Search NASA⌕ Search

Engineering topics

Liu, Ao

Publications and source records attributed to Liu, Ao.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A thermotropic liquid crystal enables efficient and stable perovskite solar modules

Perovskite solar cells have seen impressive progress in performance and stability, yet maintaining efficiency while scaling area remains a challenge. Here we find that additives commonly used to passivate large-area perovskite films often co-precipitate during perovskite crystallization and aggregate at interfaces, contributing to defects and to spatial inhomogeneity. Here we develop design criteria for additives to prevent their evaporative precipitation and enable uniform passivation of defects. We explored liquid crystals with melting point below the perovskite processing temperature, functionalization for defect passivation and hydrophobicity to improve device stability. We find that thermotropic liquid crystals such as 3,4,5-trifluoro-4'-(trans-4-propylcyclohexyl)biphenyl enable large-area perovskite films that are uniform, low in defects and stable against environmental stress factors. We demonstrate modules with a certified stabilized efficiency of 21.1% at an aperture area of 31 cm 2 and enhanced stability under damp-heat conditions (ISOS-D-3, 85% relative humidity, 85 °C) with T 86 (the duration for the efficiency to decay to 86% of the initial value) of 1,200 h, and reverse bias with (ISOS-V-1, negative maximum-power-point voltage) and without bypass diodes.

14 SOLAR ENERGY↗
DOE OSTI2023

Pion-Production Target for Mu2e-II: Design and Prototype

The higher beam intensity available for Mu2e-II will require a substantially different target design. This paper discusses our recent advances in conceptual R&D for a Mu2e-II target station. The design is based on energy deposition and radiation damage simulations as well as thermal and mechanical analyses to estimate the survivability of the system. We considered rotated targets, fixed granular targets and a novel conveyor target with tungsten or carbon spherical elements that are circulated through the beam path. The motion of the spheres can be generated either mechanically or both mechanically and by a He-gas flow. The simulations identified the conveyor target as the preferred approach, and that approach has been developed into a prototype. We describe this first prototype for the Mu2e-II target and report on its mechanical tests performed at Fermilab that indicate the feasibility of the design, discuss its challenges as well as suggest directions for further improvement.

Neuffer, David↗
DOE OSTI2022

Cesium intercalation of graphene: A 2D protective layer on alkali antimonide photocathode

Alkali antimonide photocathodes have wide applications in free-electron lasers and electron cooling. The short lifetime of alkali antimonide photocathodes necessitates frequent replacement of the photocathodes during a beam operation. Furthermore, exposure to mediocre vacuum causes loss of photocathode quantum efficiency due to the chemical reaction with residual gas molecules. Theoretical analyses have shown that covering an alkali antimonide photocathode with a monolayer graphene or hexagonal boron nitride protects it in a coarse vacuum environment due to the inhibition of chemical reactions with residual gas molecules. Alkali antimonide photocathodes require an ultra-high vacuum environment, and depositing a monolayer 2D material on it poses a serious challenge. In the present work, we have incorporated a novel method known as intercalation, in which alkali atoms pass through the defects of a graphene thin film to create a photocathode material underneath. Initially, Sb was deposited on a Si substrate, and a monolayer graphene was transferred on top of the Sb film. Heat cleaning around 550–600 °C effectively removed the Sb oxides, leaving metallic Sb underneath the graphene layer. Depositing Cs on top of a monolayer graphene enabled the intercalation process. Atomic force microscopy, Raman spectroscopy, x-ray photoelectron spectroscopy, low energy electron microscopy, and x-ray diffraction measurements were performed to evaluate photocathode formation underneath the monolayer graphene. Our analysis shows that Cs penetrated the graphene and reacted with Sb and formed Cs 3 Sb.

2D materials↗
DOE OSTI2022

Preliminary Results from ADRIANO2 Test Beams

A novel high-granularity, dual-readout calorimetric technique (ADRIANO2) is under development as part of the research program of T1604 Collaboration. (Talk Presented at the 19th International Conference on Calorimetry in Particle Physics (CALOR 2022), University of Sussex, Sussex, UK, 16–20 May 2022). The building block of such a calorimeter consists of a pair of optically isolated, small size tiles made of scintillating plastic and lead glass. The prompt Čerenkov light from the glass can be exploited to perform high resolution timing measurements, while the high granularity provides good resolution of the spatial components of the shower. Dual-readout compensation and particle flow techniques can be applied simultaneously to the scintillation and to the Čerenkov section, providing excellent energy resolution as well as PID particle identification. These characteristics make ADRIANO2 a 6-D detector, suited for High Energy as well as High Intensity experiments. A report on the status of the ADRIANO2 project, preliminary measurements of light yield, and current and future R&D plans by T1604 Collaboration are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗