussed.

Li, S. S.↗
NASA NTRS1981

Study of radiation induced deep-level defects and annealing effects in the proton irradiated AlGaAs-GaAs solar cells

The radiation induced deep-level defects and the recombination parameters in the proton irradiated AlGaAs-GaAs p-n junction solar cells were investigated over a wide range of proton energies (from 50 KeV to 10 MeV) and proton fluences (from 10 to the 10th to 10 to the 13th P/sq cm), using DLTS, I-V, C-V, and SEM-EMIC measurement techniques. The measurements were used to determine the defect and recombination parameters such as defect density and energy level, carrier lifetimes, and the hole diffusion lengths in the GaAs LPE layers. Results show that a good correlation was obtained between the measured defect parameters and the dark recombination current as well as the performance parameters of the solar cells. The most damages to the cell were produced by the 200 KeV protons. In addition, the effects of low temperatures (200 to 400 C) thermal annealing on the deep-level defects and the dark current of the 200 KeV proton irradiated samples were examined.

Li, S. S.↗
NASA NTRS1980

Effects of thermal annealing on the deep-level defects and I-V characteristics of 200 keV proton irradiated AlGaAs-GaAs solar cells

Detailed characterization of deep-level defects and analysis of dark I-V data in 200 keV proton irradiated AlGaAs-GaAs solar cells have been carried out for several proton fluences (5 x 10 to the 11th, 10 to the 12th, and 10 to the 13th P/sq cm), using DLTS, C-V, and I-V measurement techniques. To study the effect of low temperature thermal annealing on the deep-level defect properties, these irradiated samples were annealed in vacuum at 300 C for one hour. Comparison was then made on the measured defect parameters (i.e., defect energy levels and densities) and the dark I-V characteristics for both the annealed and unannealed samples.

Li, S. S.↗
NASA NTRS1980

Study of radiation induced deep-level defects in proton irradiated AlGaAs-GaAs solar cells

Radiation induced deep-level defects (both electron and hole traps) in proton irradiated AlGaAs-GaAs p-n junction solar cells are investigated along with the correlation between the measured defect parameters and the solar cell performance parameters. The range of proton energies studied was from 50 KeV to 10 MeV and the proton fluence was varied from 10 to the 10th power to 10 to the 13th power P/sq cm. Experimental tools employed include deep-level transient spectroscopy, capacitance-voltage, current voltage, and SEM-EBIC methods. Defect and recombination parameters such as defect density and energy level, capture cross section, carrier lifetimes and effective hole diffusion lengths in n-GaAs LPE layers were determined from these measurements.

Li, S. S.↗
NASA NTRS1980

Deep-level defects and recombination parameters in proton irradiated AlGaAs-GaAs solar cells

The deep-level defects produced in high efficiency AlGaAs-GaAs solar cells by proton energies of 50, 100, 200, and 290 keV are investigated. Proton fluences were from 10 to the 10th to 10 to the 13th p/sq cm. The results show that the diode ideality factor varies between 1.9 and 2.1, indicating that the dominant current component is due to the recombination of electron-hole pairs via deep-level traps in the junction space charge region of these diodes. The recombination current increases with increasing proton fluence and proton energy. The reduction of open circuit voltage, short circuit current, and conversion efficiency in the irradiated cells relates directly to the density of the deep-level defects induced by proton irradiation.

Li, S. S.↗
NASA NTRS1978

Study of electronic properties in proton- and electron-irradiated GaAlAs and GaAs solar cell materials

Diagnostical measurement techniques such as dark I-V, C-V, the thermally insulated capacitance, and the deep level transient spectroscopy methods were employed to study defect properties in the proton-irradiated n-GaAs materials. Defect energy levels, thermal emission rates, and capture cross sections of electrons as well as trap densities were deduced from these measurements and the results are presented. Correlations between the measured defect parameters and the dark I-V characteristics of the n-GaAs Schottky barrier diodes are also discussed. Defect energy levels (i.e., electron traps) determined are also compared with published data in order to identify their physical origins.

Li, S. S.↗
NASA NTRS1975

Process-induced defects in terrestrial solar cells

Experimental and theoretical work on low resistivity, high efficiency solar cells indicates the dominant role that defects take in determining performance. High doping mechanisms produce gap shrinkage by band tailing, impurity band widening and impurity misfit; altered interband transmission rates result from Auger impact, SRH processes, or from electronic tunneling via defects. Characterizations of cell materials for their defects and their relations to the chosen fabrication processes are proposed.

Lindholm, F. A.↗
NASA NTRS1975

Fundamental limitations imposed by high doping on the performance of pn junction silicon solar cells

Fundamental limitations imposed on the performance of silicon junction solar cells by physical mechanisms accompanying high doping are described. The one-dimensional mechanisms divide into two broad categories: those associated with band-gap shrinkage and those associated with interband transition rates. By extending the traditional method of analysis and comparing with measurement, it is shown that the latter kind of mechanism dominates in determining the open-circuit voltage in a one-dimensional model of a 0.1 ohm-cm cell at 300 K. As an alternative dominant mechanism, a three-dimensional model involving thermodynamically stable clusters of impurities in the highly-doped diffused layer is suggested.

Lindholm, F. A.↗