Engineering topics

Lin, Chin S.

Publications and source records attributed to Lin, Chin S..

6 records

NASA NTRS1996

Two-Phase Annular Flow in Helical Coil Flow Channels in a Reduced Gravity Environment

A brief review of both single- and two-phase flow studies in curved and coiled flow geometries is first presented. Some of the complexities of two-phase liquid-vapor flow in curved and coiled geometries are discussed, and serve as an introduction to the advantages of observing such flows under a low-gravity environment. The studies proposed -- annular two-phase air-water flow in helical coil flow channels are described. Objectives of the studies are summarized.

Keshock, Edward G.↗

NASA NTRS1996

Tank Pressure Control Experiment: Thermal Phenomena in Microgravity

The report presents the results of the flight experiment Tank Pressure Control Experiment/Thermal Phenomena (TPCE/TP) performed in the microgravity environment of the space shuttle. TPCE/TP, flown on the Space Transportation System STS-52, was a second flight of the Tank Pressure Control Experiment (TPCE). The experiment used Freon 113 at near saturation conditions. The test tank was filled with liquid to about 83% by volume. The experiment consisted of 21 tests. Each test generally started with a heating phase to increase the tank pressure and to develop temperature stratification in the fluid, followed by a fluid mixing phase for the tank pressure reduction and fluid temperature equilibration. The heating phase provided pool boiling data from large (relative to bubble sizes) heating surfaces (0.1046 m by 0.0742 m) at low heat fluxes (0.23 to 1.16 kW/sq m). The system pressure and the bulk liquid subcooling varied from 39 to 78 kPa and 1 to 3 C, respectively. The boiling process during the entire heating period, as well as the jet-induced mixing process for the first 2 min of the mixing period, was also recorded on video. The unique features of the experimental results are the sustainability of high liquid superheats for long periods and the occurrence of explosive boiling at low heat fluxes (0.86 to 1.1 kW/sq m). For a heat flux of 0.97 kW/sq m, a wall superheat of 17.9 C was attained in 10 min of heating. This superheat was followed by an explosive boiling accompanied by a pressure spike of about 38% of the tank pressure at the inception of boiling. However, at this heat flux the vapor blanketing the heating surface could not be sustained. Steady nucleate boiling continued after the explosive boiling. The jet-induced fluid mixing results were obtained for jet Reynolds numbers of 1900 to 8000 and Weber numbers of 0.2 to 6.5. Analyses of data from the two flight experiments (TPCE and TPCE/TP) and their comparison with the results obtained in drop tower experiments suggest that as Bond number approaches zero the flow pattern produced by an axial jet and the mixing time can be predicted by the Weber number.

Hasan, Mohammad M.↗

NASA NTRS1992

Simulation study of interactions of Space Shuttle-generated electron beams with ambient plasmas

This report summarizes results obtained through the support of NASA Grant NAGW-1936. The objective of this report is to conduct large scale simulations of electron beams injected into space. The topics covered include the following: (1) simulation of radial expansion of an injected electron beam; (2) simulations of the active injections of electron beams; (3) parameter study of electron beam injection into an ionospheric plasma; and (4) magnetosheath-ionospheric plasma interactions in the cusp.

Lin, Chin S.↗

NASA NTRS1991

SEPAC data analysis in support of the environmental interaction program

Data analyses of the Space Experiments with Particle Accelerators (SEPAC) data and computer modeling were conducted to investigate spacecraft environmental effects associated with injection of electron beams, plasma clouds, and neutral gas clouds from the Shuttle orbiter. The data analysis indicates that Extremely Low Frequency oscillations from 150 to 200 Hz were seen in the Langmuir probe current when the beam was fired in a continuous mode. The strongest oscillations occurred when the ambient pressure was augmented by neutral gas releases from the SEPAC plasma accelerator magnetoplasma-dynamic (MPD) arcjet. To understand the dependence of spacecraft charging potential on beam density and other plasma parameters, a two-dimensional electrostatic particle code was used to simulate the injection of electron beams from an infinite conductor into a plasma. The simulations show that the conductor charging potential depends critically on the reflection coefficient of the conductor surface, which is defined as the percentage of incident particles reflected by the conductor. The ionization effects on spacecraft charging were examined by including interactions of electrons with neutral gas. The simulations show that the conductor charging potential decreases with increasing neutral background density due to the production of secondary electrons near the conductor surface. The simulations also indicate that the beam radius is generally proportional to the beam electron gyroradius when the conductor is charged to a large potential. It appears that the charge buildup at the beam stagnation point causes the beam radial expansion. A survey of the simulation results suggests that the ratio of the beam radius to the beam electron gyroradius increases with the square root of beam density and decreases inversely with beam injection velocity. These results are useful for explaining the spacecraft charging phenomena observed during SEPAC experiments from Spacelab 1.

Lin, Chin S.↗

NASA NTRS1990

SEPAC data analysis in support of the environmental interaction program

Injections of nonrelativistic electron beams from an isolated equipotential conductor into a uniform background of plasma and neutral gas were simulated using a two dimensional electrostatic particle code. The ionization effects of spacecraft charging are examined by including interactions of electrons with neutral gas. The simulations show that the conductor charging potential decreases with increasing neutral background density due to the production of secondary electrons near the conductor surface. In the spacecraft wake, the background electrons accelerated towards the charged space craft produced an enhancement of secondary electrons and ions. Simulations run for longer times indicate that the spacecraft potential is further reduced and short wavelength beam-plasma oscillations appear. The results are applied to explain the space craft charging potential measured during the SEPAC experiments from Spacelab 1. A second paper is presented in which a two dimensional electrostatic particle code was used to study the beam radial expansion of a nonrelativistic electron beam injected from an isolated equipotential conductor into a background plasma. The simulations indicate that the beam radius is generally proportional to the beam electron gyroradius when the conductor is charged to a large potential. The simulations also suggest that the charge buildup at the beam stagnation point causes the beam radial expansion. From a survey of the simulation results, it is found that the ratio of the beam radius to the beam electron gyroradius increases with the square root of beam density and decreases inversely with beam injection velocity. This dependence is explained in terms of the ratio of the beam electron Debye length to the ambient electron Debye length. These results are most applicable to the SEPAC electron beam injection experiments from Spacelab 1, where high charging potential was observed.

Lin, Chin S.↗

NASA NTRS1989

Spacecraft charging potential during electron-beam injections into space plasmas

Injections of nonrelativistic electron beams from an infinite conductor have been simulated by using a two-dimensional electrostatic particle code to study the spacecraft charging potential. The simulations show that the conductor charging potential at the end of simulations does not vary with the beam density when the beam density exceeds four times the ambient density. The reflection coefficient, which determines a percentage of incident electrons reflected by the conductor, increases the charging potential. To charge the conductor to the beam energy, the reflection coefficient needs to be about 0.5. The results are applied to explain the spacecraft charging potential measured during the Sepac experiments on Spacelab 1.

Lin, Chin S.↗