Engineering topics

Li, Tai-De

Publications and source records attributed to Li, Tai-De.

8 records

DOE OSTI2024

Template-Assisted Growth of High-Quality α-Phase FAPbI 3 Crystals in Perovskite Solar Cells Using Thiol-Functionalized MoS 2 Nanosheets

Formamidinium lead iodide (FAPI) has gained attention for hybrid perovskite solar cell (PSC) applications due to its enhanced stability and narrow bandgap. However, a significant challenge remains in inducing and stabilizing the elusive perovskite “black phase”—photoactive cubic α-FAPI—as the relatively bulky FA + cations tend to favor the thermodynamically stable nonphotoactive “yellow phase”. Here, in this study, we present a templated growth strategy employing thiol-functionalized MoS 2 nanosheets as templates. By introduction of 3-mercaptopropionic acid (MPA)-functionalized MoS 2 as a growth template, precise control over crystal formation was achieved, favoring the growth of high-quality α-FAPI films. These advanced templated films exhibited substantial improvements in charge transport properties, efficient light absorption, and enhanced charge extraction. As a result, the PSCs achieved a significantly enhanced power conversion efficiency (PCE) compared to the nontemplated control device, increasing from 20.6 to 22.5%. The MoS 2 -incorporated device also demonstrated excellent shelf stability, maintaining 91% of the initial PCE even after 1600 h of storage without device encapsulation.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Interplay between Local Moment and Itinerant Magnetism in the Layered Metallic Antiferromagnet TaFe 1.14 Te 3

Two-dimensional antiferromagnets have garnered considerable interest for the next generation of functional spintronics. However, many bulk materials from which two-dimensional antiferromagnets are isolated are limited by their air sensitivity, low ordering temperatures, and insulating transport properties. TaFe 1+y Te 3 aims to address these challenges with increased air stability, metallic transport, and robust antiferromagnetism. Here, we synthesize TaFe 1+y Te 3 (y = 0.14), identify its structural, magnetic, and electronic properties, and elucidate the relationships between them. Axial-dependent high-field magnetization measurements on TaFe 1.14 Te 3 reveal saturation magnetic fields ranging between 27-30 T with saturation magnetic moments of 2.05- 2.12 μ B . Magnetotransport measurements confirm TaFe 1.14 Te 3 is metallic with strong coupling between magnetic order and electronic transport. Angle-resolved photoemission spectroscopy measurements across the magnetic transition uncover a complex interplay between itinerant electrons and local magnetic moments that drives the magnetic transition. In conclusion, we demonstrate the ability to isolate few-layer sheets of TaFe 1.14 Te 3 , establishing TaFe 1.14 Te 3 as a potential platform for two-dimensional spintronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2023

Determination of the Interfacial Energy between Graphene Nanoplatelets and Deuterated or Hydrogenated Polystyrene

The tracer diffusion coefficients of various graphene nanoplatelet-polystyrene (GNP-PS) systems were determined by using dynamic secondary ion mass spectrometry, which provided insights into the interactions within the polymer nanocomposite system. Bilayer films, where one contained trace amounts of deuterated polystyrene (dPS), were produced, and the interdiffusion was measured by detecting the position of the dPS interface. GNPs were placed in both or only one of the two layers. The diffusion coefficient was decreased when GNPs were present in both layers as compared to the samples without GNP, indicating an attractive interaction between GNP and polystyrene. Surprisingly, the coefficient increased relative to the control when GNPs were present only in the PS containing layer, whereas it decreased most strongly when GNP and dPS were present only in the same layer, indicating that an additional preference existed for GNPs and dPS. A significant difference in interfacial energies was measured using contact angle goniometry of PS or dPS droplets on flat GNP layers, confirming the preferential interaction. DFT calculations were used to calculate the interfacial interaction between GNP and dPS or PS, and they showed an attractive potential which was maximal when the PS rings were conformal with the GNP structure. Furthermore, the differential energy between PS and dPS at the GNP interface was in excellent agreement with the measured value. In contrast, contact angle goniometry indicated that the interaction between GNP and poly(methyl methacrylate) (PMMA) was unfavorable, and no difference in interfacial energy between dPMMA and PMMA was observed. Therefore, these techniques can provide a means for determining the relative affinity between GNP and different polymer hosts, which can be an important consideration in the mechanics and adhesion properties of the compounds.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Application of the core shell model for strengthening polymer filament interfaces

While surface segregation has been intensively studied in thin films, relatively little has been investigated in filament geometries. In contrast to thin films, the filament surface forms a continuum, with interactions both at the free air and internal filament interface, which makes it difficult to achieve an equilibrium configuration. This asymmetry has become particularly apparent with the increasing use of additive manufacturing where entire structures are constructed via layered deposition of filamentous layers from a moving thermal nozzle. In addition, this process is highly non-equilibrated with poor thermal retention and is responsible for insufficient filament–filament interfacial fusion and internal pore formation along the printing direction. These features all contribute to poor mechanical and structural properties, which are exacerbated in semi-crystalline polymers, such as Polylactic Acid (PLA), where the melting point, T m , is much higher than the glass transition, T g . Even though system is liquid the molecules become ordered within the crystal structure and this ordering interferes with interdiffusion, which in turn prevents proper interfacial fusion. Capitalizing on the differential in surface tension, we show that addition of less than 1%, or trace amounts, of longer chain polymers, an oriented core shell structure, will be formed with a self-limiting thickness of three time the radius of gyration, R g , of the tracer chains. The lower T g of the tracers and their orientation makes them poised for interdiffusion when subsequent layers are deposited producing structures with significant improvement of the mechanical properties and internal structural integrity.

36 MATERIALS SCIENCE↗

DOE OSTI2022

The molecular mechanism of load adaptation by branched actin networks

Branched actin networks are self-assembling molecular motors that move biological membranes and drive many important cellular processes, including phagocytosis, endocytosis, and pseudopod protrusion. When confronted with opposing forces, the growth rate of these networks slows and their density increases, but the stoichiometry of key components does not change. The molecular mechanisms governing this force response are not well understood, so we used single-molecule imaging and AFM cantilever deflection to measure how applied forces affect each step in branched actin network assembly. Although load forces are observed to increase the density of growing filaments, we find that they actually decrease the rate of filament nucleation due to inhibitory interactions between actin filament ends and nucleation promoting factors. The force-induced increase in network density turns out to result from an exponential drop in the rate constant that governs filament capping. The force dependence of filament capping matches that of filament elongation and can be explained by expanding Brownian Ratchet theory to cover both processes. We tested a key prediction of this expanded theory by measuring the force-dependent activity of engineered capping protein variants and found that increasing the size of the capping protein increases its sensitivity to applied forces. In summary, we find that Brownian Ratchets underlie not only the ability of growing actin filaments to generate force but also the ability of branched actin networks to adapt their architecture to changing loads.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2021

Improving Thermal Stability of Perovskite Solar Cells by Suppressing Ion Migration Using Copolymer Grain Encapsulation

Thermal stability of organic–inorganic hybrid perovskites (OIHPs) remains as one of the critical challenges against the stable operation of perovskite solar cells (PSCs) in direct sunlight with elevated temperatures. Here, we show that the addition of a polystyrene-co-polyacrylonitrile (SAN) copolymer can significantly enhance thermal stability of OIHPs and improve the stability of the corresponding PSCs by suppressing the migration of organic cations in OHIP. The methylammonium lead iodide (MAPI) with SAN incorporated within the perovskite layer featured a superior thermal stability compared to pure MAPI without SAN, only displaying an average of 5–15% decrease in PCE even after continuous thermal aging for 24 h at 100 °C. The secondary ion mass spectrometry revealed that the thermal degradation of the pure MAPI was largely associated with MA+ out-migration. Conducting atomic force microscopy analysis further indicated that the incorporated SAN led to a suppression of ionic currents present at the grain boundaries of the perovskite film, which was understood by high immiscibility between SAN and MA+ components as confirmed by the experimentally estimated Flory–Huggins parameter between them. This study newly identifies a potential of using polymer grain encapsulation for enhancing thermal stability of OIHPs and their solar cell performance by suppressing the out-diffusion of cationic organic components.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Spatial defects nanoengineering for bipolar conductivity in MoS 2

Understanding the atomistic origin of defects in two-dimensional transition metal dichalcogenides, their impact on the electronic properties, and how to control them is critical for future electronics and optoelectronics. Here, we demonstrate the integration of thermochemical scanning probe lithography (tc-SPL) with a flow-through reactive gas cell to achieve nanoscale control of defects in monolayer MoS 2 . The tc-SPL produced defects can present either p- or n-type doping on demand, depending on the used gasses, allowing the realization of field effect transistors, and p-n junctions with precise sub-μm spatial control, and a rectification ratio of over 10 4 . Doping and defects formation are elucidated by means of X-Ray photoelectron spectroscopy, scanning transmission electron microscopy, and density functional theory. We find that p-type doping in HCl/H 2 O atmosphere is related to the rearrangement of sulfur atoms, and the formation of protruding covalent S-S bonds on the surface. Alternatively, local heating MoS 2 in N 2 produces n-character.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Enhancing Chemical Stability and Suppressing Ion Migration in CH 3 NH 3 PbI 3 Perovskite Solar Cells via Direct Backbone Attachment of Polyesters on Grain Boundaries

Organic–inorganic halide perovskites feature excellent optoelectronic properties but poor chemical stability. While passivating perovskite grain boundary (GB) by polymers shows prospects on long-term performance of perovskite solar cells (PSCs), its detailed impact on the ion migration phenomenon, which largely deteriorates the PSC stability, remains less probed. In this work, we introduce a new polar polymer, polycaprolactone (PCL), to passivate GBs of methylammonium lead triiodide (MAPbI 3 ) perovskite with only 1–2 polymer monolayers via direct backbone attachment. The PSCs with passivated MAPbI 3 , using a classic but less stable Spiro-OMeTAD (2,2',7,7'-tetrakis[N,N-di(4-methoxyphenyl)amino]-9,9'-spirobifluorene) hole transport layer (HTL), exhibit improved power conversion efficiencies up to 20.1%, with 90% of the initial PCE being preserved after 400 h ambient storage, and 80% even after 100 h, 85 °C aging. The improved PSC stability indicates critical roles of PCL GB passivation in retarding moisture-induced decomposition and suppressing ion migration within the perovskite. Furthermore, time-of-flight secondary ion mass spectrometry reveals that I– ions can actively migrate into the electrode, HTL, and their interface in nonpassivated PSCs, even without an externally applied electric field, while such migration is significantly mitigated in PCL-passivated PSCs. This effective GB passivation by PCL suggests an important potential of polymer additives toward the development of stable high-performance PSCs.

36 MATERIALS SCIENCE↗