Search NASA⌕ Search

Engineering topics

Li, Tianyi

Publications and source records attributed to Li, Tianyi.

69 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Insights into Ti doping for stabilizing the Na 2/3 Fe 1/3 Mn 2/3 O 2 cathode in sodium ion battery

Iron- and manganese-based layered metal oxides, as cathodes for sodium ion batteries, have received widespread attention because of the low cost and high specific capacity. However, the Jahn-teller effect of Mn 3+ ions and the resulted unstable structure usually lead to continuously capacity decay. Herein, Titanium (Ti) has been successfully doped into Na 2/3 Fe 1/3 Mn 2/3 O 2 to suppress the Jahn-Teller distortion and improve both cycling and rate performance of sodium ion batteries. In situ high-energy synchrotron X-ray diffraction study shows that Ti-doped compound (Na 2/3 Fe 1/3 Mn 0.57 Ti 0.1 O 2 ) can maintain the single P2 phase without any phase transition during the whole charging/discharging process. Further, various electrochemical characterizations are also applied to explore the better kinetics of sodium ions transfer in the Na 2/3 Fe 1/3 Mn 0.57 Ti 0.1 O 2 . This work provides a comprehensive insight into the Ti-doping effects on the performance from both structural and electrokinetic perspectives.

25 ENERGY STORAGE↗
DOE OSTI2022

Effect of Cationic (Na + ) and Anionic (F – ) Co-Doping on the Structural and Electrochemical Properties of LiNi 1/3 Mn 1/3 Co 1/3 O 2 Cathode Material for Lithium-Ion Batteries

Elemental doping for substituting lithium or oxygen sites has become a simple and effective technique to improve the electrochemical performance of layered cathode materials. Compared with single-element doping, this work presents an unprecedented contribution to the study of the effect of Na + /F – co-doping on the structure and electrochemical performance of LiNi 1/3 Mn 1/3 Co 1/3 O 2 . The co-doped Li 1-z Na z Ni 1/3 Mn 1/3 Co 1/3 O 2-z F z (z = 0.025) and pristine LiNi 1/3 Co 1/3 Mn 1/3 O 2 materials were synthesized via the sol–gel method using EDTA as a chelating agent. Structural analyses, carried out by X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy, revealed that the Na + and F – dopants were successfully incorporated into the Li and O sites, respectively. The co-doping resulted in larger Li-slab spacing, a lower degree of cation mixing, and the stabilization of the surface structure, which substantially enhanced the cycling stability and rate capability of the cathode material. The Na/F co-doped LiNi 1/3 Mn 1/3 Co 1/3 O 2 electrode delivered an initial specific capacity of 142 mAh g –1 at a 1C rate (178 mAh g –1 at 0.1C), and it maintained 50% of its initial capacity after 1000 charge–discharge cycles at a 1C rate.

25 ENERGY STORAGE↗
DOE OSTI2022

Visualizing the Nanoscale Oxygen and Cation Transport Mechanisms during the Early Stages of Oxidation of Fe–Cr–Ni Alloy Using In Situ Atom Probe Tomography

Abstract Understanding the early stages of interactions between oxygen and material surfaces—especially at very high spatial resolutions—is highly beneficial for fields ranging from materials degradation, corrosion, geological sciences, forensics, and catalysis. The ability of in situ atom probe tomography (APT) is demonstrated to track the diffusion of oxygen and metal ions at nanoscale spatial resolution during the early stages of oxidation of a model Fe–Cr–Ni alloy. Using 18 O isotope tracers in these in situ APT experiments and complementary ex situ multimodal microscopy, spectroscopy, and computational simulations allows to precisely analyze the kinetics of oxidation and determine that outward cation diffusion to oxide/air interface is the primary mechanism for intragranular oxide growth in this alloy at 300 °C. This unique in situ isotopic tracer APT approach and the insights gained can be highly beneficial for studying early stages of gas–surface reactions in a broad array of materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synchrotron X‐Ray‐Driven Nitrogen Reduction on an AgCu Thin Film

Abstract Nitrogen (N 2 ) is an essential element for life, but kinetically stable N 2 in the atmosphere needs to be reduced to biologically available forms as a nutrient for organisms. Abiotic nitrogen fixation is critical to the origin of life on the early Earth, which is due to lightning or mineral‐based reduction. Here, synchrotron X‐ray‐induced silver nitrate formation on a silver copper (AgCu) thin‐film is reported. Time‐resolved X‐ray diffraction measurements show that under intense X‐ray exposure, initially formed silver oxides (AgOx) are quickly converted to silver nitrate (AgNO 3 ). Interestingly, AgNO 3 is first formed in its high‐temperature phase with a space group of R3cH , which gradually transforms to the room temperature phase with a space group of Pbca under continuous X‐ray irradiation. The result not only provides a new clue about the abiotic nitrogen reduction prior to life but also demonstrates a novel strategy of materials synthesis using synchrotron X‐rays.

Hui, Jian↗
DOE OSTI2022

Diffraction and thermal effect of a Bessel-Gaussian laser for Ag nanoparticle deposition

Nanoparticles are known to sinter at much lower temperatures than the corresponding bulk or micro size particles. A laser-assisted sintering process is considered in this study to sinter Ag nanoparticles by dispensing Ag paste onto an indium tin oxide-coated Si substrate. The Gaussian beam of a CO 2 laser source is propagated through axicon and biconvex lenses, and the resulting hollow beam is focused on the Ag paste with a hollow parabolic mirror. A Bessel-Gaussian irradiance distribution is obtained at the focal plane of the parabolic mirror due to the interference of the hollow laser cone. The Fresnel diffraction approximation is considered to determine the phasor of the laser and an analytical approach is implemented to calculate the irradiance distribution of the Bessel-Gaussian beam. This irradiance distribution is utilized as a heat source in a heat conduction model and the temperature distribution is analyzed for thin Ag films formed during the laser sintering of Ag nanoparticles. An analytical expression is obtained for the temperature distribution by solving the heat conduction equation using Fourier transform for finite media. The widths of the deposited Ag lines are predicted from the temperature profiles and the model predictions compare well with the experimental results. The isotherms are found to be geometrically noncongruent with convex and concave tips depending on the locally maximum and minimum irradiances of the Bessel-Gaussian beam, respectively. The convex and concave tips, however, appear in the same isotherm for sufficiently high substrate speed relative to the laser beam.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Synchrotron X-ray-induced Synthesis of Copper Hydroxide Nitrate Nanoplates on Cu Thin Films in an Ambient Atmosphere

Synchrotron X-rays are widely used for material characterizations. However, they can also ionize atoms and molecules to damage and manipulate probed materials. We report here an X-ray-induced growth of copper hydroxide nitrate, Cu 2 (OH) 3 NO 3 , on copper thin films in the ambient atmosphere without solvents and thermal treatment. In situ synchrotron X-ray diffraction measurements showed that the time-dependent growth process of the Cu 2 (OH) 3 NO 3 is accompanied by the consumption of Cu metal and can be described by a sigmoidal model. The growth rate was reduced after the initial fast growth period. Scanning electron microscopy (SEM) images show that the isolated islands of Cu 2 (OH) 3 NO 3 nanoplates formed in the beginning, which grew together with new nanoplates formed under continued X-ray irradiation. The result demonstrated that high-flux synchrotron X-rays may provide an unconventional approach to synthesizing and manipulating materials, which will inspire future investigation both experimentally and theoretically.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Pushing Lithium–Sulfur Batteries towards Practical Working Conditions through a Cathode–Electrolyte Synergy

Abstract The commercialization of lithium–sulfur (Li−S) batteries is still hindered by the unsatisfactory cell performance under practical working conditions, which is mainly caused by the sluggish cathode redox kinetics, severe polysulfide shuttling, and poor Li stripping/plating reversibility. Herein, we report an effective strategy by combining Se‐doped S hosted in an ordered macroporous framework with a highly fluorinated ether (HFE)‐based electrolyte to simultaneously address the aforementioned issues in both cathode and anode. A reversible and stable high areal capacity of >5.4 mAh cm −2 with high Coulombic efficiency >99.2 % can be achieved under high areal Se/S loading (5.8 mg cm −2 ), while the underlying mechanism was further revealed through synchrotron X‐ray probes and Time‐of‐Flight Secondary Ion Mass Spectrometry (ToF‐SIMS). The practical application potential was further evaluated at low (0 °C) and high (55 °C) temperatures under high areal Se/S loading (>5.0 mg cm −2 ) and thin Li metal (40 μm).

Zhao, Chen↗
DOE OSTI2022

Pushing Lithium–Sulfur Batteries towards Practical Working Conditions through a Cathode–Electrolyte Synergy

The commercialization of lithium-sulfur (Li-S) batteries is still hindered by the unsatisfactory cell performance under practical working conditions, which is mainly caused by the sluggish cathode redox kinetics, severe polysulfide shuttling, and poor Li striping/platting reversibility. We reported an effective strategy by combining Se-doped S hosted in an ordered macroporous framework with highly fluorinated ether (HFE)-based electrolyte to simultaneously address the aforementioned issues in both cathode and anode. A reversible and stable high areal capacity of > 5.4 mAh cm -2 with high coulombic efficiency > 99.2% can be achieved under high areal Se/S loading (5.8 mg cm -2 ), while the underlying mechanism was further revealed through synchrotron X-ray probes and Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The practical application potential was further evaluated at low (0 °C) and high (55 °C) temperatures under high areal Se/S loading (> 5.0 mg cm -2 ) and thin Li metal (40 µm).

25 ENERGY STORAGE↗
DOE OSTI2022

Targeted masking enables stable cycling of LiNi 0.6 Co 0.2 Mn 0.2 O 2 at 4.6V

Layered LiNi x Co y Mn 1–x-y O 2 (NCM, or NCMxy(1-x-y)) is a dominant family of cathode materials for lithium-ion batteries (LIBs) due to its high energy density. Among all NCM cathode materials, NCM622 possess the optimal energy density at high potential (≥ 4.6 V vs. Li/Li + ). However, the practical application of NCM622 at high voltage (≥ 4.6 V) is limited by its parasitic reactions and associated safety concerns. Completely physical isolation has been considered as the main approach to mitigate the parasitic reaction. It has also been previously demonstrated that the interface reaction has active site selectivity, and that the reactivity of the active sites can effectively suppressed by blocking the chemically active sites. Herein, a targeted masking by LiFePO 4 @C nanoplates is reported to unlock the stable performance of NCM622 up to 4.6 V vs. Li/Li + . The (targeted masked-NCM622)|graphite pouch cell shows 86.5% capacity retention after 1000 cycles and its maximum temperature during thermal runaway is dramatically reduced from 570 °C to 415 °C. Systematic in/ex situ characterizations, first-principles calculations and half/pouch targeted LiFePO 4 @C covers the surface of NCM partcell evaluation prove that PO 4 3- is preferentially adsorbed on transition metal sites, stabilizing both the transition metal ions and oxygen ions on the surface against the ethylene carbonate-containing traditional electrolyte even under high voltage (≥ 4.6 V vs. Li/Li + ). Furthermore, this work opens up new venue for rational design of high-performance cathode materials through a low-cost and scalable decoration process, and reveal a new understanding of interfacial activity of materials.

25 ENERGY STORAGE↗
DOE OSTI2022

Thermal dynamics of P2-Na 0.67 Ni 0.33 Mn 0.67 O 2 cathode materials for sodium ion batteries studied by in situ analysis

Cobalt-free layered Na 0.67 Ni 0.33 Mn 0.67 O 2 is an attractive cathode material for sodium ion batteries. The thermal stability of cathode materials is crucial to their practical applications. In the current work, we investigate structural and morphological evolution in P2-type Na 0.67 Ni 0.33 Mn 0.67 O 2 cathode materials during annealing via in situ synchrotron X-ray diffraction and transmission electron microscopy. Insights are obtained from the two complementary in situ characterizations (at different length scales) in term of the thermal stability of P2-Na 0.67 Ni 0.33 Mn 0.67 O 2 cathode materials. Here, the results indicate that the hexagonal P2 phase remains unchanged during the heat treatment process, and thermally driven expansion/contraction of lattice parameters exhibit an anisotropic character in the a and c directions. In addition, interfaces/grain boundaries play an important role in the structural stability, which leads to the distinct morphological evolution between the polycrystalline and single-crystal particles.

25 ENERGY STORAGE↗
DOE OSTI2020

In-Situ Characterization of Dynamic Morphological and Phase Changes of Selenium-doped Germanium Using a Single Particle Cell and Synchrotron Transmission X-ray Microscopy

The dynamic information of lithium-ion battery active materials obtained from coin cell-based in-situ characterizations might not represent the properties of the active material itself because many other factors in the cell could have impacts on the cell performance. To address this problem, a single particle cell was developed to perform the in-situ characterization without the interference of inactive materials in the battery electrode as well as the X-ray-induced damage. In this study, the dynamic morphological and phase changes of selenium-doped germanium (Ge 0.9 Se 0.1 ) at the single particle level were investigated via synchrotron-based in-situ transmission X-ray microscopy. The results demonstrate the good reversibility of Ge 0.9 Se 0.1 at high cycling rate that helps understand its good cycling performance and rate capability. This in-situ and operando technique based on a single particle battery cell provides an approach to understanding the dynamic electrochemical processes of battery materials during charging and discharging at the particle level.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Blade-Type Reaction Front in Micrometer-Sized Germanium Particles during Lithiation

To investigate the lithium transport mechanism in micrometer-sized germanium (Ge) particles, in situ focused ion beam-scanning electron microscopy was used to monitor the structural evolution of individual Ge particles during lithiation. Our results show that there are two types of reaction fronts during lithiation, representing the differences of reactions on the surface and in bulk. Further, the cross-sectional SEM images and transmission electron microscopy characterizations show that the interface between amorphous Li x Ge and Ge has a wedge shape because of the higher Li transport rate on the surface of the particle. The blade-type reaction front is formed at the interface of the amorphous Li x Ge and crystalline Ge and is attributed to the large strain at the interface.

25 ENERGY STORAGE↗
DOE OSTI2020

A self-healing liquid metal anode with PEO-Based polymer electrolytes for rechargeable lithium batteries

In this study, a Ga-Sn liquid metal alloy material is demonstrated as a self-healing anode system due to its fluidity via operando synchrotron-based transmission X-ray microscopy and X-ray diffraction experiments. Cracks formed due to volume expansions can be recovered by the fluidity of the liquid metals. By incorporating with a poly(ethylene oxide) (PEO)-based electrolyte at 60°C, the Ga-Sn anode shows a reversible lithium insertion and extraction process with a high initial discharge specific capacity of 682 mAh g -1 , followed by delivering a capacity of 462 mAh g -1 in the second cycle at C/20 rate. Furthermore, compared with its solid counterparts, the Ga-Sn liquid metal anode demonstrates a better capability to maintain its mechanical integrity and better contact with PEO solid electrolytes due to its advantageous features of the liquid. This study suggests a potential strategy to use liquid metal alloys with polymer solid electrolyte to solve the anode challenges in rechargeable lithium batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In Situ and Operando Morphology Study of Germanium-Selenium Alloy Anode for Li-ion Batteries

Selenium-doped germanium (GeSe) micrometersized particles have been reported with good cycling performance and rate capability due to a Li-Se-Ge network formed during the first lithiation that provides a Li-ion fast pathway. To understand the effect of the Li-Se-Ge network at a high cycling rate, we monitored the morphology change of both pure Ge and GeSe particles during cycling with an in situ/operando focused-ion beam-scanning electron microscope method. Our results showed that the proposed inactive Li-Se-Ge network can provide fast Li-ion transport and also buffer volume variation, resulting in homogeneous volume change and uniform microstructural evolution.

germanium↗