Search NASA⌕ Search

Engineering topics

Li, Yat

Publications and source records attributed to Li, Yat.

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Interpenetrated Structures for Enhancing Ion Diffusion Kinetics in Electrochemical Energy Storage Devices

The architectural design of electrodes offers new opportunities for next-generation electrochemical energy storage devices (EESDs) by increasing surface area, thickness, and active materials mass loading while maintaining good ion diffusion through optimized electrode tortuosity. However, conventional thick electrodes increase ion diffusion length and cause larger ion concentration gradients, limiting reaction kinetics. We demonstrate a strategy for building interpenetrated structures that shortens ion diffusion length and reduces ion concentration inhomogeneity. This free-standing device structure also avoids short-circuiting without needing a separator. The feature size and number of interpenetrated units can be adjusted during printing to balance surface area and ion diffusion. Starting with a 3D-printed interpenetrated polymer substrate, we metallize it to make it conductive. This substrate has two individually addressable electrodes, allowing selective electrodeposition of energy storage materials. Using a Zn//MnO 2 battery as a model system, the interpenetrated device outperforms conventional separate electrode configurations, improving volumetric energy density by 221% and exhibiting a higher capacity retention rate of 49% compared to 35% at temperatures from 20 to 0 °C. Our study introduces a new EESD architecture applicable to Li-ion, Na-ion batteries, supercapacitors, etc.

25 ENERGY STORAGE↗
DOE OSTI2024

Interpenetrating 3D Electrodes for High-Rate Alkaline Water Splitting

Mass transfer is critical for the reaction kinetics and efficiency of alkaline water splitting (AWS). For AWS to operate at high current densities (hundreds of mA/cm 2 ), the device architecture must ensure a large catalytic surface area, rapid ion diffusion, and minimal solution and charge transfer resistances. Effective electrodes should also facilitate gas bubble detachment and release. 3D-printed electrodes have shown promise, but stacking them increases the ion diffusion length and solution resistance. Here we demonstrate a new device architecture with interpenetrating gyroid electrodes, providing a large ion-accessible surface area and gas diffusion channels. This design significantly reduces the interelectrode distance, lowering ion diffusion length and solution resistance. Simulations show faster ion diffusion and higher current density in the interpenetrating configuration compared with separate electrodes. This improved performance, especially at low temperatures and high current densities, highlights a promising strategy for enhancing AWS and other electrochemical systems limited by slow ion diffusion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Nanocone-Modified Surface Facilitates Gas Bubble Detachment for High-Rate Alkaline Water Splitting

The significant amount of gas bubbles generated during high-rate alkaline water splitting (AWS) can be detrimental to the process. The accumulation of bubbles will block the active catalytic sites and hinder the ion and electrolyte diffusion, limiting the maximum current density. Furthermore, the detachment of large bubbles can also damage the electrode's surface layer. Here, a general strategy for facilitating bubble detachment is demonstrated by modifying the nickel electrode surface with nickel nanocone nanostructures, which turns the surface into underwater superaerophobic. Simulation and experimental data show that bubbles take a considerably shorter time to detach from the nanocone-modified nickel foil than the unmodified foil. As a result, these bubbles also have a smaller detachment size and less chance for bubble coalescence. The nanocone-modified electrodes, including nickel foil, nickel foam, and 3D-printed nickel lattice, all show substantially reduced overpotentials at 1000 mA cm -2 compared to their pristine counterpart. The electrolyzer assembled with two nanocone-modified nickel lattice electrodes retains >95% of the performance after testing at ≈900 mA cm -2 for 100 h. In conclusion, the surface NC structure is also well preserved. The findings offer an exciting and simple strategy for enhancing the bubble detachment and, thus, the electrode activity for high-rate AWS.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2023

3D-Printed Graded Electrode with Ultrahigh MnO 2 Loading for Non-Aqueous Electrochemical Energy Storage

Electrolytic manganese dioxide is one of the promising cathode candidates for electrochemical energy storage devices due to its high redox capacity and ease of synthesis. Yet, high-loading MnO 2 often suffers from sluggish reaction kinetics, especially in non-aqueous electrolytes. The non-uniform deposition of MnO 2 on a porous current collectors also makes it difficult to fully utilize the active materials at high mass loading. Here, a 3D printed graded graphene aerogel (3D GA) that contains sparsely separated exterior ligaments is developed to create large open channels for mass transport as well as densely arranged interior ligaments providing large ion-accessible active surface. The unique structural design homogenizes the thickness of electro deposited MnO 2 even at an ultrahigh mass loading of ≈70 mg cm -2 . The electrode achieves a remarkable volumetric capacity of 29.1 mA h cm -3 in the non-aqueous electrolyte. A Li-ion hybrid capacitor device assembled with a graded 3D GA/MnO2 cathode and graded 3D GA/VO x anode exhibits a wide voltage window of 0–4 V and a superior volumetric energy density of 20.2 W h L -1 . The findings offer guidance on 3D printed electrode design for supporting ultrahigh loading of active materials and developments of high energy density energy storage devices.

electrochemical energy storage↗
DOE OSTI2023

High-performance aqueous zinc-ion hybrid capacitors based on 3D printed metal-organic framework cathodes

The zinc-ion hybrid capacitor is a promising energy storage device, but current overall capacity is limited by the capacitance of the carbon cathode. We have produced a hierarchically porous, nitrogen-doped carbon cathode with good cycling and mechanical stability by 3D printing and pyrolysis of the zinc-based metal–organic framework ZIF-8. When incorporated into a zinc-ion hybrid capacitor, we achieved an areal capacitance of 16.9 F cm -2 and energy density of 7.23 mW h cm -2 , outperforming zinc-ion hybrid capacitors based on conventional cathodes.

25 ENERGY STORAGE↗
DOE OSTI2023

Design and additive manufacturing of optimized electrodes for energy storage applications

Supercapacitors exhibit fast charging/discharging ability and have attracted considerable attention within the automotive, aerospace, and telecommunication industries. Porous carbons, prized for their high electrical conductivity and high surface area, have been attractive candidates for supercapacitor electrodes. Moving to thick electrodes is one strategy to further increase energy density due to a higher volume fraction of active material. However, thick electrodes suffer from sluggish charged species transport, which is why thin electrodes are currently favored. In this work, we investigate the use of computational optimization and additive manufacturing to design and fabricate thick porous electrodes with improved performance. Electrode performance was maximized by designing their morphologies via topology optimization and printing by projection micro stereolithography (PμSL) using commercial resin (PR48). The PR48 resin was then pyrolyzed (PR48-P) to create the final conductive electrode. The optimized PR48-P electrodes exhibited 99% improvement in capacitance compared to control electrodes printed with cubic lattice morphologies. To further improve performance, we formulated a resin combining graphene oxide (GO) and trimethylolpropane triacrylate (TMPTA). Electrodes printed with 3 wt% GO in TMPTA exhibited improved capacitance retention after pyrolysis compared to the PR48-P electrodes. Finally, this work demonstrates the benefits of using topology optimization to design electrodes and material development to improve functional properties of 3D printable electrodes.

25 ENERGY STORAGE↗