Search NASA⌕ Search

Engineering topics

Liu, Fangyuan

Publications and source records attributed to Liu, Fangyuan.

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Amorphous Iridium Oxide-Integrated Anode Electrodes with Ultrahigh Material Utilization for Hydrogen Production at Industrial Current Densities

Herein, ionomer-free amorphous iridium oxide (IrO x ) thin electrodes are first developed as highly active anodes for proton exchange membrane electrolyzer cells (PEMECs) via low-cost, environmentally friendly, and easily scalable electrodeposition at room temperature. Combined with a Nafion 117 membrane, the IrO x -integrated electrode with an ultralow loading of 0.075 mg cm –2 delivers a high cell efficiency of about 90%, achieving more than 96% catalyst savings and 42-fold higher catalyst utilization compared to commercial catalyst-coated membrane (2 mg cm –2 ). Additionally, the IrO x electrode demonstrates superior performance, higher catalyst utilization and significantly simplified fabrication with easy scalability compared with the most previously reported anodes. Notably, the remarkable performance could be mainly due to the amorphous phase property, sufficient Ir 3+ content, and rich surface hydroxide groups in catalysts. Overall, due to the high activity, high cell efficiency, an economical, greatly simplified and easily scalable fabrication process, and ultrahigh material utilization, the IrO x electrode shows great potential to be applied in industry and accelerates the commercialization of PEMECs and renewable energy evolution.

08 HYDROGEN↗
DOE OSTI2023

Perovskite evolution on La modified Mn 1.5 Co 1.5 O 4 spinel through thermal ageing with enhanced oxidation activity: Is sintering always an issue?

Non-precious metal oxides have great potential in catalytic deep oxidation of emitted hydrocarbons to help address various environmental pollution concerns. However, sintering issue is a stumbling block in practical application upon long-term high-temperature operation or thermal shock experience. Herein, La was applied to modify Mn 1.5 Co 1.5 O 4 spinel to get a highly active oxidation catalyst with exceptional stability against high-temperature thermal ageing treatment. With thermal ageing at 750 °C for 100 h, the La modified Mn–Co composite reached 90 % conversion in toluene oxidation at 265 °C under the high WHSV of 120,000 mL g -1 h -1 , while this value increased to 312 °C over blank Mn–Co spinel. The addition of La not only inhibited the growth of spinel nanocrystals, but also brought about perovskite formation through sintering, generating perovskite-spinel interfaces, thus enhancing both activity and stability. Meanwhile, the La modified Mn–Co spinel exhibited superior performance in presence of water or sulfur dioxide after thermal ageing treatment. In conclusion, this work offers a versatile strategy to design anti-sintering and active oxidation nanocatalysts based on non-precious metal oxides for industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Unraveling Anisotropic and Pulsating Etching of ZnO Nanorods in Hydrochloric Acid via Correlative Electron Microscopy

Despite much technical progress achieved so far, the exact surface and shape evolution during wet chemical etching is less unraveled, especially in ionically bonded ceramics. Herein, by using in situ liquid cell transmission electron microscopy, a repeated two-stage anisotropic and pulsating periodic etching dynamic is discovered during the pencil shape evolution of a single crystal ZnO nanorod in aqueous hydrochloric acid. Specifically, the nanopencil tip shrinks at a slower rate along [0001̅] than that along the $\langle$101̅0$\rangle$ directions, resulting in a sharper ZnO pencil tip. Afterward, rapid tip dissolution happens due to accelerated etching rates along various crystal directions. Concurrently, the vicinal base region of the original nanopencil tip emerges as a new tip followed by the repeated sequence of tip shrinking and removal. The high-index surfaces, such as {101̅m} (m = 0, 1, 2, or 3) and {21̅1̅n} (n = 0, 1, 2, or 3), are found to preferentially expose in different ratios. Our 3D electron tomography, convergent beam electron diffraction, middle-angle bright-field STEM, and XPS results indicate the dissociative Cl – species were bound to the Zn-terminated tip surfaces. Furthermore, DFT calculation suggests the preferential Cl – passivation over the {101̅1} and (0001) surfaces of lower energy than others, leading to preferential surface exposures and the oscillatory variation of different facet etching rates. The boosted reactivity due to high-index nanoscale surface exposures is confirmed by comparatively enhanced chemical sensing and CO 2 hydrogenation activity. In conclusion, these findings provide an in-depth understanding of anisotropic wet chemical etching of ionic nanocrystals and offer a design strategy for advanced functional materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Optimization and understanding of ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst for enhanced CO 2 -methanol conversion at low temperature and pressure

Cu-ZnO-Al 2 O 3 is the most widely applied catalyst for CO 2 hydrogenation to methanol. However, it is still a challenge to produce methanol using this catalyst under low-temperature (<250 °C) and low-pressure (<10 bar) conditions with desirable yield and selectivity. In this work, by tuning the experimental processing parameters such as solvent, loading amount, and annealing temperature, highly improved ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalysts have been successfully demonstrated. Here, by using organic solvent (N,N-dimethylformamide (DMF), acetone, or isopropanol) for dip-coating loading process instead of deionized (DI) water, Cu-ZnO-Al 2 O 3 nanocatalysts was comparatively better dispersed on the nanorod array support with populated and abundant active sites, thus enhancing the methanol yield. With the control of the loading amount and annealing temperature, finely distributed Cu nanoparticles were obtained on the ZnO nanorod surfaces to enhance the interactions between Cu and ZnO nanorod surfaces. Further improvement of the catalyst performance is demonstrated by tuning the reaction space velocity. At 200 °C and 10 bar conditions, the optimized catalyst achieved a methanol yield of 6.46 mol h –1 kg –1 with 100 % selectivity. The good stability after prolonged testing of the catalysts demonstrates the potential practical implementation. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) measurements under the 1 bar reveal that the CO 2 hydrogenation to methanol on the ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst follows the CO reaction pathway, due to the surface oxygen vacancies on ZnO nanorods which facilitate CO 2 dissociation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Synergistic promotion of transition metal ion-exchange in TiO 2 nanoarray-based monolithic catalysts for the selective catalytic reduction of NO x with NH 3

TiO 2 supported catalysts have been widely studied for the selective catalytic reduction (SCR) of NO x ; however, comprehensive understanding of synergistic interactions in multi-component SCR catalysts is still lacking. For this work, transition metal elements (V, Cr, Mn, Fe, Co, Ni, Cu, La, and Ce) were loaded onto TiO 2 nanoarrays via ion-exchange using protonated titanate precursors. Amongst these catalysts, Mn-doped catalysts outperform the others with satisfactory NO conversion and N 2 selectivity. Cu co-doping into the Mn-based catalysts promotes their low-temperature activity by improving reducibility, enhancing surface Mn 4+ species and chemisorbed labile oxygen, and elevating the adsorption capacity of NH 3 and NO x species. While Ce co-doping with Mn prohibits the surface adsorption and formation of NH 3 and NO x derived species, it boosts the N 2 selectivity at high temperatures. By combining Cu and Ce as doping elements in the Mn-based catalysts, both the low-temperature activity and the high-temperature N 2 selectivity are enhanced, and the Langmuir–Hinshelwood reaction mechanism was proved to dominate in the trimetallic Cu–Ce–5Mn/TiO 2 catalysts due to the low energy barrier.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Transition-metal doped titanate nanowire photocatalysts boosted by selective ion-exchange induced defect engineering

Defect engineering through elemental doping is an efficient way to boost the performance of semiconductor photocatalysts. For this work, transition-metal (TM) doped titanate nanowires (TNWs) were prepared via ion-exchange over the titanate precursors and demonstrated for the Rhodamine B (RhB) degradation under ultraviolet (UV) light irradiation. The ion-exchange of selective ions (V 5+ , Cr 3+ , Ni 2+ , and Zn 2+ ) with protons from pristine TNWs resulted in the hierarchical meso-porosity of nanowires with large pores of ~5–20 nm by TM doping and small pores of ~3.6–4.5 nm inherited from pristine TNWs, which facilitates the mass transfer while maintaining high surface area and active sites. Meanwhile, the TM intercalation partially reduces the Ti 4+ to Ti 3+ and narrows the optical bandgap, which, together with oxygen vacancies and superoxide radicals from pristine TNWs, enhance the adsorption and photocatalytic degradation performance of RhB. This work helps to elucidate the effects of transition-metal doping and provides a rational strategy towards high performance titanate-based photocatalysts for efficient and sustainable wastewater treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Toward Long-Term Accurate and Continuous Monitoring of Nitrate in Wastewater Using Poly(tetrafluoroethylene) (PTFE)–Solid-State Ion-Selective Electrodes (S-ISEs)

Long-term accurate and continuous monitoring of nitrate (NO 3 – ) concentration in wastewater and groundwater is critical for determining treatment efficiency and tracking contaminant transport. Current nitrate monitoring technologies, including colorimetric, chromatographic, biometric, and electrochemical sensors, are not feasible for continuous monitoring. In this work, we addressed this challenge by modifying NO 3 – solid-state ion-selective electrodes (S-ISEs) with poly(tetrafluoroethylene) (PTFE, (C 2 F 4 ) n ). The PTFE-loaded S-ISE membrane polymer matrix reduces water layer formation between the membrane and electrode/solid contact, while paradoxically, the even more hydrophobic PTFE-loaded S-ISE membrane prevents bacterial attachment despite the opposite approach of hydrophilic modifications in other antifouling sensor designs. Specifically, an optimal ratio of 5% PTFE in the S-ISE polymer matrix was determined by a series of characterization tests in real wastewater. Five percent of PTFE alleviated biofouling to the sensor surface by enhancing the negative charge (–4.5 to –45.8 mV) and lowering surface roughness (Ra: 0.56 ± 0.02 nm). It simultaneously mitigated water layer formation between the membrane and electrode by increasing hydrophobicity (contact angle: 104°) and membrane adhesion and thus minimized the reading (mV) drift in the baseline sensitivity (“data drifting”). Long-term accuracy and durability of 5% PTFE-loaded NO 3 – S-ISEs were well demonstrated in real wastewater over 20 days, an improvement over commercial sensor longevity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗