Search NASA⌕ Search

Engineering topics

Liu, Cong

Publications and source records attributed to Liu, Cong.

At least 55 records · Page 3

Droplet Evaporation on Hot Micro-Structured Superhydrophobic Surfaces: Analysis of Evaporation from Droplet Cap and Base Surfaces

In this study, evaporation of sessile water droplets on hot micro-structured superhydrophobic surfaces is experimentally and theoretically investigated. Water droplets of 4 µL are placed on micro-pillared silicon substrates with the substrate temperature heated up to 120°C. A comprehensive thermal circuit model is developed to analyze the effects of substrate roughness and substrate temperature on the sessile droplet evaporation. For the first time, two components of heat and mass transfer, i.e., one from the droplet cap surface and the other from the droplet base surface, during droplet evaporation are distinguished and systematically studied. As such, the evaporation heat transfer rates from both the droplet cap surface and the interstitial liquid-vapor interface between micropillars at the droplet base are calculated in various conditions. For droplet evaporation on the heated substrates in the range of 40°C – 80°C, the predicted droplet cap temperature matches well with the experimental results. Furthermore, during the constant contact radius mode of droplet evaporation, the decrease of evaporation rate from the droplet base contributes most to the continuously decreasing overall evaporation heat transfer rate, whereas the decrease of evaporation rate from the droplet cap surface is dominant in the constant contact angle mode. The influence of internal fluid flow is considered for droplet evaporation on substrates heated above 100°C, and an effective thermal conductivity is adopted as a correction factor to account for the effect of convection heat transfer inside the droplet. Temperature differences between the droplet base and the substrate base are estimated to be about 2°C, 5°C, 8°C, 13°C and 18°C for droplet evaporation on substrates heated at 40°C, 60°C, 80°C, 100°C, and 120°C, respectively, elucidating the delayed or depressed boiling of water droplets on a heated rough surface due to evaporative cooling.

42 ENGINEERING↗

Single-Molecule Kinetics of Styrene Hydrogenation on Silica-Supported Vanadium: The Role of Disorder for Single-Atom Catalysts

We report a theoretical approach for the study of supported atom catalysis is developed based on recent advances in the study of single-molecule kinetics. This view is particularly useful in exhibiting the role of disorder in single-atom and single-site catalysts on amorphous supports. The distribution of passage times (or waiting times) through a complex catalytic network originating from a set of coupled active sites is described by a probability distribution function (PDF), f(t), that reflects the local environment of the reaction center. An efficient algorithm is developed based on the linear algebra of the Markov transition matrix that produces f(t) or its moments. The kinetics of the hydrogenation reaction of styrene on an organovanadium(III) catalyst supported on amorphous silica is studied. A kinetic model consisting of three intertwined catalytic cycles emanating from three chemically distinct active sites is proposed to describe the chemistry. Density functional theory (DFT) calculations are employed to determine the free energy barriers of the reactions, which are used to construct the rate coefficient matrix. The disorder induced by the amorphous support material is divided into a low-dimensional short-range component reflecting the covalent structures near the reaction center and a weaker long-range component modeling the bulk randomness. The results are computed and analyzed for a wide range of concentration values and disorder scenarios. The unusual structure in the f(t) PDF is found to occur for certain cases that reveal the contribution of multiple catalytic pathways acting in concert.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Computational Investigation of the Role of Active Site Heterogeneity for aSupported Organovanadium(III) Hydrogenation Catalyst

A crucial consideration for supported heterogeneous catalysts is the nonuniformity of the active sites, particularly for supported organometallic catalysts. Standard spectroscopic techniques, such as X-ray absorption spectroscopy, reflect the nature of the most populated sites, which are often intrinsically structurally distinct from the most active catalytic sites. Additionally, with computational models, often, only a few representative structures are used to depict catalytic active sites on a surface, even though there are numerous observable factors of surface heterogeneity that contribute to the kinetically favorable active species. A previously reported study on the mechanism of a surface organovanadium-(III) catalyst [(SiO 2 )V III (Mes)(THF)] for styrene hydrogenation yielded two possible mechanisms: heterolytic cleavage and redox cycling. These two mechanistic scenarios are challenging to differentiate experimentally since the kinetic readouts of the catalyst are identical. To showcase the importance of modeling surface heterogeneity and its effect on catalytic activity, density functional theory (DFT) computational models of a series of potential active sites of [(SiO 2 )V III (Mes)(THF)] for the reaction pathways are applied in combination with kinetic Monte Carlo (kMC) simulations. Computed results were then compared to the previously reported experimental kinetic study: (1) DFT free-energy reaction pathways indicated the likely active site and pathway for styrene hydrogenation, a heterolytic cleavage pathway requiring a bare tripodal vanadium site. (2) From the kMC simulations, a mixture of different bond lengths from the support oxygen to the metal center was required to qualitatively describe the experimentally observed kinetic aspects of a supported organovanadium(III) catalyst for olefin hydrogenation. This work underscores the importance of modeling surface heterogeneity in computational catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal Atomic Layer Deposition of Gold: Mechanistic Insights, Nucleation, and Epitaxy

An in situ microbalance and infrared spectroscopic study of alternating exposures to Me2Au(S2CNEt2) and ozone illuminates the organometallic chemistry that allows for the thermal atomic layer deposition (ALD) of gold. In situ quartz crystal microbalance (QCM) studies resolve the nucleation delay and island growth of Au on a freshly prepared aluminum oxide surface with single cycle resolution, revealing inhibition for 40 cycles prior to slow nucleation and film coalescence that extends over 300 cycles. In situ infrared spectroscopy informed by first-principles computation provides insight into the surface chemistry of the self-limiting half-reactions, which are consistent with an oxidized Au surface mechanism. X-ray diffraction of ALD-grown gold on silicon, silica, sapphire, and mica reveals consistent out-of-plane oriented crystalline film growth as well as epitaxially directed in-plane orientation on closely lattice-matched mica at a relatively low growth temperature of 180 degrees C. A more complete understanding of ALD gold nucleation, surface chemistry, and epitaxy will inform the next generation of low-temperature, nanoscale, textured depositions that are applicable to high surface area supports.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrochemical Investigation of Low-Valent Multiply M≡M Bonded Group VI Dimers: A Standard Chemical Reduction Leads to an Unexpected Product

The synthesis and investigation of multimetallic complexes bearing metal–metal bonds have been significantly advanced over the last 30 years with exciting applications across many fields. While the outlook for synthetically innovative metal–metal species is promising, the reactivity of the classic M 2 X 6 alkyl dimers (where M = W, Mo; X = CH 2 CMe 3 , CH 2 SiMe 3 ) is still not fully understood. In particular, the redox characteristics of these complexes have not been explored by cyclic voltammetry (CV). In this work, W 2 (CH 2 CMe 3 ) 6 and Mo 2 (CH 2 CMe 3 ) 6 (1 and 2, respectively) were characterized using CV to show differing electrochemical behavior between the two species. Stoichiometric reactions, guided by the results of the CV experiments, led to the isolation of an alkylidyne-bridged dimer bearing a rare structural motif, W 2 (μ-CCMe 3 ) 2 (CH 2 CMe 3 ) 4 (3). Single-crystal X-ray diffraction (SCXRD) and 1 H and 13 C nuclear magnetic resonance spectroscopy (NMR) were used to establish the connectivity of the structure in the solid and solution phases. Density functional theory (DFT) calculations on 1–3 and the previously reported W 2 (CSiMe 3 ) 2 (CH 2 SiMe 3 ) 4 (4) were used to rationalize the reactivity of 1 to form 3 and the structural differences between 3 and 4. Complexes 3 and 4 constitute a case in which the stereoelectronic properties of the silyl neopentyl ligand can affect differences in structure and bonding.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Cation Additive Enabled Rechargeable LiOH‐Based Lithium–Oxygen Batteries

Abstract Lithium–oxygen (Li–O 2 ) batteries have attracted extensive research interest due to their high energy density. Other than Li 2 O 2 (a typical discharge product in Li–O 2 batteries), LiOH has proved to be electrochemically active as an alternative product. Here we report a simple strategy to achieve a reversible LiOH‐based Li–O 2 battery by using a cation additive, sodium ions, to the lithium electrolyte. Without redox mediators in the cell, LiOH is detected as the sole discharge product and it charges at a low charge potential of 3.4 V. A solution‐based reaction route is proposed, showing that the competing solvation environment of the catalyst and Li + leads to LiOH precipitation at the cathode. It is critical to tune the cell chemistry of Li–O 2 batteries by designing a simple system to promote LiOH formation/decomposition.

Bi, Xuanxuan↗

Cation Additive Enabled Rechargeable LiOH-Based Lithium–Oxygen Batteries

Lithium-oxygen (Li-O 2 ) batteries have attracted extensive research interest due to their high energy density. Other than Li 2 O 2 (a typical discharge product in Li-O 2 batteries), LiOH has proved to be electrochemically active as an alternative product. Here we report a simple strategy to achieve a reversible LiOH-based Li-O 2 battery by using a cation additive, sodium ions, to the lithium electrolyte. Without redox mediators in the cell, LiOH is detected as the sole discharge product and it charges at a low charge potential of 3.4 V. A solution-based reaction route is proposed, showing that the competing solvation environment of the catalyst and Li+ leads to LiOH precipitation at the cathode. It is critical to tune the cell chemistry of Li-O 2 batteries by designing a simple system to promote LiOH formation/decomposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The electrolyte comprising more robust water and superhalides transforms Zn-metal anode reversibly and dendrite-free

A great challenge for all aqueous batteries, including Zn-metal batteries, is the parasitic hydrogen evolution reaction on the low-potential anode. Herein, we report the formula of a highly concentrated aqueous electrolyte that mitigates hydrogen evolution by transforming water molecules more inert. The electrolyte comprises primarily ZnCl 2 and LiCl as an additive, both of which are inexpensive salts. The O–H covalent bonds in water get strengthened in a chemical environment that has fewer hydrogen bonding interactions and a greater number of Zn–Cl superhalides, as suggested by integrated characterization and simulation. As a result, the average Coulombic efficiency of zinc-metal anode is raised to an unprecedented >99.7% at 1 mA cm –2 . In the new electrolyte, the plating/stripping processes leave the zinc-metal anode dendrite-free, and the zinc-metal anode delivers stable plating/stripping cycles for 4000 hours with an areal capacity of 4 mAh cm –2 at 2 mA cm –2 . Furthermore, the high Coulombic efficiency of zinc-metal anode in the ZnCl 2 -LiCl mixture electrolyte is demonstrated in full cells with a limited anode. The V 2 O 5 ·H 2 O| |Zn full cell with an N/P mass ratio of 1.2 delivers a stable life of more than 2500 cycles, and the LiMn 2 O 4 | |Zn hybrid cell with an N/P mass ratio of 0.6 exhibits 1500 cycles in its stable life.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly selective electrocatalytic CO 2 reduction to ethanol by metallic clusters dynamically formed from atomically dispersed copper

Direct electrochemical conversion of CO 2 to ethanol offers a promising strategy of lowering CO 2 emission while storing energy from renewable electricity. However, current electrocatalysts offer only limited selectivity toward ethanol. Here we report a copper catalyst synthesized by a unique Cu-Li amalgm method over a commercial carbon support that achieved Faradaic efficiency (FE) higher than 91% at -0.7 V (RHE) and the active potential as low as -0.4 V (RHE) during direct electrocatalytic CO 2 -to-ethanol conversion. The catalyst also demonstrated stability over an extended period of operation. A strong correlation between the catalytic selectivity and the initial Cu atoms dispersion was found and Operando X-ray absorption spectroscopy identified a dynamic and reversible transformation from atomically dispersed copper atoms to Cu n (n = 3 and 4) under the electrochemical reaction. Frist-principles calculations further elucidate the possible catalytic mechanism of CO 2 reduction over Cu n .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fluorinated co-solvent promises Li-S batteries under lean-electrolyte conditions

Practical lithium-sulfur batteries stipulate the use of a lean-electrolyte and a high Coulombic efficiency of the lithium metal anode. In this work, we employ 1,1,2,2-tetrafluoroethyl 2,2,2-trifluoroethyl ether as a co-solvent in the electrolyte of Li-S batteries to meet the demands. The co-solvent fosters the formation of a LiF-rich solid electrolyte interphase on lithium metal anode, as revealed by Ab initio molecular dynamics and Femtosecond Stimulated Raman spectroscopy. The co-solvent results in an average Coulombic efficiency of 99.4% for lithium plating/stripping cycles. Full cells with a capacity ratio of 2 between lithium anode and the S@PAN cathode (3 gs cm –2 ) exhibited a stable cycle life over 100 cycles at an electrolyte/sulfur ratio of 2 µL mg –1 , validating the high Coulombic efficiency of the lithium anode and demonstrating the compatibility of the electrolyte with both electrodes. To enhance the energy density, we prepared a hybrid cathode composed of 45 wt.% VS 2 mixed with ZnS-coated Li 2 S@graphene as the cathode. Based on the mass of both electrodes and the electrolyte, the full cell delivers an energy density of 483 Wh kg –1 , which demonstrates viable Li-S batteries with the lean-electrolyte.

25 ENERGY STORAGE↗

Role of Boron in Enhancing the Catalytic Performance of Supported Platinum Catalysts for the Nonoxidative Dehydrogenation of n -Butane

Platinum-based supported catalysts for hydrocarbon conversion are among the most effective for selective dehydrogenation and isomerization processes. However, high process temperatures and the possibility of coke formation require catalyst modifications to mitigate such effects. One of the emerging approaches to prevent platinum catalyst deactivation is the use of boron additives that have been proposed to prevent coking. Despite such a valuable property of boron, the mechanisms for extending the catalyst lifetime and the decrease in coke formation based on this method are still poorly understood. The type and transformations of boron species on silica surface were investigated as a function of boron introduction, platinum addition, catalyst activation, and catalytic reactivity by a combination of X-ray photoelectron spectroscopy, electron microscopy, solid-state nuclear magnetic resonance spectroscopy, and density functional theory calculations to uncover the possible role of boron modification in improving the catalytic performance. Catalytic nonoxidative dehydrogenation of n-butane revealed that incorporation of boron improved the catalytic activity (similar to 3x) and stability of Pt/SiO 2 . The role of boron in enhancing catalytic performance was attributed to facilitating the migration of alkyl groups from platinum catalytic centers to tetrahedrally coordinated boron sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Facet-dependent active sites of a single Cu 2 O particle photocatalyst for CO 2 reduction to methanol

Atomic level understanding of the active sites and transformation mechanisms under realistic working conditions are pre-requisites for rational design of high performance photocatalysts. By using correlated scanning fluorescence x-ray microscopy and environmental transmission electron microscopy at atmospheric pressure, in operando, we directly observed that the (110) facet of a single Cu 2 O photocatalyst particle is photocatalytically active for CO 2 reduction to methanol while the (100) facet is inert. The oxidation state of the active sites changed from Cu(I) towards Cu(II) due to CO 2 and H 2 O coadsorption and changed back to Cu+ after CO 2 conversion under visible light illumination. The Cu 2 O photocatalyst oxidized water as it reduced CO 2 . At the same time, the crystal lattice expanded due to CO 2 adsorption then reverted after CO 2 conversion. The internal quantum yield for unassisted wireless photocatalytic reduction of CO 2 to methanol using Cu 2 O crystals is ~ 72% with 10% solar to fuel efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mechanistic Aspects of a Surface Organovanadium(III) Catalyst for Hydrocarbon Hydrogenation and Dehydrogenation

Understanding the mechanisms of action for base metal catalysis of transformations typically associated with precious metals is essential for the design of technologies for a sustainable energy economy. Isolated transition-metal and post-transition-metal catalysts on oxides such as silica are generally proposed to effect hydrogenation and dehydrogenation by a mechanism featuring either σ-bond metathesis or heterolytic bond cleavage as the key bond activation step. In this work, an organovanadium(III) complex on silica, which is a precatalyst for both olefin hydrogenation and alkane dehydrogenation, is interrogated by a series of reaction kinetics and isotopic labeling studies in order to shed light on the operant mechanism for hydrogenation. The kinetic dependencies of the reaction components are potentially consistent with both the σ-bond metathesis and the heterolytic bond activation mechanisms; however, a key deuterium incorporation experiment definitively excludes the simple σ-bond metathesis mechanism. Alternatively, a two-electron redox cycle, rarely invoked for homologous catalyst systems, is also consistent with experimental observations. Evidence supporting the formation of a persistent vanadium(III) hydride upon hydrogen treatment of the as-prepared material is also presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗