Search NASA⌕ Search

Engineering topics

Li, Xiaodong

Publications and source records attributed to Li, Xiaodong.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Low-Cost, High-Performance Carbon Fiber for Compressed Natural Gas Storage Tanks (Final Technical Report – Down Select Report)

The aim of this project is to reduce the cost of Type IV, carbon fiber (CF) composite overwrap compressed gas storage tanks by reducing the cost of CF and CF composites. The project team worked to reduce the cost of CF by exploring and testing opportunities for a low-cost alternative precursor material for CF production to supplant market-dominant and costly polyacrylonitrile (PAN). Concurrently, the team aimed to reduce the cost of the tanks at the composite level by improving the interfacial adhesion between the fibers and the matrix resin through the incorporation of low-cost nanoparticles recycled from waste materials, which would reduce the volume of costly CF required to achieve the same tank performance. At the end of the first year, the project team selected mesophase pitch as the primary precursor candidate from a field of materials based on the superior mechanical performance and cost-saving potential. During the second year, the team produced CFs derived from mesophase pitch achieving an average tensile strength of 365.6 ksi and average tensile modulus of 40.74 Msi. Facility availability for spinning and converting these fibers at greater scale has hindered scale-up demonstration, but the team has identified opportunities to conduct this work in the near term. Cost modeling shows that these mesophase pitch-derived CFs can be up to 40% less expensive than PAN-derived CFs due to the lower cost of the feedstock material, higher throughput, greater conversion yield, and lower cost spinning method and compared to PAN. Additionally, the team has demonstrated at lab-scale that nanoparticle coating CFs can significantly increase the interfacial shear strength and load transfer efficiency of CFs in a matrix. Single filament pull-out testing showed a 27% average increase in max interfacial shear strength due to this coating. A continuous method of applying these coatings to a tow of CF has been developed for scale-up. 26 m tows of coated CFs were produced using this system and formed into composite ring samples for ASTM ring burst testing. Issues with the testing protocol have limited assessment of these results. A prototype Type IV tank was designed to meet ANSI HGV2 standards, and the design criteria set out by DOE, using the CF properties developed by the team paired with a proprietary resin matrix, a polyamide liner, and aluminum end bosses. The tank weighs 153.1 kg and with a total capacity of 5.8 kg H2 (5.6 kg usable), which yields a gravimetric capacity of 1.17 kWh/kg. Cost modeling predicts that the tank will have a projected cost of $15.73/kWh. Tank performance modeling does not include considerations for fiber-matrix load transfer efficiency improvements offered by nanoparticle coating method.

08 HYDROGEN↗
DOE OSTI2024

1,4-cineole: a bio-derived solvent for highly stable graphene nanoplatelet suspensions and well-dispersed UHMWPE nanocomposite fibers

The exceptional properties of carbon nanoparticles, such as graphene, promise to expand the performance and functionality of many materials. The reinforcement of polymers is of keen interest due to their low density and flexible manufacturing methods. However, dispersing graphene in them has proven to be an enduring challenge due to the particles’ propensity to form performance degrading agglomerations. Furthermore, effective solvents for nanoparticle dispersion are commonly harmful, non-renewable, petrochemicals. In this work, a bio-derived solvent, 1,4-cineole, is demonstrated as a renewable alternative to these solvents that can be used to form highly stable graphene nanoplatelet (GnP) suspensions and used to gel spin well-dispersed UHMWPE/GnP nanocomposite fibers. The GnP concentration in the fibers was varied across three orders of magnitude, 0.01 wt% to 1 wt%, to examine its effect on fiber microstructure and properties. At low concentrations the particles act as point defects without affecting the fiber microstructure, and poor particle/matrix interfacial adhesion results in significantly reduced mechanical properties. At 1 wt% GnPs, a network effect takes hold thereby reinforcing the fibers, but the particles also impede the growth and orientation of crucial load-carrying crystalline structures in the fiber. Furthermore, unveiling the microstructural effects of GnPs on highly oriented and crystalline polymers in this study provides crucial insights for future work developing high-performance polymer nanocomposite fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The effect of stretching on polyamide – 6: assessment of crystallinity, mechanical properties, and surface roughness

Polyamide-6 (PA6), or nylon-6, is a widely used low-cost polymer material for various applications. Manufacturing PA6 into fibers involves a spinning process such as melt extrusion, which orients the polymer chains into a semicrystalline structure. When stretching the produced fibers to high strains, the PA6 fibers transition the metastable gamma phase back into the stable gamma phase. The effects of these large stretches on mechanical properties have not been explored after the stretch has been released. In this study, the effects on mechanical properties were studied by stretching the PA6 fibers from 10% to 50% tensile strain and subsequently releasing the fibers. The stretched fibers were characterized by X-ray diffraction and atomic force microscopy to determine the changes to the crystal structure and surface roughness. The stretched fibers were then tensile tested to failure and the tensile properties were examined. The stress-strain curves on the post-stretched PA6 fibers showed clear softening in the fibers with lower initial moduli after 30% stretching. Furthermore, these results may hold a clue to softening of fibers in applications with repeated loading and have implications for mechanical stability and fatigue of this polymeric material.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tuning Microstructure of Mesophase Pitch Carbon Fiber by Altering the Carbonization Ramp Rate

The microstructure of mesophase pitch carbon fibers (CFs) are tuned by varying ramp rates from 1 to 50 °C min –1 up to 1000 °C to study the effect of ramp rate on CFs’ microstructure, thermal and mechanical properties with the goal of offsetting the cost by decreasing cycle time. The ramp rates represent carbonization times ranging from 16.4 to 1.17 h, not including cool down. Differential scanning calorimetry, thermogravimetric analysis, and derivative thermogravimetry are used to investigate the impact ramp rate has on the thermal properties of mesophase pitch. It is found that lower ramp rates are endothermic in nature with a lower temperature onset and maximum weight loss. Higher ramp rates possess an exothermic nature with higher temperatures resulting in maximal weight loss over a smaller range of temperatures. Mechanical testing shows varying CF strengths and moduli dependent on ramp rate and an optimized process is developed to produce the strongest CF. Furthermore, microstructural characterization revealed that faster ramp rates lead to smaller interplanar spacings and larger crystallites but possessed greater disorder.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Evolution of Superconducting-Transition Temperature with Superfluid Density and Conductivity in Pressurized Cuprate Superconductors

What factors fundamentally determine the value of superconducting transition temperature T c in high temperature superconductors has been the subject of intense debate. Following the establishment of an empirical law known as Homes' law, there is a growing consensus in the community that the T c value of the cuprate superconductors is closely linked to the superfluid density (ρ s ) of its ground state and the conductivity (σ) of its normal state. However, all the data supporting this empirical law (ρ s = AσT c ) have been obtained from the ambient-pressure superconductors. In this study, we present the first high-pressure results about the connection of the quantities of ρ s and σ with T c , through the studies on the Bi 1.74 Pb 0.38 Sr 1.88 CuO 6+δ and Bi 2 Sr 2 CaCu 2 O 8+δ , in which the value of their high-pressure resistivity (ρ = 1/σ) is achieved by adopting our newly established method, while the quantity of ρs is extracted using Homes' law. In conclusion, we highlight that the T c values are strongly linked to the joint response factors of magnetic field and electric field, i.e., ρ s and σ, respectively, implying that the physics determining T c is governed by the intrinsic electromagnetic fields of the system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Evaluating consumer 3D printing nozzles as a low cost alternative for mesophase pitch-derived carbon fiber production

Synthetic fibers, such as Kevlar fibers, SiC fibers, and carbon fibers, are essential components for constructing high performance structures. Whether for engineering, sports, energy storage (batteries and supercapacitors), or aerospace applications, fiber microstructure plays a critical role in fiber properties and functionalities. However, studying fiber nozzle configurations and spinning parameters to achieve the desired microstructure remains challenging, costly, and time consuming. Here, mesophase pitch-derived fibers were used as an example to demonstrate that low cost, commercially available 3D printer nozzles can “print” fibers. Four different nozzles were used to “print” fibers and the effects of their features on fiber properties were observed and compared to other lab spun and commercial pitch- derived CF. A longer orifice length resulted in higher modulus fiber whereas a larger draw-down ratio yielded a stronger fiber. Furthermore, the findings provide a new opportunity for 3D printer hardware application and open up opportunities for developing low-cost fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Analysis of the turbostratic structures in PAN-based carbon fibers with wide-angle x-ray diffraction

Carbon fiber (CF) is a versatile material renowned for its excellent mechanical, thermal, and electrical properties. Polyacrylonitrile (PAN)-based CFs dominate the market due to their high tensile strength, rendering them suitable for structural applications in a wide variety of applications ranging from sporting goods to aerospace. Over five decades of commercial development of PAN-based CF has resulted in a range of varieties with different tensile moduli and tensile strengths. The microstructures, nanostructures, and crystal structures of PAN-based CF play pivotal roles in the macroscale properties of this material. In particular, the crystal structure and crystallite orientation in CF is closely related to the mechanical properties. The crystal structure of PAN-based CF generally consists of turbostratic carbon, which is a disordered form of graphite, the characteristics of which can be effectively characterized in a bulk format through wide-angle x-ray diffraction (WAXD). In this work, we employed a three-part approach to the analysis of WAXD patterns collected from four intermediate modulus PAN-based CFs. The approach incorporates a Scherrer analysis, a Debye analysis, and an orientational analysis to provide precise estimates of crystallite sizes, crystallite distributions, and crystallite orientations with the fiber axis. Furthermore, the results presented here suggest that intermediate modulus PAN-based CF mostly consists of small turbostratic crystallites (<4 nm), with larger crystallites having increased orientation with the fiber axis. The results here imply the presence of curvature and/or wrinkling of the turbostratic layers within the CF structure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ultra–high molecular weight polyethylene micro–ribbon fibers gel spun using orange terpenes

Toxic, hazardous petrochemical solvents are commonly used for industrial-scale ultra-high molecular weight polyethylene (UHMWPE) fiber production, but orange terpenes, a byproduct of orange fruit production, present a bio-derived, sustainable alternative. In this work, fine UHMWPE fibers were spun using orange terpenes as the spin solvent, hot-drawn at a draw ratio of 5:1, investigated for their morphology, microstructure, and thermal and mechanical properties. The resulting fibers exhibited a flat, micro-ribbon cross-section, which is highly desirable for achieving high fiber volume fractions in UHMWPE-fiber reinforced composites. After drawing, the fibers possessed 4× greater breaking tenacity than any previously published studies on UHMWPE fibers spun using orange terpenes with a tenacity of 8.6 cN/dtex and tensile modulus of 229.2 cN/dtex. Microstructural analysis via differential scanning calorimetry and X-ray diffraction revealed that the hot drawing process significantly increased molecular orientation, but crystallinity decreased due to crystallite melting during drawing. Therefore, the mechanical properties of these fibers may be significantly improved with optimization of the fiber drawing process. As a work, this work establishes the strong potential of orange terpenes as an environmentally-friendly alternative solvent for UHMWPE gel spinning and sets a foundation for future parametric optimization of the spinning and drawing of these fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of tension during sulfonation stabilization for UHMWPE-derived carbon fibers

Polyethylene is a promising low-cost alternative precursor material for carbon fiber production, but it has yet to show mechanical properties near or surpassing polyacrylonitrile-derived carbon fibers. The high molecular weight and order of ultra-high molecular weight polyethylene (UHMWPE) may offer a pathway to realizing this promise by enabling long-range graphitic structure formation and superior mechanical properties. The tension applied during the precursor stabilization process is crucial to maintaining the shape of the fibers during the conversion process, but no published study has yet probed the relationship between sulfonation tension and carbon fiber microstructure and mechanical properties. In this work, a logarithmic sweep of tensile stress was applied to UHMWPE fibers during the stabilization process followed by carbonization. Increasing tension significantly reduced fiber shrinkage, resulted in straighter fibers with less severe kink bands, and greatly improved the mechanical properties of the fibers. Raman spectroscopy and X-ray diffraction revealed that in all cases the carbon fibers were largely amorphous, but increasing tension resulted in increased size and alignment of the turbostratic crystallites with the fiber axis. Large voids were present in the sample fibers, so the Griffith-Irwin relation was employed to predict the potential ultimate tensile strength of the fibers with voids reduced to sizes comparable to commercially produced fibers. Furthermore, this work demonstrates the importance of tension applied during the stabilization of polyethylene fibers for carbon fiber production and establishes a framework for achieving high mechanical properties from these precursors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Exploration of fibers produced from petroleum based-mesophase pitch and pet blends for carbon fiber production

Petroleum-derived mesophase pitch and polyethylene terephthalate (PET) were blended and melt-extruded to create precursor fibers. The raw blends, heat treated bulk materials, and fibers were all examined to determine compatibility between petroleum-derived mesophase pitch and PET. Thermal investigation of the raw blends showed the presence of both the pitch and PET in separate phases suggesting no interactions had occurred during mixing. Here, the heat-treated bulk material also showed multiple phases under polarized light while Fourier-transform infrared spectroscopy indicated that the two materials did not fully separate during extrusion. Elemental scans of the precursor fibers showed areas of high oxygen concentrations averaging 11.7% as compared to a 2% oxygen concentration across the majority of the cross-section. Tensile tests of the precursor fibers showed a decrease in average modulus as compared to pure pitch fibers; however, the depressed modulus of the blended fibers was found to be independent of the PET weight percentage. Fibers created from 5 wt.% PET had a strength value within 10% of pure pitch and a 200% increase in modulus and were therefore found to be the most promising for carbon fiber production. Pure pitch and the 5 wt.% PET fibers were stabilized and carbonized to 1000 °C. Both types of fibers were tensile tested to determine their strength and stiffness. Pure pitch carbon fibers maintained a higher strength while the carbon fibers produced from 5 wt.% PET possessed a stiffer modulus which can be attributed to their radial microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of Oxygen Uptake on Pitch Carbon Fiber

Carbon fiber precursor materials, such as polyacrylonitrile, pitch, and cellulose/rayon, require thermal stabilization to maintain structural integrity during conversion into carbon fiber. Thermal stabilization mitigates undesirable decomposition and liquification of the fibers during the carbonization process. Generally, the thermal stabilization of mesophase pitch consists of the attachment of oxygen-containing functional groups onto the polymeric structure. In this study, the oxidation of mesophase pitch precursor fibers at various weight percentage increases (1, 3.5, 5, 7.5 wt%) and temperatures (260, 280, 290 °C) using in situ differential scanning calorimetry and thermogravimetric analysis is investigated. The results are analyzed to determine the effect of temperature and weight percentage increase on the stabilization process of the fibers, and the fibers are subsequently carbonized and tested for tensile mechanical performance. Finally, the findings provide insight into the relationship between stabilization conditions, fiber microstructure, and mechanical properties of the resulting carbon fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hierarchically Porous Carbons with Highly Curved Surfaces for Hosting Single Metal FeN 4 Sites as Outstanding Oxygen Reduction Catalysts

Iron–nitrogen–carbon (Fe₋N₋C) materials have emerged as a promising alternative to platinum-group metals for catalyzing the oxygen reduction reaction (ORR) in proton-exchange-membrane fuel cells. However, their low intrinsic activity and stability are major impediments. Herein, an Fe₋N–C electrocatalyst with dense FeN 4 sites on hierarchically porous carbons with highly curved surfaces (denoted as FeN 4 - hc C) is reported. The FeN 4 - hc C catalyst displays exceptional ORR activity in acidic media, with a high half-wave potential of 0.85 V (versus reversible hydrogen electrode) in 0.5 m H 2 SO 4 . When integrated into a membrane electrode assembly, the corresponding cathode displays a high maximum peak power density of 0.592 W cm -2 and demonstrates operating durability over 30 000 cycles under harsh H 2 /air conditions, outperforming previously reported Fe–N₋C electrocatalysts. These experimental and theoretical studies suggest that the curved carbon support fine-tunes the local coordination environment, lowers the energies of the Fe d-band centers, and inhibits the adsorption of oxygenated species, which can enhance the ORR activity and stability. This work provides new insight into the carbon nanostructure–activity correlation for ORR catalysis. It also offers a new approach to designing advanced single-metal-site catalysts for energy-conversion applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Pore connectivity influences mass transport in natural rocks: Pore structure, gas diffusion and batch sorption studies

For this work, six rocks (one granodiorite, one limestone, two chalks, one mudstone, and one dolostone) with different extents of heterogeneity at six different particle sizes (from 75 to 8000 μm) were studied to describe the effects of pore connectivity on mass transport. The methods applied were (i) porosity measurement of granular rocks, (ii) analyses of gas-phase diffusive transport in a bed of packed particles, along with a solid quartz method at these six particle sizes being developed to identify the contribution of intraparticle diffusion, and (iii) batch sorption tests of multiple ions (anions and cations) with subsequent analyses of inductively coupled plasma-mass spectrometry. Granular porosity measurement results reveal that with decreasing particle sizes, the effective porosities for the “heterogenous” group of rocks (Grimsel granodiorite and Edwards limestone) increase, whereas the porosities of another “homogeneous” group (two Israel chalk samples, Japan mudstone, and Wyoming dolostone) remain constant. Gas diffusion results show that the intraparticle gas diffusion coefficient among these two sample groups, varying in the magnitude of 10 -8 to 10 -6 m 2 /s, are not directly correlated to the porosity differences. Moreover, the batch sorption work displays a different affinity of rocks for various tracers. For Grimsel granodiorite, Japan mudstone, and Wyoming dolostone, the adsorption capacity of Sm 3+ and Eu 3+ increases as the particle size decreases. In general, this integrated research of grain size distribution, granular rock porosity, intraparticle diffusivity, and ionic sorption capacity gives insights into the pore connectivity effect on both physical and chemical transport behaviors for different lithologies and/or different particle sizes.

58 GEOSCIENCES↗
DOE OSTI2023

Compatibility of mesophase pitch and linear low-density polyethylene for low-cost carbon fiber

Mesophase pitch and linear low-density polyethylene (LLDPE) were blended by shear mixing and extruded producing precursor fibers which were then converted to carbon fibers (CFs). LLDPE additives agglomerate within the isotropic spheres rather than uniformly dispersing throughout the entire matrix. The blends possess different thermal properties and precursor tensile properties evident by two-phase tensile stress nature not present in precursor fibers produced from pure pitch. The resultant CFs were oxidized at 280 °C for 4 h and carbonized at 1000 °C for 15 min. This process created pitch CFs with a tensile strength of 1.23 GPa and a Young’s modulus of 99 GPa. All CFs produced from blends of pitch and LLDPE possessed a tensile strength of 0.63 GPa and less. These CFs showed a microstructure slightly different from the pure pitch CFs with fractured CF cross sections revealing voids present in all blended CFs due to burnt off LLDPE stemming from carbonization. Further study into compatibilizers and new conversion processes is required to successfully blend LLDPE with mesophase pitch for the purpose of producing a new low-cost CF.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Unveiling the microstructural evolution of carbon fibers derived from polyamide-6

Polyacrylonitrile-based carbon fibers have dominated the industry for decades, but the high cost of polyacrylonitrile has prevented the widespread adoption of carbon fiber in high-volume structural applications. As such, a significant amount of research has been dedicated to finding an alternative, low-cost carbon fiber precursor. In this work, carbon fibers were produced from polyamide-6 using metal salt impregnation and a thermo-oxidative stabilization step. To gain further insight into the carbonization process and microstructural transformation, the morphologies, crystallinities, elemental compositions, and thermal stabilities of the fibers were characterized at various stages of processing. The stabilization step resulted in a significant increase in carbon yield, indicating a dramatic increase in thermal stability. This is due to the crosslinking of polyamide-6 chains, which was confirmed by functional group analysis. The crystallinity of the fibers was also significantly altered during processing, as the produced carbon fibers consisted of pseudo-amorphous carbon with two distinct regions of metal salt impregnation. Finally, the findings and microstructural evolution mechanisms provide guidelines for further research into carbon fiber produced from polyamide-6.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Extracting single fiber transverse and shear moduli from off-axis misalignment fiber tensile testing

Small diameter (<100 μm) fibers (e.g. carbon fibers, Kevlar, and fiberglass) and wires (e.g. ultrafine copper and aluminum wires) are frequently used in many different engineering applications, such as for light weighting structures, electromagnetic shielding for aircraft/infrastructure/EVs, vibration damping, biological sensors, aerospace electrical devices, and electric windings just to name a few. Due to the manufacturing process, the fibers and wires are pulled and stretched to produce a preferential alignment. Therefore, thin fibers and wires typically display different properties along the length of the fiber as opposed to their cross section and many fibers/wires are considered transversely isotropic. The axial properties of fibers/wires can be ascertained via tensile testing of single-filaments or fiber tows, but the radial properties require much more effort to measure. Knowing these properties is important for the accurate prediction of micromechanical models and manipulation of fibers during micromanufacturing. In this paper, a new technique was developed to determine the transverse/shear moduli and strength of a material by conducting tensile tests of the material at increasing misalignment angles from the tensile axis. Due to the transversely isotropic nature of the material, the transverse/shear moduli and strength influence the experimental results recorded by the test machine to different degrees based on the amount of misalignment in the test setup. An equation was derived to determine the influence of each of the material properties based on the misalignment angle by manipulating the stiffness matrix for transversely isotropic materials using the transformation matrices. Then, curve fitted coefficients were used to identify the material properties. Here, the strengths were similarly determined by curve fitting an off-axis Tsai-Hill failure criteria to determine the influence of transverse, shear, and tensile strengths based on the complex loading condition provided by the off-axis tensile test. Zoltek Panex 35 carbon fibers were used to demonstrate this new technique and the determined properties were then compared to those obtained from nanoindentation and from literature. Fracture surfaces provide insight into the different failure mechanisms at various misalignment angles.

36 MATERIALS SCIENCE↗