Probing Domain-Boundary-Induced Structural Degradation in Single-Crystalline LiCoO2 by Nanoscale Imaging
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Liu, Yijin.
Explore the source record for details and available documents.
Electrocatalytic CO 2 reduction is garnering significant interest due to its potential applications in mitigating CO 2 and producing fuel. However, the scaling up of related catalysis is still hindered by several challenges, including the cost of the catalytic materials, low selectivity, small current densities to maintain desirable selectivity. In this study, Fluorine (F) atoms were introduced into an N-doped carbon-supported single nickel (Ni) atom catalyst via facile polymer-assisted pyrolysis. This method not only maintains the high atom utilization efficiency of Ni in a cost-effective and sustainable manner but also effectively manipulates the electronic structure of the active Ni-N 4 site through F doping. The catalyst has also been further optimized by controlling the F states, including convalent and semi-ionic states, by adjusting the fluorine sources involved. Consequently, this catalyst with unique structure exhibited comparable electrocatalytic performance for CO 2 -to-CO conversion, achieving a Faradaic efficiency (FE) of over 99% across a wide potential range and an exceptional CO evolution rate of 9.5 x 10 4 h -1 at -1.16 V vs reversible hydrogen electrode (RHE). It also delivered a practical current of 400 mA cm -2 while maintaining more than 95% CO FE. Experimental analysis combined with density functional theory (DFT) calculations have also shown that F-doping modifies the electron configuration at the central Ni-N 4 sites. In conclusion, this modification lowers the energy barrier for CO 2 activation, thereby facilitating the production of the crucial *COOH intermediate.
Not Available
Synchrotron transmission X-ray microscopy with absorption near edge structure (TXM-XANES) is a powerful tool for investigating the structure and composition of materials at nano- to meso-scales. It is, however, often challenged by high levels of noise that obscure critical details at the single-pixel level. To address this issue, a deep learning-based algorithm is developed for suppressing the image noise, grounded in self-supervised learning principles. In contrast to traditional image denoising methods, this approach successfully enhances the visibility of fine details while significantly reducing the noise in the X-ray images. Through this advancement, the potential of the approach for improving the accuracy and interpretability of the TXM-XANES data is demonstrated, thereby enabling more precise detection of nanoscale phenomena such as inhomogeneous cation redox and metal segregation in battery cathode materials. This technique offers an effective new avenue for harnessing the full potential of synchrotron TXM-XANES imaging, paving the way for a range of exciting new studies in materials science and beyond.
Single-crystalline layered oxide materials for lithium-ion batteries are featured by their excellent capacity retention over their polycrystalline counterparts, making them sought-after cathode candidates. Their capacity degradation, however, becomes more severe under high-voltage cycling, hindering many high-energy applications. It has long been speculated that the interplay among composition heterogeneity, lattice deformation, and redox stratification could be a driving force for the performance decay. The underlying mechanism, however, is not well-understood. In this study, we use X-ray microscopy to systematically examine single-crystalline NMC particles at the mesoscale. This technique allows us to capture detailed signals of diffraction, spectroscopy, and fluorescence, offering spatially resolved multimodal insights. Focusing on early high-voltage charging cycles, we uncover heterogeneities in valence states and lattice structures that are inherent rather than caused by electrochemical abuse. These heterogeneities are closely associated with compositional variations within individual particles. Our findings provide useful insights for refining material synthesis and processing for enhanced battery longevity and efficiency.
Not Available
The structural and chemical evolution of battery electrodes at the nanoscale plays an important role in affecting the cell performance. Nano-resolution X-ray microscopy has been demonstrated as a powerful technique for characterizing the evolution of battery electrodes under operating conditions with sensitivity to their morphology, compositional distribution and redox heterogeneity. In real-world batteries, the electrode could deform upon battery operation, causing challenges for the image registration which is necessary for several experimental modalities, e.g. XANES imaging. To address this challenge, this work develops a deep-learning-based method for automatic particle identification and tracking. This approach was not only able to facilitate image registration with good robustness but also allowed quantification of the degree of sample deformation. The effectiveness of the method was first demonstrated using synthetic datasets with known ground truth. The method was then applied to an experimental dataset collected on an operating lithium battery cell, revealing a high degree of intra- and interparticle chemical complexity in operating batteries.
To improve lithium-ion battery technology, it is essential to probe and comprehend the microscopic dynamic processes that occur in a real-world composite electrode under operating conditions. The primary and secondary particles are the structural building blocks of battery cathode electrodes. Their dynamic inconsistency has profound but not well-understood impacts. In this research, we combine operando coherent multi-crystal diffraction and optical microscopy to examine the chemical dynamics in local domains of layered oxide cathode. Our results not only pinpoint the asynchronicity of the lithium (de)intercalation at the sub-particle level, but also reveal sophisticated diffusion kinetics and reaction patterns, involving various localized processes, e.g., chemical onset, reaction front propagation, domains equilibration, particle deformation and motion. These observations shed new lights onto the activation and degradation mechanisms of state-of-the-art battery cathode materials.
High-resolution imaging with compositional and chemical sensitivity is crucial for a wide range of scientific and engineering disciplines. Although synchrotron X-ray imaging through spectromicroscopy has been tremendously successful and broadly applied, it encounters challenges in achieving enhanced detection sensitivity, satisfactory spatial resolution, and high experimental throughput simultaneously. In this work, based on structured illumination, we develop a single-pixel X-ray imaging approach coupled with a generative image reconstruction model for mapping the compositional heterogeneity with nanoscale resolvability. This method integrates a full-field transmission X-ray microscope with an X-ray fluorescence detector and eliminates the need for nanoscale X-ray focusing and raster scanning. We experimentally demonstrate the effectiveness of our approach by imaging a battery sample composed of mixed cathode materials and successfully retrieving the compositional variations of the imaged cathode particles. Bridging the gap between structural and chemical characterizations using X-rays, this technique opens up vast opportunities in the fields of biology, environmental, and materials science, especially for radiation-sensitive samples.
P2-Na 0.67 Ni 0.33 Mn 0.67 O 2 represents a promising cathode for Na-ion batteries, but it suffers from severe structural degradation upon storing in a humid atmosphere and cycling at a high cutoff voltage. Here we propose an in situ construction to achieve simultaneous material synthesis and Mg/Sn cosubstitution of Na 0.67 Ni 0.33 Mn 0.67 O 2 via one-pot solid-state sintering. Here, the materials exhibit superior structural reversibility and moisture insensitivity. In-operando XRD reveals an essential correlation between cycling stability and phase reversibility, whereas Mg substitution suppressed the P2–O2 phase transition by forming a new Z phase, and Mg/Sn cosubstitution enhanced the P2–Z transition reversibility benefiting from strong Sn–O bonds. DFT calculations disclosed high chemical tolerance to moisture, as the adsorption energy to H 2 O was lower than that of the pure Na 0.67 Ni 0.33 Mn 0.67 O 2 . A representative Na 0.67 Ni 0.23 Mg 0.1 Mn 0.65 Sn 0.02 O 2 cathode exhibits high reversible capacities of 123 mAh g –1 (10 mA g –1 ), 110 mAh g –1 (200 mA g –1 ), and 100 mAh g –1 (500 mA g –1 ) and a high capacity retention of 80% (500 mA g –1 , 500 cycles).
Abstract During solid‐state calcination, with increasing temperature, materials undergo complex phase transitions with heterogeneous solid‐state reactions and mass transport. Precise control of the calcination chemistry is therefore crucial for synthesizing state‐of‐the‐art Ni‐rich layered oxides (LiNi 1‐x‐y Co x Mn y O 2 , NRNCM) as cathode materials for lithium‐ion batteries. Although the battery performance depends on the chemical heterogeneity during NRNCM calcination, it has not yet been elucidated. Herein, through synchrotron‐based X‐ray, mass spectrometry microscopy, and structural analyses, it is revealed that the temperature‐dependent reaction kinetics, the diffusivity of solid‐state lithium sources, and the ambient oxygen control the local chemical compositions of the reaction intermediates within a calcined particle. Additionally, it is found that the variations in the reducing power of the transition metals (i.e., Ni, Co, and Mn) determine the local structures at the nanoscale. The investigation of the reaction mechanism via imaging analysis provides valuable information for tuning the calcination chemistry and developing high‐energy/power density lithium‐ion batteries.
Ni-rich layered oxides as high-capacity battery cathodes suffer from degradation at high voltages. Here, we utilize a dry surface modification method, mechanofusion (MF), to achieve enhanced battery stability. The simplicity, high yield, and flexibility make it cost-effective and highly attractive for processing at the industrial scale. The underlying mechanisms responsible for performance improvement are unveiled by a systematic study combining multiple probes, e.g., 3D nano-tomography, spectroscopic imaging, in situ synchrotron diffraction, and finite element analysis (FEA). MF affects the bulk crystallography by introducing partially disordered structure, microstrain, and local lattice variation. Furthermore, the crack initiation and propagation pattern during delithiation are regulated and the overall mechanical fracture is reduced after such surface coating. We validate that MF can alter the bulk charging pathways. Such a synergic effect between surface modification and bulk charge distribution is fundamentally important for designing next-generation battery cathode materials.
The high interfacial resistance and lithium (Li) dendrite growth are two major challenges for solid-state Li batteries (SSLBs). The lack of understanding on the correlations between electronic conductivity and Li dendrite formation limits the success of SSLBs. Here, by diluting the electronic conductor from the interphase to bulk Li during annealing of the aluminium nitride (AlN) interlayer, we changed the interphase from mixed ionic/electronic conductive to solely ionic conductive, and from lithiophilic to lithiophobic to fundamentally understand the correlation among electronic conductivity, Li dendrite, and interfacial resistance. During the conversion-alloy reaction between AlN and Li, the lithiophilic and electronic conductive Li x Al diffused into Li, forming a compact lithiophobic and ionic conductive Li 3 N, which achieved an ultrahigh critical current density of 2.6/14.0 mA/cm 2 in the time/capacity-constant mode, respectively. The fundamental understanding on the effect of interphase nature on interfacial resistance and Li dendrite suppression will provide guidelines for designing high-performance SSLBs.
Lithium-ion battery (LIB) is a broadly adopted technology for energy storage. With increasing demands to improve the rate capability, cyclability, energy density, safety, and cost efficiency, it is crucial to establish an in-depth understanding of the detailed structural evolution and cell-degradation mechanisms during battery operation. Here, we present a laboratory-based high-resolution and high-throughput X-ray micro–computed laminography approach, which is capable of in situ visualizing of an industry-relevant lithium-ion (Li-ion) pouch cell with superior detection fidelity, resolution, and reliability. This technique enables imaging of the pouch cell at a spatial resolution of 0.5 μm in a laboratory system and permits the identification of submicron features within cathode and anode electrodes. We also demonstrate direct visualization of the lithium plating in the imaged pouch cell, which is an important phenomenon relevant to battery fast charging and low-temperature cycling. Our development presents an avenue toward a thorough understanding of the correlation among multiscale structures, chemomechanical degradation, and electrochemical behavior of industry-scale battery pouch cells.
We report in Li-ion batteries, the mechanical degradation initiated by micro cracks is one of the bottlenecks for enhancing the performance. Quantifying the crack formation and evolution in complex composite electrodes can provide important insights into electrochemical behaviors under prolonged and/or aggressive cycling. However, observation and interpretation of the complicated crack patterns in battery electrodes through imaging experiments are often time-consuming, labor intensive, and subjective. Herein, a deep learning-based approach is developed to extract the crack patterns from nanoscale hard X-ray holo-tomography data of a commercial 18650-type battery cathode. Efficient and effective quantification of the damage heterogeneity with automation and statistical significance is demonstrated. The crack characteristics are further associated with the active particles’ packing densities and a potentially viable architectural design is discussed for suppressing the structural degradation in an industry-relevant battery configuration.
Transition metal dissolution in layered cathodes is one of the most intractable issues that deteriorates the battery performance and lifetime. It not only aggravates the structure degradation in cathode, but also damages the solid electrolyte interphase in anode and even induce the formation of lithium dendrites. In this work, we investigate the dissolution behaviors of polycrystalline and single-crystalline layered cathode via operando X-ray imaging techniques. The described cathode particle morphology appears to have a significant impact on the evolution of the dissolution dynamics. As a mitigation strategy, we reveal that doping with trace amount of Zr in the layered cathode could improve its robustness against the transition metal dissolution. Our finding provides valuable insights for designing the next-generation highly-stable layered battery cathodes.
Nickel-rich layered cathode materials promise high energy density for next-generation batteries when coupled with lithium metal anodes. However, the practical capacities accessible are far less than the theoretical values due to their structural instability during cycling, especially when charged at high voltages. Here we demonstrate that stable cycling with an ultra-high cut-off voltage of 4.8 V can be realized by using an appropriate amount of lithium difluorophosphate in a common commercial electrolyte. The Li||LiNi 0.76 Mn 0.14 Co 0.10 O 2 cell retains 97% of the initial capacity (235 mAh g -1 ) after 200 cycles. The cycling stability is ascribed to the robust interphase on the cathode. It is formed by lithium difluorophosphate decomposition, which is facilitated by the catalytic effect of transition metals. The decomposition products (Li 3 PO 4 and LiF) form a protective interphase. This suppresses transition metal dissolution and cathode surface reconstruction. It also facilitates uniform Li distribution within the cathode, effectively mitigating the strain and crack formation.