Search NASA⌕ Search

Engineering topics

Liu, Tuo

Publications and source records attributed to Liu, Tuo.

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Investigation of Sub‐Bandgap Emission and Unexpected n‐Type Behavior in Undoped Polycrystalline CdSe x Te 1‐x

Abstract Se alloying has enabled significantly higher carrier lifetimes and photocurrents in CdTe solar cells, but these benefits can be highly dependent on CdSe x Te 1‐x processing. This work evaluates the optoelectronic, chemical, and electronic properties of thick (3 µm) undoped CdSe x Te 1‐x of uniform composition and varied processing conditions (CdSe x Te 1‐x evaporation rate, CdCl 2 anneal, Se content) chosen to reflect various standard device processing conditions. Sub‐bandgap defect emission is observed, which increased as Se content increased and with “GrV‐optimized CdCl 2 ” (i.e., CdCl 2 anneal conditions used for group‐V‐doped devices). Low carrier lifetime is found for GrV‐optimized CdCl 2 , slow CdSe x Te 1‐x deposition, and low‐Se films. Interestingly, all films (including CdTe control) exhibited n‐type behavior, where electron density increased with Se up to an estimated ≈10 17 cm −3 . This behavior appears to originate during the CdCl 2 anneal, possibly from Se diffusion leading to anion vacancy (e.g., V Se , V Te ) and Cl Te generation.

14 SOLAR ENERGY↗
DOE OSTI2023

Exciton Binding Energy in Organic Polymers: Experimental Considerations and Tuning Prospects

Discrepancies in reported values of exciton binding energy (E b ) for organic semiconductors (OSs) necessitate a comprehensive study. Traditionally, E b is defined as the difference between the transport gap (E t ) and the optical gap (E opt ). Here, the E b values of PBnDT‐TAZ polymer variants are determined using two commonly employed methods: a combination of ultraviolet photoemission spectroscopy and low‐energy inverse photoemission spectroscopy (UPS‐LEIPS) and solid‐state cyclic voltammetry (CV). E b values obtained by UPS‐LEIPS show low dispersion and no clear correlation with the polymer structure and thedielectric properties. In contrast, CV reveals a larger dispersion (200 meV‐1 eV) and an apparent qualitative E b ‐molecular structure correlation, as the lowest E b values are observed for oligo‐ethylene glycol side chains. This discrepancy is discussed by examining the implications of the traditional definition of E b . Additionally, the impact of both intrinsic and extrinsic factors contributing to the derived experimental values of E t is discussed. The differences in intrinsic and extrinsic factors highlight the context‐dependent nature of measurement when drawing global conclusions. Notably, the observed E b trend derived from CV is not intrinsic to the pure materials but likely linked to electrolyte swelling and associated changes in dielectric environment, suggesting that high‐efficiency single‐material organic photovoltaics with low E b may be possible via high dielectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Co-deposition of hole-selective contact and absorber for improving the processability of perovskite solar cells

Simplifying the manufacturing processes of renewable energy technologies is crucial to lowering the barriers to commercialization. In this context, to improve the manufacturability of perovskite solar cells (PSCs), here we have developed a one-step solution-coating procedure in which the hole-selective contact and perovskite light absorber spontaneously form, resulting in efficient inverted PSCs. We observed that phosphonic or carboxylic acids, incorporated into perovskite precursor solutions, self-assemble on the indium tin oxide substrate during perovskite film processing. They form a robust self-assembled monolayer as an excellent hole-selective contact while the perovskite crystallizes. Our approach solves wettability issues and simplifies device fabrication, advancing the manufacturability of PSCs. Our PSC devices with positive-intrinsic-negative (p-i-n) geometry show a power conversion efficiency of 24.5% and retain >90% of their initial efficiency after 1,200 h of operating at the maximum power point under continuous illumination. The approach shows good generality as it is compatible with different self-assembled monolayer molecular systems, perovskites, solvents and processing methods.

14 SOLAR ENERGY↗
DOE OSTI2022

Solvent-Free Manufacturing of Lithium-Ion Battery Electrodes via Cold Plasma

Slurry casting has been used to fabricate lithium-ion battery electrodes for decades, which involves toxic and expensive organic solvents followed by high-cost vacuum drying and electrode calendering. This work presents a new manufacturing method using a nonthermal plasma to create inter-particle binding without using any polymeric binding materials, enabling solvent-free manufacturing electrodes with any electrochemistry of choice. The cold-plasma-coating technique enables fabricating electrodes with thickness (>200 μm), high mass loading (>30 mg cm -2 ), high peel strength, and the ability to print lithium-ion batteries in an arbitrary geometry. This crosscutting, chemistry agnostic, platform technology would increase energy density, eliminate the use of solvents, vacuum drying, and calendering processes during production, and reduce manufacturing cost for current and future cell designs. Here, lithium iron phosphate and lithium cobalt oxide were used as examples to demonstrate the efficacy of the cold-plasma-coating technique. It is found that the mechanical peel strength of cold-plasma-coating-manufactured lithium iron phosphate is over an order of magnitude higher than that of slurry-casted lithium iron phosphate electrodes. Full cells assembled with a graphite anode and the cold-plasma-coating-lithium iron phosphate cathode offer highly reversible cycling performance with a capacity retention of 81.6% over 500 cycles. For the highly conductive cathode material lithium cobalt oxide, an areal capacity of 4.2 mAh cm -2 at 0.2 C is attained. We anticipate that this new, highly scalable manufacturing technique will redefine global lithium-ion battery manufacturing providing significantly reduced plant footprints and material costs.

25 ENERGY STORAGE↗
DOE OSTI2022

Photoactivated p-Doping of Organic Interlayer Enables Efficient Perovskite/Silicon Tandem Solar Cells

Solution-processed organic semiconductor layers on rough surfaces tend to vary widely in thickness, significantly hindering charge extraction in relevant optoelectronic devices. Herein, we report the photoactivated p-doping of hole-transporting material (HTM) to enhance hole extraction for (textured) perovskite/silicon tandem solar cells, making the device performance less sensitive to the variation of hole transport layer thickness. We used the ionic compound 4-isopropyl-4'-methyldiphenyliodonium tetrakis(penta-fluorophenyl-borate) (DPI-TPFB) as a p-type dopant in poly(triaryl amine) (PTAA), which we used as the HTM. We observed that light soaking DPI-TPFB-doped PTAA shows approximately 22 times higher conductivity compared with an undoped PTAA film, which translated into an improved fill factor (FF) for tandem solar cells. Our tandem solar cells achieved an ~80% FF and 27.8% efficiency and operated at their maximum power point for 200 h without loss of performance, in addition to retaining ~83% of initial performance over a month of operation in an outdoor environment.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS,S↗
DOE OSTI2021

Effect of Palladium‐Tetrakis(Triphenylphosphine) Catalyst Traces on Charge Recombination and Extraction in Non‐Fullerene‐based Organic Solar Cells

Abstract The effect of the cross‐coupling catalyst tetrakis(triphenylphosphine)palladium(0) (Pd(PPh 3 ) 4 ) on the performance of a model organic bulk‐heterojunction solar cell composed of a blend of poly([2,6′‐4,8‐di(5‐ethylhexylthienyl)benzo[1,2‐b;3,3‐b]dithiophene]{3‐fluoro‐2[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl}) (PTB7‐Th) donor and 3,9‐bis(2‐methylene‐((3‐(1,1‐dicyanomethylene)‐6,7‐difluoro)‐indanone))‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene (IOTIC‐4F) non‐fullerene acceptor is investigated. The effect of intentional addition of different amounts of Pd(PPh 3 ) 4 on morphology, free charge carrier generation, non‐geminate bulk trap‐ and surface trap‐assisted recombination as well as bimolecular recombination and charge extraction is quantified. This work shows that free charge carrier generation is affected significantly, while the impact of Pd(PPh 3 ) 4 on non‐geminate recombination processes is limited because the catalyst does not facilitate efficient trap‐assisted recombination. The studied system shows substantial robustness towards the addition of Pd(PPh 3 ) 4 in small amounts.

Schopp, Nora↗