Search NASA⌕ Search

Engineering topics

Lin, Lianshan

Publications and source records attributed to Lin, Lianshan.

At least 19 records

Delamination and Buckling Analysis of a Laminated Component in a High-speed Permanent Magnet Motor

High-speed permanent magnet (PM) machines are widely used because of their high-power density and high efficiency. The high rotation speed also inevitably subjects the PMs to high centrifugal load, which might damage them due to their inherent mechanical vulnerability, such as a much lower tensile strength than the compressive strength. To robustly transfer the torque from the magnet to the shaft, the outer diameter of the laminated rotor core is larger than the inner diameter of the rotor frame to ensure tight contact while working at 20,000 rpm. Motor manufacturing requires the shrink-fit method to assemble the rotor frame and rotor core. However, after the shrink-fit assembly, unexpected local delamination and buckling are observed on the rotor core part. Utilizing finite element simulation, we study the internal stress of assembling these two parts at the provided interference. Simulation results indicate the reasons for the delamination and buckling of the rotor core part and provide suggestions for improving the assembly.

Lin, Lianshan↗

Study of a High-speed Outer Rotor Burst Containing Enclosure

The increasing demand for high-speed electric machines in many applications pushes the development of high-power density electric motors. Outer rotor motors, which can be designed with a larger airgap diameter than inner rotor motors for the same overall diameter and, therefore, provide higher torque, distinguish themselves in space-constrained but high torque applications. However, increasing the motor speed and diameter results in significant centrifugal loads for the outer rotor motor due to its higher airgap diameter. Additional attention must be paid at the design stage to consider the extreme situation of possible mechanical failure, such as the sudden burst of the high-speed rotating parts in the motor, and measures must be taken to prevent their damage to other system components in advance. Through the finite element dynamic impact analysis, we studied the damage caused by broken parts on the inner wall of the electric motor housing when the motor rotates at 20,000 RPM. The proposed method is expected to provide reasonable recommendations of the enclosure material and its thickness required to protect other components in the same powertrain system when the high-power density motor fails unexpectedly.

Lin, Lianshan↗

Dataset of mechanically induced thermal runaway measurement and severity level on Li-ion batteries

The deployment of Li-ion batteries covers a wide range of energy storage applications, from mobile phones, e-bikes, electric vehicles (EV) and stationary energy storage systems. However, safety issue such as thermal runaway is always one of the most important concerns to prevent Li-ion batteries from further market penetration. A standardized single-side indentation test protocol was developed to mechanically induce an internal short-circuit. The cell voltage, compressive load, indenter stroke, and temperature at the indentation point are measured in time series. The test data of each cell, along with cell parameters such as dimensions, mass, chemistry, state of charge (SOC), capacity, are integrated together to calculate a thermal runaway severity score from 0 to100. Complete data collection process including the original measured record, test method, severity score calculation scheme is presented in this article. The thermal runaway severity analysis and the more than 100 tested Li-ion battery records provide a good data source for further comparison and ranking of thermal runaway risks.

25 ENERGY STORAGE↗

Rotordynamic Analysis and Comparative Study of High-Speed Outer Rotor Permanent Magnet Motor Designs

High–power density electric motor designs are a requirement in aerospace and automotive applications. Outer rotor permanent magnet motors can offer high power density but have mechanical challenges such as structural stability and rotodynamic issues. In this work, a rotodynamic study was performed for two outer rotor permanent magnet motor designs. The first design was a cantilever design in which the rotor was suspended at one end, supported by four bearings; in the second design, the rotor was simply supported by two bearings in each end. Two different finite element method–based approaches, solid rotor and beam rotor methods, were used to extract the critical speed.

Barua, Himel↗

Crack Propagation Modeling of a High-Speed Outer Rotor Motor

This study aims to investigate the propagation of initial cracks in electric motors and their rate of spread through the rotor structure under various operating conditions. Traction motors are subjected to high centrifugal load owing to their speed and rapid acceleration and deceleration. In the manufacturing process, some initial imperfections or cracks in the rotor components are likely to occur. Under the influence of loading, these cracks will grow, and factors such as loading frequency, material strength, and location of material voids will affect this threshold speed. In the current study, a fracture mechanics–based approach has been used to investigate the crack growth rate for a 100 kW outer rotor motor with a rated speed of 6,000 rpm and a peak speed of 20,000 rpm for an integrated drive application.

Barua, Himel↗

A new perspective on density and strength loss profiles at the surface of thermally oxidized nuclear graphite

Oxidation of graphite components could influence their designed life in a high-temperature nuclear reactor. The oxidized regions could potentially lower the allowed stress capacity. The American Society of Mechanical Engineers rules for the design and construction of graphite-moderated reactors recommend that subsurface regions that might become excessively damaged by oxidation during reactor operation be identified and excluded from geometry and stress calculations. Identification of oxidation-affected regions is possible, in principle, through complex modeling exercises of reactor behavior during hypothetical accident scenarios coupled with graphite oxidation models, but this procedure may not have the precision needed for informed decisions. Here, this paper proposes an alternate method, based on interpretation of a series of well-designed oxidation experiments, which could augment the designer's tools. The procedure is illustrated by data on oxidation by air of several graphite grades (NBG-18, PCEA, IG-110, R4-650) that are corroborated with independent literature information, when available. The Wichner model for graphite oxidation used for this analysis provides conservative results that could be quickly implemented in the design process.

36 MATERIALS SCIENCE↗

Effect of Sample Thickness on the Tensile Strength of Small Graphite Discs

This report formally documents the completion of the Advanced Reactor Technologies (ART) Level 3 Milestone (M3TG-24OR0501054), “Continue activities related to Split Disc-DIC - complete analysis of effect of sample thickness on one fine grain graphite,” due May 31, 2024. Details within this report outline the status of activities aimed at elucidating the effect of sample thickness on the tensile strength measurement using the small-disc, split-disc testing standard in support of the US Department of Energy’s ART Graphite R&D Program. The ASTM D8289, Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite, was developed to provide an alternative means for testing tensile strength on smaller specimens, which are compatible with available irradiation capsule volumes, and other compatibility measurements. ASTM D8289 specifies that acceptable specimen diameter can range from 6 to 12.7 mm and that the maximum allowed sample thickness should be half of the diameter. However, information is limited with respect to the effect of thickness on the measured splitting tensile strength. This report documents efforts to understand the effect of sample thickness on splitting tensile strength. The work involved testing Ø12.7 mm samples of fine-grain graphites 2114 and IG-110 of different thicknesses (6.35, 5, 4, and 3 mm). The digital image correlation (DIC) method was applied to the samples, along with the ASTM D8289 Standard, to help interpret the measured results.

36 MATERIALS SCIENCE↗

Development of a self-lubricating high-efficiency hybrid seal composed of carbon nanotube-coated metal meshes for CSP turbomachinery (SETO CPS #36333 Final Report)

In turbomachinery, internal leakage flow accounts for up to 3% of the total thermodynamic cycle energy loss. Tradeoff must be made between the sealing efficiency (smaller clearance) and the friction and wear issues for interfering with the shaft (larger clearance). This ORNL-Danfoss joint effort developed a novel hybrid seal composed of carbon nanotube (CNT)-coated metal meshes. The CNT growth process was based on a self-catalyzing chemical vapor deposition and these multiwall CNTs were well aligned with high crystallinity. This hybrid material structure takes advantage of the CNT’s low-friction nature and uses the metal mesh as an extendable backbone. Full-scale experimental seals were designed, fabricated, and optimized for sealing performance and durability. The CNT-coated metal mesh seal demonstrated superior gas sealing efficiency to the baseline labyrinth seal and significantly improved shaft surface protection compared with the state-of-the-art superalloy brush seal on the static rig and full-scale compressor dynamometer tests. The CNT-metal mesh seal is low-cost and scalable and can potentially benefit wide applications, including CSP and other power generation, marine, automotive, and HVAC.

36 MATERIALS SCIENCE↗

Finite Element Modeling of the Phase Change in Thermally-Grown SiO 2 in SiC Systems for Gas Turbines

The operating lifetimes of SiC-based components in combustion environments are directly linked to the adhesion of the protective environmental barrier coating (EBC) layer. One of the major known failure modes for EBCs is the formation of a thick SiO 2 thermally grown oxide (TGO), which decreases coating adhesion and encourages eventual coating spallation. The effect of the TGO thickness under Yb 2 Si 2 O 7 EBCs on silicon carbide was investigated using finite element models (FEMs) with various interfacial architectures and SiO 2 TGO thicknesses. Further, the FEMs incorporated a user-defined material to simulate the volume contraction of the TGO during the silica phase transformation from β-cristobalite to α-cristobalite upon cooling from the stress-free state at 1350°C to room temperature. Systems with and without a silicon bond coating intermediary layer were assessed. It was shown that the TGO phase transformation stress (1.6–1.7 GPa) dominated the increase in stress in the TGO and EBC layers. Furthermore, it was found that stress increase in the TGO was independent of TGO thickness and interface geometry. These results indicate that stabilization of the TGO to mitigate the phase transformation could dramatically improve the performance of SiC-base components with EBCs.

36 MATERIALS SCIENCE↗

Material Model Parameters Optimization in Liquid Mercury Target Dynamics Simulation With Machine Learning Surrogates

A pulsed spallation target is subjected to very short (∼0.7μs) but intense loads (23.3 kJ) from repeated proton pulses, which knock away neutrons from the mercury atoms’ nuclei for a wide range application in physics, engineering, medicine, petroleum exploration, biology, chemistry, etc. The effect of this pulsed loading on the stainless-steel target module which contains the flowing mercury target material is difficult to predict not only due to its short but intense explosive-like physical reaction, but also the nonlinear material behavior of the liquid mercury in the structure. Injecting small helium bubbles in the mercury has been an efficient method of mitigating the pressure wave at high power level stage. However, prediction of the resultant loading on the target is more difficult when helium gas is intentionally injected into the mercury. A 2-phase material model that incorporates the Rayleigh-Plesset (R-P) model is expected to address this complex multi-physics dynamics problem by including the bubble dynamics in the liquid mercury. A parameter sensitivity study was firstly employed to understand their impact on the simulation strains. The investigated parameters included E, μ, γ, σ, n, VFgas, and gas cumulative volume curve control parameters a and b. Verification and validation results from sparse polynomial expansions (SPE) method and directional Gaussian smoothing (DGS) optimization show that the surrogate model had training error of ∼7% and validation error of ∼15%, indicating that machine learning methods and surrogate models can help optimize the uncertain parameters in the complex 2-phase material model. This approach is expected to fill the knowledge gap between unknown liquid-gas mixture material model and measured vessel strain responses.

Lin, Lianshan↗

Calibration of the 2-Phase Bubble Tracking Model for Liquid Mercury Target Simulation with Machine Learning Surrogate Models

The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory is one of the most powerful accelerator-driven neutron sources in the world. The intense protons strike on SNS's mercury target to provide bright neutron beams, which also leads to severe fluid-structure interactions inside the target. Prediction of resultant loading on the target is difficult particularly when helium gas is injected into mercury to reduce the loading and mitigate the pitting damage on vessel walls. A 2-phase material model that incorporates the Rayleigh-Plesset (R-P) model is expected to address this multi-physics problem. However, several uncertain parameters in the R-P model require intensive simulations to determine their optimal values. With the help of machine learning and the measured target strain, we have studied the major uncertain parameters in this R-P model and developed a framework to identify optimal parameters that significantly reduce the discrepancy between simulations and experimental strains. The preliminary results show the possibility of using this mercury/helium mixture and surrogate models to predict a better match of target strain response when the helium gas is injected.

Lin, Lianshan↗

An Integrated Traction Drive with a High Speed Surface Permanent Magnet External Rotor Motor for Electric Vehicles

This work presents the detailed design of an outer rotor motor and integrated drive for passenger electric vehicles. The motor uses non-heavy rare earth permanent magnets and operates at a top speed of 20,000rpm. In-slot ceramic heat exchangers are utilized for the cooling of the windings. The external rotor configuration of the motor leaves a significant amount of space in the stator bore, which is leveraged for the integration of the power electronics. A high speed external rotor motor creates a number of mechanical, thermal and assembly challenges and this work presents detailed thermal, mechanical and rotordynamics analysis.

ADVANCED PROPULSION SYSTEMS↗

Mechanical Analysis of Carbon Fiber Retaining Sleeve for A High-speed Outer Rotor SPM Electric Motor Design

Outer rotor motors can be designed with a larger airgap diameter than inner rotor motors for the same overall diameter and therefore provide higher torque which makes them ideal for high torque space constrained applications. This advantage fits well with the increasing demand of high-speed electric machines in many applications due to their inherent high-power density. However, increasing the motor speed results in significant centrifugal loads for the outer rotor motor design. Layers of carbon fiber sleeve winding on the rotor outer surface is necessary to guarantee its structural integrity without introducing too much weight on the motor itself. In this paper, we studied the mechanical stress of a carbon fiber retaining sleeve in a surface permanent magnet outer rotor motor that spins up to 20,000 RPM. Analytical results from finite element method (FEM) confirmed that the maximum stress experienced by the carbon fiber sleeve was under the material’s yield strength. The proposed sleeve will allow this outer rotor motor to operate at high speeds.

Lin, Lianshan↗

Mechanical behavior analysis using small-size graphite disc compression testing with digital image correlation methods

The ASTM International Standard Test Method for Tensile Stress-Strain of Carbon and Graphite (ASTM C749) requires dog-bone shaped specimens. Unfortunately, specimen sizes required in ASTM C749 are much too large for irradiation within a test reactor and are incompatible with irradiation capsule volumes, molten salt degradation facilities, or oxidation apparatus. The ASTM International Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite (ASTM D8289) was developed as an alternative that provides a means for testing tensile properties using smaller specimens when geometric constraints are present. However, the important stress–strain relation throughout the test loading history that could be recorded using ASTM C749 is lost by using ASTM D8289 because of the difficulties involved with using traditional strain gauges or extensometers on such a small specimen. In this work, a digital image correlation (DIC) method, which uses a full-field noncontact surface displacement measurement technique, was applied along with the ASTM D8289 splitting tensile test on eight small samples of graphite grade Mersen 2114 to track their deformation during compressive loading. Initial results showed that the DIC technique can measure the surface displacement/strain on these small (Ø6 × 3 mm) graphite specimens with high accuracy and good repeatability, indicating that the DIC technique, combined with the small-disc splitting tensile test in ASTM D8289, can capture the strain evolution in the test. In conclusion, further comparison of measured strains with analytical and numerical simulation results provides additional understanding of the mechanical behaviour of this nuclear graphite material in complex stress states.

36 MATERIALS SCIENCE↗

Contact pressure analysis to allow improved design for the clearing plate in a biomass comminution system

For biomass processing systems, feedstocks with small but equal sizes can improve flowability and thermochemical outputs. The Crumbler rotary shear system was designed to achieve such ideal feedstocks to reduce costs and energy throughout the biomass supply chain. Improving the wear resistance of major components in this system is important to decrease the cost. Accelerating the feedstock flow through the rotary shear machine plays an equivalent role of improving its efficiency. An analytical analysis and a finite-element analysis of the stationary clearing plate are presented in this work. Here, these tools are used to investigate the effect of contact surface curvature on the impact pressure. The optimized new clearing plate design is expected to improve the component’s lifetime and wood chips flowability. The field tests confirm that the trend of the new clearing plate design guided by FEA. The optimization method, model verification, and validation experience applied in this work can also be applied to other static components with similar simple contact wear problems.

09 BIOMASS FUELS↗

Initial Assessment of Erosion/Abrasion Issues Related to Gas-Cooled Reactors

The US Department of Energy’s Oak Ridge National Laboratory (ORNL) is investigating the graphite erosion concern detailed in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC), Section III, Division 5, “High Temperature Reactors.” The special consideration in Subsection HH, Subpart A (HHA)-3143, “Abrasion and Erosion,” was described in ASME BPVC Section III, Division 5, which was accepted with exception/limitation in a US Nuclear Regulatory Commission (NRC) Technical Review. This report describes ORNL’s FY 2023 comprehensive research of erosion-related reports and publications to further study the proposed gas flow velocity limitation to the erosion effect in graphite structure in the ASME BPVC. This report also proposes that a nondimensional fluid parameter, the Reynolds number, might be a better alternative than gas flow velocity for comparing erosion effects caused by carbonaceous dust in fast-flowing helium coolant in gas-cooled reactors (GCRs).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigation of Biomass Fouling on Screw Feeder in Preconversion of Pyrolysis

Biomass is a source of renewable energy and can undergo thermochemical processes to be converted into gaseous and liquid fuels. Thermal decomposition-induced biomass fouling on the screw feeder is a major challenge in preconversion of pyrolysis, leading to plugging of the feed line. Here, this work intends to gain fundamental understanding of the biomass fouling phenomena across the heat gradient on the screw feeder via a combination of materials characterization and thermal simulation. An actual screw feeder that failed because of biomass fouling was examined to reveal the deposit’s morphology, composition, and mechanical properties. Thermal simulations were developed for both the screw feeder and the wood particles being transported using a combined analytical and numerical approach. The simulated temperature profiles correlated well with the deposit observations, based on which potential mitigations were proposed from both the operation and screw design perspectives and supported by preliminary experimental validation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗