Search NASA⌕ Search

Engineering topics

Lieblein, Seymour

Publications and source records attributed to Lieblein, Seymour.

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

A 20,000-Kilowatt Nuclear Turboelectric Power Supply for Manned Space Vehicles

A conceptual design of a nuclear turboelectric powerplant, producing 20,000 kilowatts of power suitable for manned space vehicles is presented. The study indicates that the radiator necessary for rejecting cycle waste heat is the dominant weight, and emphasis is placed on the selection of cycle operating conditions in order to reduce this weight. A thermodynamic cycle using sodium vapor as the working fluid and operating at a turbine-inlet temperature of 2500 R was selected. The total powerplant weight was calculated to be approximately 6 pounds per kilowatt. The radiator contributes approximately 2.1 pounds per kilowatt to the total weight and the reactor and reactor shield contribute approximately 0.24 and 1.2 pounds per kilowatt, respectively. The generator, turbine, and piping add significantly to the total weight (between 0.5 and 0.6 lb/kw), but the heat exchanger, pumps, and so on are less important. Several important research areas associated with the development of a reliable nuclear turboelectric powerplant of the type analyzed are discussed.

English, Robert E.↗
NASA NTRS1957

Experimental investigation of an axial-flow-compressor inlet stage operating at transonic relative inlet Mach numbers V : rotor blade-element performance at a reduced blade angle

At a corrected speed of 1100 feet per second, the low-blade-angle rotor operated with a relative inlet Mach number of 1.2, a diffusion factor of 0.65, and an axial velocity ratio of 0.71 in the tip region (11 percent of passage height away from the outer wall). The measured minimum-loss coefficient was 0.35, and this value falls above a previous correlation of rotor losses with diffusion factor. Through a comparison with data for three other rotors, the occurrence of high losses was related to a high suction-surface Mach number. These comparisons also indicated that axial velocity ratios between 0.73 and 1.10 have no independent effect on losses.

Schwenk, Francis C↗
NASA NTRS1955

Aerodynamic Design of Axial-flow Compressors. VI - Experimental Flow in Two-Dimensional Cascades

Available experimental two-dimensional cascade data for conventional compressor blade sections are correlated at a reference incidence angle in the region of minimum loss. Variations of reference incidence angle, total-pressure loss, and deviation angle with cascade geometry, inlet Mach number, and Reynolds number are investigated. From the analysis and the correlations of the available data, rules and relations are evolved for the prediction of blade-profile performance. These relations are developed in simplified forms readily applicable to compressor design procedures.

Lieblein, Seymour↗
NASA NTRS1955

Aerodynamic Design of Axial-Flow Compressors. VII - Blade-Element Flow in Annular Cascades

Annular blade-element data obtained primarily from single-stage compressor installations are correlated over a range of inlet Mach numbers and cascade geometry. The correlation curves are presented in such a manner that they are related directly to the low-speed two-dimensional-cascade data of part VI of this series. Thus, the data serve as both an extension and a verification of the two-dimensional-cascade data. In addition, the correlation results are applied to compressor design.

Robbins, William H.↗
NASA NTRS1954

Review of high-performance axial-flow-compressor blade-element theory

This report presents a review of current compressor blade-element theory with particular emphasis on application to the transonic high-performance compressor. A discussion of the significant parameters of total-pressure loss and deviation angle is presented, and an indication of the extent of available knowledge and the problems involved in the determination of blade-element characteristics is given. Some recent results and considerations in this pursuit and suggestions for further avenues of investigation are indicated.

Lieblein, Seymour↗
NASA NTRS1951

Secondary flows in annular cascades and effects on flow in inlet guide vanes

Qualitative discussion is presented of the general nature of secondary flows in stationary annular cascades with thin wall boundary layers and radial design variation of circulation. Deviations from ideal mean outlet flows (based on blade-element performance) exist in potential-flow region of vanes because of conditions imposed by end-wall boundaries, displacement of wall boundary layers toward blade suction surfaces, and irrotationality requirement. As a consequence of existence of nonuniform radial flow across blade spacing, it may not generally be possible to obtain an arbitrarily specified design variation of the turning angle along the radial height of a blade row. Quantitative turning angle corrections due to effects of secondary flows in axial-flow compressor inlet guide vanes were obtained from induced deflections of a superimposed vortex system in conjunction with an empirically determined correlation factor.

CASCADES, EXPERIMENT↗