Search NASA⌕ Search

Engineering topics

Ling, F. F.

Publications and source records attributed to Ling, F. F..

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Tribological characteristics of a composite total-surface hip replacement

Continuous fiber, woven E glass composite femoral shells having the same elastic properties as bone were fabricated. The shells were then encrusted with filled epoxy wear resistant coatings and run dry against ultrahigh molecular weight polyethylene acetabular cups in 42,000 and 250,000 cycle wear tests on a total hip simulator. The tribological characteristics of these continuous fiber particulate composite femoral shells articulating with ultrahigh molecular weight polyethylene acetabular cups were comparable to those of a vitallium ball articulating with an ultrahigh molecular weight polyethylene acetabular cup.

Jones, W. R., Jr.↗
NASA NTRS1981

Fabrication and wear test of a continuous fiber/particulate composite total surface hip replacement

Continuous fiber woven E-glass composite femoral shells having the ame elastic properties as bone were fabricated. The shells were then encrusted with filled epoxy wear resistant coatings and run dry against ultrahigh molecular weight polyethylene acetabular cups in 42,000 and 250,000 cycle were tests on a total hip simulator. The tribological characteristics of these shells atriculating with the acetabular cups are comparable to a vitallium bal articulating with an ultrahigh molecular weight polyethylene cup.

Roberts, J. C.↗
NASA NTRS1976

Effect of design factors on surface temperature and wear in disk brakes

The temperatures, friction, wear and contact conditions that occur in high energy disk brakes are studied. Surface and near surface temperatures were monitored at various locations in a caliper disk brake during drag type testing, with friction coefficient and wear rates also being determined. The recorded transient temperature distributions in the friction pads and infrared photographs of the rotor disk surface both showed that contact at the friction surface was not uniform, with contact areas constantly shifting due to nonuniform thermal expansion and wear. The effect of external cooling and of design modifications on friction, wear and temperatures was also investigated. It was found that significant decreases in surface temperature and in wear rate can be achieved without a reduction in friction either by slotting the contacting face of the brake pad or by modifying the design of the pad support to improve pad compliance. Both design changes result in more uniform contact conditions on the friction surface.

Santini, J. J.↗
NASA NTRS1974

Effect of frictional heating on brake materials

An exploratory study of the properties of aircraft brake materials was made to determine ways of improving friction and wear behavior while minimizing surface temperatures. It is found that frictional variation at high temperature involves material softening and metal transfer, formation of oxides, and surface melting. The choice of proper materials to combat these effects is discussed. Minimum surface temperatures are found to result from use of materials with large density-specific heat and density-specific heat-conductivity factors, use of a higher load-lower friction system, and maximization of the contact area. Some useful trade-off criteria for the size of brake disks against weight considerations are suggested. Additional information on material behavior and peak braking temperatures was gathered from an inspection of used brake pads and rotor disks.

Ho, T.-L.↗
NASA NTRS1974

Elastodynamic response of hollow balls

Review of the underlying fundamentals, the performance procedure, and the results of an elastodynamic stress and deformation analysis of hollow balls aimed at providing a clear definition of parametric influences for the development of hollow ball bearing technology. A simplified model is used as a first approximation, and contact stress distributions are obtained with the aid of computer programming and processing.

Ling, F. F.↗
NASA NTRS1974

A thermal, thermoelastic, and wear analysis of high-energy disk brakes

A thermomechanical investigation of the sliding contact problem encountered in high-energy disk brakes is described. The analysis includes a modelling, using the finite element method of the thermoelastic instabilities that cause transient changes in contact area to occur on the friction surface. In order to include the effect of wear at the contact surface, a wear criterion is proposed that results in the prediction of wear rates for disk brakes that are quite close to experimentally determined wear rates. The thermal analysis shows that the transient temperature distribution in a disk brake assembly can be determined more accurately by use of this thermomechanical analysis than by a more conventional analysis that assumes constant contact conditions. It also shows that lower, more desirable, temperatures in disk brakes can be attained by increasing the volume, the thermal conductivity, and, especially, the heat capacity of the brake components.

Kennedy, F. E., Jr.↗
NASA NTRS1973

A thermal, thermoelastic, and wear simulation of a high-energy sliding contact problem

This paper describes an investigation of the sliding contact problem encountered in high-energy disk brakes. The analysis includes a simulation modeling, using the finite element method, of the thermoelastic instabilities that cause transient changes in contact to occur on the friction surface. In order to include the effect of wear of the concentrated contacts on the friction surface, a wear criterion is proposed that results in prediction of wear rates for disk brakes that are quite close to experimentally determined wear rates. The thermal analysis shows that the transient temperature distribution in a disk brake can be determined more accurately by use of this thermomechanical analysis than by a more conventional analysis that assumes constant contact conditions. It is also shown that lower, more desirable, temperatures in disk brakes can be attained by increasing the volume, the thermal conductivity, and especially, the heat capacity of the brake components.

Kennedy, F. E., Jr.↗