Engineering topics

Lin, X.

Publications and source records attributed to Lin, X..

7 records

DOE OSTI2024

Turbulence spreading effects on the ELM size and SOL width

BOUT++ turbulence simulations were performed to investigate the impact of turbulence spreading on the edge localized mode (ELM) size and divertor heat flux width (λ q ) broadening in small ELM regimes. Here, this study is motivated by EAST experiments. BOUT++ linear simulations of a pedestal radial electric field (E r ) scan show that the dominant toroidal number mode (n) shifts from high-n to low-n, with a narrow mode spectrum, and the maximum linear growth rate increases as the pedestal E r well deepens. The nonlinear simulations show that as the net E × B pedestal flow increases, the pressure fluctuation level and its inward penetration beyond the top of the pedestal both increase. This leads to a transition from small ELMs to large ELMs. Both inward and outward turbulence spreading are sensitive to the scrape-off-layer (SOL) plasma profiles. The inward turbulence spreading increases for the steep SOL profiles, leading to increasing pedestal energy loss in the small ELM regime. The SOL width (λ q ) is significantly broadened progressing from the ELM-free to small ELM regime, due to the onset of strong radial turbulent transport. The extent of the SOL width (λ q ) broadening depends strongly on outward turbulence spreading. The fluctuation energy intensity flux Γ ε at the separatrix can be enhanced by increasing either pedestal E r flow shear or local SOL pressure gradient. The λ q is broadened as the fluctuation energy intensity flux Γ ε at the last close flux surface (LCFS) increases. Local SOL E × B flow shear will restrain outward turbulence spreading and the associated heat flux width broadening. Operating in H-mode with small ELMs has the potential to solve two critical problems: reducing the ELM size and broadening the SOL width.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Impact of pedestal density gradient and collisionality on ELM dynamics

BOUT++ turbulence simulations are conducted to capture the underlying physics of small ELM characteristics achieved by increasing separatrix density via controlling strike points from vertical to horizontal divertor plates for three EAST discharges. BOUT++ linear simulations show that the most unstable modes change from high-n ideal ballooning modes to intermediate-n peeling–ballooning modes and eventually to peeling–ballooning stable plasmas in the pedestal. Nonlinear simulations show that the fluctuation is saturated at a high level for the lowest separatrix density. The ELM size decreases with increasing separatrix density, until the fraction of this energy lost during the ELM crash becomes less than 1% of the pedestal stored energy, leading to small ELMs. Simulations indicate that small ELMs can be triggered either by the marginally peeling–ballooning instability near the peak pressure gradient position inside the pedestal or by a local instability in the pedestal foot with a larger separatrix density gradient. The pedestal collisionality scan for type-I ELMs with steep pedestal density gradient shows that both linear growth rate and ELM size decrease with increasing collisionality. On the contrary, the pedestal collisionality and pedestal density width scan with a weak pedestal density gradient indicate small ELMs can either be triggered by a high-n ballooning mode or by a low-n peeling mode in a low collisionality region 0.04–0.1. We report the simulations indicate the weaker the linear unstable modes near marginal stability with small linear growth rate, the lower nonlinearly saturated fluctuation intensity and the smaller turbulence spreading from the linear unstable zone to stable zone in the nonlinear saturation phase, leading to small ELMs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Physical mechanisms for the transition from type-III to large ELMs induced by impurity injection on EAST

Transition from type-III to large-amplitude ELMs induced by neon injection has been observed in the EAST tokamak at overlapping q 95 space between large and small ELMs. With neon injection, pedestal density gradient shows a remarkable increase accompanied by some decrease of pedestal electron temperature, and consequently the pressure gradient increases moderately and edge bootstrap current has minimal change. Further experiment demonstrates that the occurrence of large ELMs after neon injection is highly correlated with the change in edge density. Linear peeling-ballooning stability analysis indicates that the large ELM case is more unstable than the type-III ELM case during the ELM transition. A scan of pedestal density gradient in linear stability analysis shows that the direct destabilizing effect of steep pedestal density gradient on peeling-ballooning instabilities via two-fluid effects could also facilitate the transition to large ELMs. In conclusion, these results could provide more insight into the role of pedestal density gradient on pedestal stability and ELM behavior.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Sustained edge-localized-modes suppression and radiative divertor with an impurity-driven instability in tokamak plasmas

We report simultaneous control of the large edge localized modes (ELMs) and divertor heat fluxes in a metal wall environment is a critical issue for steady-state operation of a tokamak fusion reactors. Here we report a sustained ELM suppression scenario achieved in the EAST tokamak compatible with radiative divertor using different seeding impurity species over a wide range of conditions. A low-n mode appears, as manifested by the oscillations of a radiation front near the X-point. This mode appears to drive strong particle transport and tungsten exhaust, which is essential to the maintenance of the ELM-stable state. We have developed a model to explain the mode excitation, by coupling the impurity radiative condensation instability to drift waves, which could explain some characteristics of the low-n mode well. The low-n mode may offer a new ELM-stable scenario compatible with radiative divertor for future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Type-I ELM mitigation by continuous lithium granule gravitational injection into the upper tungsten divertor in EAST

Large edge-localized modes (ELMs) were mitigated by gravitational injection of lithium granules into the upper X-point region of the experimental advanced superconducting tokamak (EAST) device with tungsten plasma-facing components. The maximum ELM size was reduced by ~70% in high β N H-mode plasmas. Large ELM stabilization was sustained for up to about 40 energy confinement times, with constant core radiated power and no evidence of high-Z or low-Z impurity accumulation. The lithium granules injection reduced the edge plasma pedestal density and temperature and their gradients, due to increased edge radiation and reduced recycling from the plasma-facing components. Ideal stability calculations using the ELITE code indicate that the stabilization of large ELMs correlates with improved stability of intermediate-n peeling-ballooning modes, due to reduced edge current resulting from the profile changes. The pedestal pressure reduction was partially offset by a core density increase, which resulted in a modest ~7% drop in core stored energy and normalized energy confinement time. We surmise that the remnant small ELMs are triggered by the penetration of multiple Li granules just past the separatrix, similar to small ELMs triggered by deuterium pellet Futatani et al (2014 Nucl. Fusion 54 073008). This study extends previous ELM elimination with Li powder injection Maingi et al (2018 Nucl. Fusion 58 024003) in EAST because (1) use of small, dust-like powder and the related potential health hazards were eliminated, and (2) use of macroscopic granules should be more applicable to future devices, due to deeper penetration than dust particles, e.g. inside the separatrix with velocities ~10 m s -1 in EAST.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Stabilizing effect of enhanced resistivity on peeling-ballooning instabilities on EAST

Previous stability analysis of NSTX equilibrium with lithium-conditioning demonstrates that enhanced resistivity due to the increased effective charge number Z eff (i.e. increased impurity level) can provide a stabilizing effect on low-n edge localized modes. This paper extends the resistivity stabilizing effect to the intermediate-n peeling-ballooning (PB) instabilities with the linear stability analysis of EAST high-confinement mode equilibria in NIMROD two-fluid calculations. However, in this work, the resistivity stabilizing effect on PB instabilities in the EAST tokamak appears weaker than that found in NSTX. This work may provide better insight into the physical mechanism behind the beneficial effects of impurities on pedestal stability.

EAST tokamak↗

NASA NTRS2006

Simulated convective systems using a cloud resolving model: Impact of large-scale temperature and moisture forcing using observations and GEOS-3 reanalysis

The GCE (Goddard Cumulus Ensemble) model, which has been developed and improved at NASA Goddard Space Flight Center over the past two decades, is considered as one of the finer and state-of-the-art CRMs (Cloud Resolving Models) in the research community. As the chosen CRM for a NASA Interdisciplinary Science (IDS) Project, GCE has recently been successfully upgraded into an MPI (Message Passing Interface) version with which great improvement has been achieved in computational efficiency, scalability, and portability. By basically using the large-scale temperature and moisture advective forcing, as well as the temperature, water vapor and wind fields obtained from TRMM (Tropical Rainfall Measuring Mission) field experiments such as SCSMEX (South China Sea Monsoon Experiment) and KWAJEX (Kwajalein Experiment), our recent 2-D and 3-D GCE simulations were able to capture detailed convective systems typical of the targeted (simulated) regions. The GEOS-3 [Goddard EOS (Earth Observing System) Version-3] reanalysis data have also been proposed and successfully implemented for usage in the proposed/performed GCE long-term simulations (i.e., aiming at producing massive simulated cloud data -- Cloud Library) in compensating the scarcity of real field experimental data in both time and space (location). Preliminary 2-D or 3-D pilot results using GEOS-3 data have generally showed good qualitative agreement (yet some quantitative difference) with the respective numerical results using the SCSMEX observations. The first objective of this paper is to ensure the GEOS-3 data quality by comparing the model results obtained from several pairs of simulations using the real observations and GEOS-3 reanalysis data. The different large-scale advective forcing obtained from these two kinds of resources (i.e., sounding observations and GEOS-3 reanalysis) has been considered as a major critical factor in producing various model results. The second objective of this paper is therefore to investigate and present such an impact of large-scale forcing on various modeled quantities (such as hydrometeors, rainfall, and etc.). A third objective is to validate the overall GCE 3-D model performance by comparing the numerical results with sounding observations, as well as available satellite retrievals.

Shie, C.-L.↗