Engineering topics

Lin, Yu-Chung

Publications and source records attributed to Lin, Yu-Chung.

6 records

DOE OSTI2024

Template-Assisted Growth of High-Quality α-Phase FAPbI 3 Crystals in Perovskite Solar Cells Using Thiol-Functionalized MoS 2 Nanosheets

Formamidinium lead iodide (FAPI) has gained attention for hybrid perovskite solar cell (PSC) applications due to its enhanced stability and narrow bandgap. However, a significant challenge remains in inducing and stabilizing the elusive perovskite “black phase”—photoactive cubic α-FAPI—as the relatively bulky FA + cations tend to favor the thermodynamically stable nonphotoactive “yellow phase”. Here, in this study, we present a templated growth strategy employing thiol-functionalized MoS 2 nanosheets as templates. By introduction of 3-mercaptopropionic acid (MPA)-functionalized MoS 2 as a growth template, precise control over crystal formation was achieved, favoring the growth of high-quality α-FAPI films. These advanced templated films exhibited substantial improvements in charge transport properties, efficient light absorption, and enhanced charge extraction. As a result, the PSCs achieved a significantly enhanced power conversion efficiency (PCE) compared to the nontemplated control device, increasing from 20.6 to 22.5%. The MoS 2 -incorporated device also demonstrated excellent shelf stability, maintaining 91% of the initial PCE even after 1600 h of storage without device encapsulation.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Determination of the Interfacial Energy between Graphene Nanoplatelets and Deuterated or Hydrogenated Polystyrene

The tracer diffusion coefficients of various graphene nanoplatelet-polystyrene (GNP-PS) systems were determined by using dynamic secondary ion mass spectrometry, which provided insights into the interactions within the polymer nanocomposite system. Bilayer films, where one contained trace amounts of deuterated polystyrene (dPS), were produced, and the interdiffusion was measured by detecting the position of the dPS interface. GNPs were placed in both or only one of the two layers. The diffusion coefficient was decreased when GNPs were present in both layers as compared to the samples without GNP, indicating an attractive interaction between GNP and polystyrene. Surprisingly, the coefficient increased relative to the control when GNPs were present only in the PS containing layer, whereas it decreased most strongly when GNP and dPS were present only in the same layer, indicating that an additional preference existed for GNPs and dPS. A significant difference in interfacial energies was measured using contact angle goniometry of PS or dPS droplets on flat GNP layers, confirming the preferential interaction. DFT calculations were used to calculate the interfacial interaction between GNP and dPS or PS, and they showed an attractive potential which was maximal when the PS rings were conformal with the GNP structure. Furthermore, the differential energy between PS and dPS at the GNP interface was in excellent agreement with the measured value. In contrast, contact angle goniometry indicated that the interaction between GNP and poly(methyl methacrylate) (PMMA) was unfavorable, and no difference in interfacial energy between dPMMA and PMMA was observed. Therefore, these techniques can provide a means for determining the relative affinity between GNP and different polymer hosts, which can be an important consideration in the mechanics and adhesion properties of the compounds.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Application of the core shell model for strengthening polymer filament interfaces

While surface segregation has been intensively studied in thin films, relatively little has been investigated in filament geometries. In contrast to thin films, the filament surface forms a continuum, with interactions both at the free air and internal filament interface, which makes it difficult to achieve an equilibrium configuration. This asymmetry has become particularly apparent with the increasing use of additive manufacturing where entire structures are constructed via layered deposition of filamentous layers from a moving thermal nozzle. In addition, this process is highly non-equilibrated with poor thermal retention and is responsible for insufficient filament–filament interfacial fusion and internal pore formation along the printing direction. These features all contribute to poor mechanical and structural properties, which are exacerbated in semi-crystalline polymers, such as Polylactic Acid (PLA), where the melting point, T m , is much higher than the glass transition, T g . Even though system is liquid the molecules become ordered within the crystal structure and this ordering interferes with interdiffusion, which in turn prevents proper interfacial fusion. Capitalizing on the differential in surface tension, we show that addition of less than 1%, or trace amounts, of longer chain polymers, an oriented core shell structure, will be formed with a self-limiting thickness of three time the radius of gyration, R g , of the tracer chains. The lower T g of the tracers and their orientation makes them poised for interdiffusion when subsequent layers are deposited producing structures with significant improvement of the mechanical properties and internal structural integrity.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Nano- to microscale three-dimensional morphology relevant to transport properties in reactive porous composite paint films

The quantitative evaluation of the three-dimensional (3D) morphology of porous composite materials is important for understanding mass transport phenomena, which further impact their functionalities and durability. Reactive porous paint materials are composites in nature and widely used in arts and technological applications. In artistic oil paintings, ambient moisture and water and organic solvents used in conservation treatments are known to trigger multiple physical and chemical degradation processes; however, there is no complete physical model that can quantitatively describe their transport in the paint films. In the present study, model oil paints with lead white (2PbCO 3 ·Pb(OH) 2 ) and zinc white (ZnO) pigments, which are frequently found in artistic oil paintings and are associated with the widespread heavy metal soap deterioration, were studied using synchrotron X-ray nano-tomography and unilateral nuclear magnetic resonance. This study aims to establish a relationship among the paints’ compositions, the 3D morphological properties and degradation. This connection is crucial for establishing reliable models that can predict transport properties of solvents used in conservation treatments and of species involved in deterioration reactions, such as soap formation.

36 MATERIALS SCIENCE↗

DOE OSTI2020

In-situ X-ray scattering study of isotactic polypropylene/graphene nanocomposites under shear during fused deposition modeling 3D printing

Complementary techniques were applied to characterize the structure property relationships of FDM printed isotactic polypropylene/graphene nanocomposites. Raman spectroscopy indicated that graphene was mostly exfoliated during the nozzle extrusion process. Rheological measurements of the viscosity indicated that the presence of graphene induced shear thinning during extrusion. Azimuthal scans of wide angle x-ray scattering indicate correlated thermal fluctuations of the graphene platelets which stops abruptly at the onset of transcrystallization, or templating of the iPP chains on the graphene. X-ray microbeam SAXS analysis show the formation of ‘shish-kebab’ structures at the core of the unfilled filaments, where the ‘kebab’ component vanishes at the fiber-fiber interface enabling interdiffusion. Weak lamellar structure, and a corresponding decrease in the storage modulus are observed with the addition of 5% graphene. The lamellar structure disappears entirely with the addition of 10% graphene, while the storage modulus is decreased by nearly 50%. Thermal imaging of heat flux dissipation across molded and printed samples shows no orientational effects in pure iPP despite differences in crystal structure. Thermal conductivity increases dramatically in the samples with 10% graphene, and strong orientational effects are observed where the thermal coefficients differ by 180% between samples printed parallel or perpendicular to the heat flux.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Unveiling 3D Morphology of Multiscale Micro-Nanosilver Sintering for Advanced Electronics Manufacturing by Ptychographic X-ray Nanotomography

The sintering processing–structure–property relationship of a multiscale silver materials is investigated: microparticles with nanofeatures, particularly on their three-dimensional (3D) morphology. The target application is to replace conventional lead-based solders in advanced electronic manufacturing. Unlike lead-based solders, silver powders are suited to satisfy increasingly demanding mechanical, electrical, and thermal requirements, meanwhile being free of health effect. Sintering the material at a low temperature and without applied pressure are desirable conditions, which results in a preferred use of silver nanoparticles, as nanofeatures have higher driving force to sinter with the decrease in particle size. However, nanosized powders present potential health/environmental effects. To address the trade-off between the benefits and shortcomings of nano-versus microparticles, this work studies a novel multiscale silver paste, namely micron-sized powders with nanosized features. To get quantitative 3D visualization of micro- and nanoscale features, ptychographic X-ray computed nanotomography is applied. The correlations between conditions (thermal aging, pressure, and substrate metallization), mechanical properties, and morphological parameters are established. Finally, using novel 3D X-ray nanoimaging technique, it is demonstrated that one can design multiscale materials while balancing complex demands required in advanced electronics manufacturing and research directions in materials design and characterization.

36 MATERIALS SCIENCE↗