Search NASA⌕ Search

Engineering topics

Lind, Jonathan

Publications and source records attributed to Lind, Jonathan.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Quantifying motion blur by imaging shock front propagation with broadband and narrowband X-ray sources

Time-integrated radiography using MeV Bremsstrahlung X-ray sources is the norm for imaging during system-level testing of components and structures under dynamic condition. One source of error in the analysis of the time-integrated radiography data sets stems from motion blur which smears out sharp interfaces to a greater degree with longer exposure times, which become necessary to provide sufficient signal-to-noise with low X-ray penetration of objects of interest. To quantify motion blur, a 1D shock wave through PMMA was investigated experimentally at The Dynamic Compression Sector at The Advanced Photon Source (DCS@APS) with tapered broadband and 25.46 ± 1.06 keV narrowband X-rays. Four cameras with different exposure times were used for each experiment to compare the effect that exposure time has on motion blur. In addition, our methodology to accurately simulate motion blur in terms of transmission and shape is presented and compared to our experimental results and quantified. There is a high level of agreement between the experimental and simulation results across the range of data sets investigated in this study with a percent difference range of 0.29–1.31% for the four shots. The methodology of this work serves as a steppingstone towards a physically validated model that could be used in conjunction with experimental results to deconvolve physical parameters, densities, and interfaces of interest in a way that would not be possible with experimental results alone.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Solid face sheets enable lattice metamaterials to withstand high-amplitude impulsive loading without yielding

Owing to their ability to provide tunable mechanical responses, lattice materials are frequently studied to elucidate their response to static and dynamic loads. However, these roles are typically in opposition: static loads must be supported sufficiently far away from the onset of buckling or yielding, whereas dynamic loads are typically ameliorated by crushing of the lattice, which provides excellent energy-absorption due to the large plastic deformation accompanying densification. In contrast, this work considers the octet truss as an exemplar topology, in a structural role where it must simultaneously support static loads while enduring high-amplitude impulsive loads. This study focuses on the ability to withstand impulsive loads without yielding, an essential prerequisite to enduring dual loading. Computational studies using the ALE3D hydrocode were performed to examine the response of the octet truss under a short temporal width impulse shape associated with laser-driven shocks. A key finding was that covering the lattice with a solid face sheet and treating this face sheet thickness as a design variable allows the Taylor-like pulse to be attenuated prior to entering the weaker lattice, at the cost of added mass up front. Experimental validation was accomplished by laser-driven shock testing, using octet trusses printed out of Ti-5Al-5V-5Mo-3Cr. The results show that for a given quantity of mass, the attenuation is maximized when as much mass as possible is moved into the face sheet, leaving a more slender lattice structure. The effect of placing mass in the face sheet rather than lattice beams dominates the effect of relative density, to the point where a low-mass structure with most of the mass concentrated in the face sheet can outperform a high-mass structure with most of the mass in the lattice. Finally, by further understanding the propagation of short pulse width waves within under-dense structures, this study expand the domain of applicability of such structures, including lattice materials, to challenging dual-loading regimes spanning decades of strain rates.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Crystal plasticity model of BCC metals from large-scale MD simulations

Accurate crystal plasticity models that faithfully capture the behavior of single crystals under a wide range of loading conditions, such as loading direction, strain rate, and temperature, are still lacking. Here we introduce a novel approach in which a crystal plasticity (CP) model is informed directly from and calibrated to large-scale quantum-accurate MD simulations in which single crystal BCC Ta serves as a testbed material. By analyzing our large set of MD simulations several key insights are obtained leading us to modify constitutive assumptions in order to address deficiencies of existing CP models. Importantly, we observe that the standard notion of fixed slip systems – pairs of slip directions and slip planes – is inadequate for describing high-rate plasticity in BCC tantalum at room temperature. Instead, pencil glide defined as dislocation motion in the maximum resolved shear stress planes (MRSSP) of each Burgers vector is fully consistent with our MD simulation data while providing significant simplifications of the constitutive relations. Herein, our resulting new CP model closely matches the behavior of single crystals observed in high-rate MD simulations while being fully consistent with lower rate experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2022

X-ray diffraction from shock driven Sn microjets

Here, in situ x-ray diffraction was performed on shock-generated microjets composed of Sn and Sn–4Ag. Under low pressure drives (~21 GPa), a significant fraction of the jet volume was found to be in the β-Sn phase, and these crystallites were much smaller than the initial grain size of the material. Significant quantities of amorphous (molten) material were observed for higher drive pressures (~25–35 GPa). The extent of melting at these pressures was greater than would be predicted for uniaxial shock loading. Diffraction patterns from the Sn–4Ag alloy showed a peak that is consistent with the expected Ag 3 Sn intermetallic phase. This peak remained evident under drive conditions where the sample was otherwise fully amorphous. This indicates a slushy or a mixed phase of liquid Sn and solid Ag 3 Sn. Given the eutectic character of this alloy, this observation is attributed to a kinetic limitation on the dissolution of Ag 3 Sn. This implies that a much broader range of drive conditions will lead to mixed phase jets and ejecta than would be predicted from the equilibrium melt boundary of such alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-rate strength response of tantalum from dynamic hole closure experiments

The science and engineering communities have significant interest in experimental platforms to evaluate and improve models for dynamic material deformation. While well-developed platforms exist, there are still gaps to fill for strain and strain rate conditions accessed during impact and other high-rate loading scenarios. To fill one such gap for strength measurements, a platform was recently developed that accesses high strain rate (≥ 10 5 /s) and large strain (≥ 50%) conditions by measuring the transient closure of a cylindrical hole using in situ x-ray imaging. In the work reported here, further refinement of the platform is performed to reduce the potential effects of porosity and anelasticity on the measurement. This helps us to isolate the strength effects that are the focus of the experiment. The updated experimental configuration employs a two-layer flyer design and elongated target to reduce the magnitude of the tensile excursions associated with rarefaction wave interactions. This allows for a more direct assessment of strength models commonly used for dynamic simulations of metals. Here we apply the new technique to well-characterized tantalum material, allowing for a robust connection to other experimental techniques. Deformation localization can be a concern in large strain experiments, and to help inform future use of the experimental platform, we use simulations with a sub-zone treatment of shear banding to explore potential localization behavior. Here we develop and utilize an experimental configuration with improved isolation of strength effects that can be applied to an expanded range of materials.

42 ENGINEERING↗
DOE OSTI2021

Understanding the phase transformation mechanisms that affect the dynamic response of Fe-based microstructures at the atomic scales

Large-scale molecular dynamics (MD) simulations were carried out to investigate the shock-induced evolution of microstructure in Fe-based systems comprising single-crystal and layered Cu/Fe alloys with a distribution of interfaces. The shock compression of pure single-crystal Fe oriented along [110] above a threshold pressure results in a BCC (α)→HCP (ε) phase transformation behavior that generates a distribution of ε phase variants in the phase transformed region of the microstructure behind the shock front. The propagation of the release wave through a phase transformed ε phase causes a reverse ε→α phase transformation and renders a distribution of twins for the [110] oriented Fe that serve as void nucleation sites during spall failure. The simulations reveal that the α→ε→α transformation-induced twinning for shock loading along the [110] direction is due to a dominant ε phase variant formed during compression that rotates on the arrival of the release wave followed by a reverse phase transformation to twins in the α phase. The modifications in the evolution of the ε phase variants and twins in Fe behavior are also studied for Cu–Fe layered microstructures due to the shock wave interactions with the Cu/Fe interfaces using a newly constructed Cu–Fe alloy potential. Here, the MD simulations suggest that interfaces affect the observed variants during shock compression and, hence, distributions of twins during shock release that affects the void nucleation stresses in the Fe phase of Cu/Fe microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Grain boundary velocity and curvature are not correlated in Ni polycrystals

Grain boundary velocity has been believed to be correlated to curvature, and this is an important relationship for modeling how polycrystalline materials coarsen during annealing. We determined the velocities and curvatures of approximately 52,000 grain boundaries in a nickel polycrystal using three-dimensional orientation maps measured by high-energy diffraction microscopy before and after annealing at 800°C. Unexpectedly, the grain boundary velocities and curvatures were uncorrelated. Instead, we found strong correlations between the boundary velocity and the five macroscopic parameters that specify grain boundary crystallography. The sensitivity of the velocity to grain boundary crystallography might be the result of defect-mediated grain boundary migration or the anisotropy of the grain boundary energy. The absence of a correlation between velocity and curvature likely results from the constraints imposed by the grain boundary network and implies the need for a new model for grain boundary migration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Jetting Response in Architected Structures

Architected structures are gaining prominence for structural applications as the additive manufacturing technologies that can enable such materials mature. With the expanded design space, such mesoscopic structures occupy the middle ground between random foams and bulk materials. Studies into the deformation response of such structures are limited, particularly under dynamic compression. Early studies indicate the presence of an elastic precursor wave running ahead of the compaction wave. Additional studies also have shown that jetting is known to occur under shock loading conditions due to the presence of geometric perturbations introduced in the long-range periodic structures. Given that starting point, the motivation for this research was to understand the origin of the observed jetting and extend our understanding of how this comes about across a broad spectrum of lattice types, material compositions, length scales, and dynamic loading conditions. The jetting behavior due to lattice structures was studied through a series of dynamic compression plate impact experiments with in-situ x-ray imaging. This work was enabled by the NNSA-funded Dynamic Compression Sector at the Advanced Photon Source, which is housed at Argonne National Laboratory. Prior studies, and also evident in this work, have shown that deformation mechanisms in architected structures are difficult to study using our traditional diagnostics, and the role of in situ observations in this regard cannot be overstated. The role of the impact conditions, the lattice spacing, the lattice architecture, and the lattice base material was explored in the context of promoting or suppressing jet formation. A transition from latticeled to impactor-led jetting is observed above a certain impact threshold. Complementary direct numerical simulations (DNS) were also performed to compare with the experiments, study the underlying stress state giving rise to jetting, and provide insight for conditions not studied experimentally. Such simulations suggest certain trends for promoting or suppressing jetting akin to traditional Richtmyer-Meshkov instability studies. We present a geometric argument to explain the competitive process leading to lattice and/or impactor jetting which incorporates base material properties, the periodicity of the lattice, and basic tunable length scales of the lattice. Our results are consistent with previous observations on such lattices. Expanding on that work, the emergence of a transition of the jet material composition must depends solely on the base material properties and the geometric arrangement of the lattice structure. The fact that we have obtained reasonable qualitative and quantitative agreement regarding the jet formation and propagation behavior leads us to trust the underlying materials models. We can speculate that this and potentially other emergent phenomena might also be possible from a unique combination of base material properties and geometric arrangement of lattice structures. While the transition from polymer-led to flyer-led jetting might seem counterintuitive at first, it is a natural extension of the impact conditions and the arrangement of the materials. Better understanding of how the base material properties are coupled to the lattice structure to give rise to such phenomena will likely improve design for such structures under dynamic compression conditions. As such, the direct numerical simulations provide a pathway to design of architectures in future applications.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Application of Al-Cu-W-Ta graded density impactors in dynamic ramp compression experiments

Graded density impactors (GDIs) are utilized to dynamically compress materials to extreme conditions. Two modifications to a previously developed Mg-Cu-W GDI are made in this work before using it in a dynamic compression experiment: Mg is replaced with Al and a Ta disk is glued to the back. The Mg phase is replaced by Al because FCC Al remains solid to higher pressure along its Hugoniot compared to Mg. The addition of the Ta disk creates a constant particle velocity regime and facilitates a definition of peak pressure states. Microstructure analysis, profilometry, and ultrasonic C-scans of the Al-Cu-W GDI all confirm excellent uniformity. We evaluated signal variation in the radial direction of a dynamically compressed Al-LiF bilayer target to evaluate the contribution of spatial nonuniformity to errors. Velocity traces from five photon Doppler velocimetry (PDV) probes located at different radial distances from the center of the target varied at most by 1.1% with a root mean square of 0.3% during the compression ramp, demonstrating low PDV measurement error over a relatively large experimental area. The experimental PDV data additionally agrees well with 1D simulations that use inputs from predictive characterization models developed for the material properties resulting from tape casting, laminating, and powder consolidation processes. Low measurement error during quasi-isentropic compression, leading to better precision, promises a robust platform to reach extreme compression and low-temperature recovery states and facilitates discovery via synthesis, quenching, and preservation of new high-pressure phases.

36 MATERIALS SCIENCE↗
DOE OSTI2017

The formation and characterization of large twin related domains

The enhanced properties of grain boundary engineered metals are a result of their unique microstructures, which contain large clusters of twinned grains, called twin related domains. These large twin related domains in grain boundary engineered Ni were found to form through recrystallization. Orientation mapping showed that sparse nucleation and multiple twinning resulted in twin related domains containing hundreds of grains connected together in complex morphologies. A correlation was found between the size of the twin related domains and the overall twin boundary fraction. The same correlation was also observed in Cu and a Ni superalloy, showing that this is a general observation for grain boundary engineered microstructures. This finding can be understood through the topology of the twin related domains and an accompanying scaling relation is provided. The crystal orientations contained within each twin related domain were observed to depend on both the spatial correlation of twinning variants and the degree of branching in the twin boundary network. The results suggest a natural way of quantifying grain boundary engineered microstructures and provide a step toward making a closer connection between processing, microstructure, and performance.

36 MATERIALS SCIENCE↗