Search NASA⌕ Search

Engineering topics

Liu, Ming

Publications and source records attributed to Liu, Ming.

At least 37 records · Page 2

Thermal Insulation for a High Temperature Molten Salt Storage Tank in a CSP Plant

A ternary molten chloride has been suggested as a high temperature (550-720 °C) sensible heat storage medium for a two-tank system. An effective thermal insulation is proposed to provide an opportunity for the fabrication of both the hot and cold storage tanks from lower cost metals, e.g. A240-347H, by maintaining the tank wall below 500 °C. To achieve this, the hot storage tank mainly comprises of inner shell (11.4 cm of a refractory brick as liner (KX-99®), 30 cm of insulation brick) and outer metal shell, where 5 cm of frozen layer of PCM800 (NaCl), and 5 cm of ceramic wool fill the annular space between the shells. Another layer of ceramic wool was introduced at the outer side of the metal shell to keep the temperature lower than 60 °C. ANSYS Fluent was used for the numerical study of the cool down behavior of the system during idle period when tank is quarter-filled. The heat transfer modes were considered as radiation and natural convection heat transfer from the hot molten salt at 720 °C, conduction through the solid layers and convection heat transfer from the outer shell to the environment at 15 °C. The results showed that the proposed insulation system including a frozen layer of PCM800 maintains the temperature at the metal wall lower than 500 °C, and lower than 60°C at the outer side of the tank. Apart from the insulation property of the frozen layer of PCM800, it absorbs any leak of hot molten salt, acting as a barrier between salt and the metal shell. The thermal performance analysis provide an insight into the benefits of the multilayer insulation.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Phase transition enhanced superior elasticity in freestanding single-crystalline multiferroic BiFeO 3 membranes

The integration of ferroic oxide thin films into advanced flexible electronics will bring multifunctionality beyond organic and metallic materials. However, it is challenging to achieve high flexibility in single-crystalline ferroic oxides that is considerable to organic or metallic materials. Here, we demonstrate the superior flexibility of freestanding single-crystalline BiFeO 3 membranes, which are typical multiferroic materials with multifunctionality. They can endure cyclic 180° folding and have good recoverability, with the maximum bending strain up to 5.42% during in situ bending under scanning electron microscopy, far beyond their bulk counterparts. Such superior elasticity mainly originates from reversible rhombohedral-tetragonal phase transition, as revealed by phase-field simulations. This study suggests a general fundamental mechanism for a variety of ferroic oxides to achieve high flexibility and to work as smart materials in flexible electronics.

36 MATERIALS SCIENCE↗

Naphthalene‐Diimide‐Based Ionenes as Universal Interlayers for Efficient Organic Solar Cells

Abstract Self‐doping ionene polymers were efficiently synthesized by reacting functional naphthalene diimide (NDI) with 1,3‐dibromopropane ( NDI‐NI ) or trans ‐1,4‐dibromo‐2‐butene ( NDI‐CI ) via quaternization polymerization. These NDI‐based ionene polymers are universal interlayers with random molecular orientation, boosting the efficiencies of fullerene‐based, non‐fullerene‐based, and ternary organic solar cells (OSCs) over a wide range of interlayer thicknesses, with a maximum efficiency of 16.9 %. NDI‐NI showed a higher interfacial dipole (Δ), conductivity, and electron mobility than NDI‐CI , affording solar cells with higher efficiencies. These polymers proved to efficiently lower the work function ( WF ) of air‐stable metals and optimize the contact between metal electrode and organic semiconductor, highlighting their power to overcome energy barriers of electron injection and extraction processes for efficient organic electronics.

Liu, Ming↗

Naphthalene‐Diimide‐Based Ionenes as Universal Interlayers for Efficient Organic Solar Cells

Abstract Self‐doping ionene polymers were efficiently synthesized by reacting functional naphthalene diimide (NDI) with 1,3‐dibromopropane ( NDI‐NI ) or trans ‐1,4‐dibromo‐2‐butene ( NDI‐CI ) via quaternization polymerization. These NDI‐based ionene polymers are universal interlayers with random molecular orientation, boosting the efficiencies of fullerene‐based, non‐fullerene‐based, and ternary organic solar cells (OSCs) over a wide range of interlayer thicknesses, with a maximum efficiency of 16.9 %. NDI‐NI showed a higher interfacial dipole (Δ), conductivity, and electron mobility than NDI‐CI , affording solar cells with higher efficiencies. These polymers proved to efficiently lower the work function ( WF ) of air‐stable metals and optimize the contact between metal electrode and organic semiconductor, highlighting their power to overcome energy barriers of electron injection and extraction processes for efficient organic electronics.

Liu, Ming↗

Role of Lithium Codoping in Enhancing the Scintillation Yield of Aluminate Garnets

The aim of this work is to clarify the scintillation-yield enhancement in Lu YAG : Pr scintillators obtained by Li codoping via integrated study of the valence state of activators, the preferential site occupancy of Li codopants, and defect structures from experimental and theoretical insights. Here, with Li codoping, the light yield and energy resolution of 10 × 10 × 10 mm 3 Lu YAG : Pr samples are improved from 156000 to 248000 photons/MeV, and 5.3 to 4.3% at 662 keV,respectively.The optical absorption spectra indicate that Li codoping does not induce conversion of stable Pr 3 + to Pr 4 + in Lu YAG : Pr single crystals. Based on the formation energies of substitutional and interstitial Li sites using density-functional-theory (DFT) calculations and the 7 Li nuclear magnetic resonance results, it is shown that the Li ions prefer to dominantly occupy the fourfold coordinated interstitial sites and fourfold coordinated Al sites. The systematic analysis of thermoluminescence glow curves, positron annihilation lifetime spectroscopies, and defect formation energies derived from DFT calculations reveals that the concentration of isolated Lu and Al vacancies as dominant acceptor defects is reduced by Li codoping, whilst the shallow Li i interstitial defects and the deep V O oxygen vacancies are introduced simultaneously. We propose that the lowering of hole trapping at defects resulting from Li codoping contributes to the scintillation-yield enhancement.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nucleation-controlled growth of superior lead-free perovskite Cs 3 Bi 2 I 9 single-crystals for high-performance X-ray detection

The organic-inorganic hybrid lead halide perovskites have emerged as a series of star materials for solar cells, lasers and detectors. However, the issues raised by the toxic lead element and marginal stability due to the volatile organic components have severely limited their potential applications. In this work, we develop a nucleation-controlled solution method to grow large size high-quality Cs 3 Bi 2 I 9 perovskite single crystals (PSCs). Using the technique, we harvest some centimeter-sized single crystals and achieved high device performance. We find that X-ray detectors based on PSCs exhibit high sensitivity of 1652.3 μC Gy air -1 cm -2 and very low detectable dose rate of 130 nGy air s -1 , both desired in medical diagnostics. In addition, its outstanding thermal stability inspires us to develop a high temperature X-ray detector with stable response at up to 100 °C. Furthermore, PSCs exhibit high X-ray imaging capability thanks to its negligible signal drifting and extremely high stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Revealing High Na-Content P2-Type Layered Oxides as Advanced Sodium-Ion Cathodes

Layered Na-based oxides with the general composition of Na x TMO 2 (TM: transition metal) have attracted significant attention for their high compositional diversity that provides tunable electrochemical performance for electrodes in sodium-ion batteries. The various compositions bring forward complex structural chemistry that is decisive for the layered stacking structure, Na-ion conductivity, and the redox activity, potentially promising new avenues in functional material properties. In this work, we have explored the maximum Na content in P2-type layered oxides and discovered that the high-content Na in the host enhances the structural stability; moreover, it promotes the oxidation of low-valent cations to their high oxidation states (in this case Ni 2+ ). This can be rationalized by the increased hybridization of the O(2p)-TM(3d-e g *) states, affecting both the local TM environment as well as the interactions between the NaO 2 and TMO 2 layers. These properties are highly beneficial for the Na storage capabilities as required for cathode materials in sodium-ion batteries. It leads to excellent Na-ion mobility, a large storage capacity (>100 mAh g –1 between 2.0-4.0 V), yet preventing the detrimental sliding of the TMO 2 layers (P2–O2 structural transition), as reflected by the ultralong cycle life (3000 (dis)charge cycles demonstrated). These findings expand the horizons of high Na-content P2-type materials, providing new insights of the electronic and structural chemistry for advanced cathode materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal boundary conductance between high thermal conductivity boron arsenide and silicon

Thermal boundary conductance (TBC) is important for heat dissipation in light-emitting diodes (LEDs). In this study, we predicted the TBC between the high thermal conductivity boron arsenide (BAs) and silicon (Si) by nonequilibrium molecular dynamics (MD) simulations. From the thermal conductivity accumulation function with respect to phonon frequency, the dominant phonon frequencies for heat conduction in BAs are extremely different from those in Si. However, our nonequilibrium MD simulations indicated that the TBC of the BAs/Si interface was still high compared to most other interfaces, even though there was a major frequency mismatch in the thermal conductivity accumulation function between BAs and Si. The primary reason for the high TBC is the overlap of phonon density of states between BAs and Si in the frequency range of 5–8 THz. The range of predicted TBC of the BAs/Si interface was between 200 and 300 MW/m2 K in the temperature range of 300–700 K, and the values of the TBC were not sensitive to the temperature. We also found that the TBCs in Si/BAs and Si/Ge interfaces were close to each other considering the simulation uncertainty. This work indicates BAs as an excellent material for heat dissipation across the interfaces.

Wei, Zhiyong (ORCID:000000018686451X)↗

Effect of Dual-Phase Heat Treatment on Microstructure and Mechanical Properties of S135 High-Strength Drill Pipe Steel

Effect of dual-phase heat treatment (DPHT) on microstructure and mechanical properties of S135 high-strength drill pipe steel was studied by means of optical microscope, scanning electron microscope and mechanical property testing. The results show that the ferrite–martensite dual-phase microstructures were obtained at 760-800 °C. With increase in DPHT temperature, the volume fraction of martensite increases and the ferrite decreases. When the DPHT temperature is low, martensite is distributed as an island on the ferrite matrix, and ferrite is distributed as an island on the martensite matrix when the DPHT temperature is high. The hardness and strength of the steel increase, the plasticity and toughness decrease, the steel changes from ductile fracture to brittle fracture and the micro-fracture morphology changes from dimple to cleavage with increase in DPHT temperature. The strain hardening exponent of the as-received steel shows one ‘n’ value, but exhibits two ‘n’ values after DPHT. When the DPHT temperature is 750 °C, the relative content of martensite in the duplex structure is 15-20%, and the impact energy of the steel is similar to that of the as-received S135 drill pipe steel, and the strength is increased by about 15%. Micropores and micro-cracks on the subsurface of tensile fracture surface are mainly formed at the martensite/ferrite phase boundary or in the martensite slit.

36 MATERIALS SCIENCE↗

First-principles search for alloying elements that increase corrosion resistance of Mg with second-phase particles of transition metal impurities

A significant challenge for applications of Mg alloys is their poor corrosion resistance and hence Mg alloys designs with built-in corrosion resistance are of significant interest. Corrosion can result from the coupling of anodic dissolution of Mg and cathodic reduction of water on impurities such as Iron (Fe)-rich second-phase particles. Experiments have shown that small quantities of Arsenic (As) or Germanium (Ge) can inhibit Mg corrosion, possibly slowing the hydrogen evolution reaction (HER) as the cathodic reaction on Fe surfaces. Since a broader experimental search across the periodic table for other Mg corrosion inhibiting elements is unavailable, we designed thermodynamic and HER criteria, and used high-throughput computations to search a pool of 68 elements including As and Ge that can segregate from bulk Mg to surfaces of Fe particles and impede the HER there. Our computational procedure predicts that six p-block elements meet these criteria, and they rank according to their ability to reduce H adsorption energies and the HER rate as follows: As > Ge > Si > Ga > P ≈ Al. Results for As, the most effective corrosion-inhibiting element, and Ge are in qualitative accord with recent experiments. Further, while none of the 68 elements was found to enhance H adsorption, the six p-block elements reduce H adsorption via strong orbital overlap (Pauli repulsion) between their outer-shell orbitals and the s orbitals of H adsorbates. These p-block elements are also found to have the potential to reduce HER on surfaces of Ni second-phase particles in Mg according to the same criteria, but not on surfaces of Cu second-phase particles.

36 MATERIALS SCIENCE↗

Sulfide Stress Corrosion Cracking Behavior of G105 and S135 High-Strength Drill Pipe Steels in H{sub 2}S Environment

Slow strain rate testing was employed to investigate the sulfide stress corrosion cracking (SSCC) behavior of low-carbon high-strength drill pipe steels (G105 and S135) in the simulated drilling environment containing H{sub 2}S. Results reveal that both G105 and S135 steels have a high SSCC susceptibility in the simulated drilling environment containing H{sub 2}S. In the range of experimental slow strain rate, the SSCC sensitivity of drill pipe steel increases with the decrease in slow strain rate, and the ductility and fracture properties of drill pipe steels also decrease obviously. With the increase in the steel strength, the SSCC sensitivity of the drill pipe steel increases, and the S135 drill pipe steel has higher SSCC sensitivity than G105. There is no obvious plastic deformation on the fracture surface of G105 and S135 steels in H{sub 2}S solution. The cracks of fracture sprout on the surface of the specimen, the instantaneous fracture zone is in the middle, and the fracture can be divided into the cracking and the final fracture zone. The SSCC mechanisms of two drill pipe steels are hydrogen embrittlement. The hydrogen enters the steel and reduces the binding force of the iron atom, resulting in cleavage fracture.

36 MATERIALS SCIENCE↗

Chlorinated Wide-Bandgap Donor Polymer Enabling Annealing Free Nonfullerene Solar Cells with the Efficiency of 11.5%

Substituting the hydrogen atoms on the conjugated side chain of a wide-bandgap polymer J52 with chlorine atoms can simultaneously increase the J sc , V oc , and FF of nonfullerene OSCs, leading to an efficiency boost from 3.78 to 11.53%, which is among the highest efficiencies for as-cast OSCs reported to date. To illustrate the impressive 3-fold PCE enhancement, the chlorination effect on the optical properties and energy levels of polymers, film morphology, and underlying charge dynamics is systematically investigated. Grazing incidence wide-angle X-ray scattering studies show that chlorinated J52-2Cl exhibits strong molecule aggregation, the preferred face-on orientation, and enhanced intermolecular pi-pi interactions, hence increasing the charge carrier mobility by 1 order of magnitude. Moreover, chlorination modifies the miscibility between the donor and acceptor and consequently optimizes the phase separation morphology of J52-2Cl:ITIC blend films. Finallyhese results highlight chlorination as a promising approach to achieve highly efficient as-cast OSCs without any extra treatment.

14 SOLAR ENERGY↗