Search NASA⌕ Search

Engineering topics

Liu, Z

Publications and source records attributed to Liu, Z.

125 records · Page 7

High-Pressure Infrared Spectroscopy on the Hydrous Magnesium Silicates, Phase D and Phase E

Phases D and E are hydrous magnesium silicates that are stable at high-pressure-temperature conditions and could serve as H2O carriers in the Earth's mantle, especially in subducting slabs. Using synchrotron infrared (IR) spectroscopy, we measured the infrared spectra of polycrystalline samples of phases D and E to 42 and 41 GPa, respectively. For both phases, at least three broad OH stretch vibrations were observed at elevated pressures indicating that each phase has multiple hydrogen positions that exhibit disorder. No structural phase transition or amorphization was observed for either phase over the measured pressure range. The mode Grueneisen parameters of phases D and E are in the range of -0.12 to 1.14 and -0.17 to 0.83, respectively, with mean values of 0.41 (phase D) and 0.31 (phase E). Using empirical correlations of OH frequency and Ocdots, three dots, centeredH and Ocdots, three dots, centeredO bond lengths; the six OH vibrations of phase D at ambient pressure have corresponding Ocdots, three dots, centeredH and Ocdots, three dots, centeredO bond distances in the range of 1.519-1.946 Angstroms and 2.225-2.817 Angstroms, whereas the four OH vibrations of phase E have the corresponding Ocdots, three dots, centeredH and Ocdots, three dots, centeredO bond distances in the range of 1.572-2.693 Angstroms and 2.557-2.986 Angstroms. These ranges encompass values reported from single-crystal X-ray diffraction measurements. At high pressures, the observable OH stretching vibrations exhibit both positive and negative pressure slopes. Our high-pressure infrared spectra for phase D do not support the occurrence of hydrogen symmetrization as predicted by first-principles calculations.

43 PARTICLE ACCELERATORS↗

PtMo Alloy and MoOx@Pt Core-Shell Nanoparticles as Highly CO-Tolerant Electrocatalysts

PtMo alloy and MoOx Pt core-shell nanoparticles (NPs) were successfully synthesized by a chemical coreduction and sequential chemical reduction method, respectively. Both the carbon-supported alloy and core-shell NPs show substantially higher CO tolerance, compared to the commercialized E-TEK PtRu alloy and Pt catalyst. These novel nanocatalysts can be potentially used as highly CO-tolerant anode electrocatalysts in proton exchange membrane fuel cells.

30 DIRECT ENERGY CONVERSION↗

Structural and Functional Studies of Aspergillus oryzae Cutinase: Enhanced Thermostability and Hydrolytic Activity of Synthetic Ester and Polyester Degradation

Cutinases are responsible for hydrolysis of the protective cutin lipid polyester matrix in plants and thus have been exploited for hydrolysis of small molecule esters and polyesters. Here we explore the reactivity, stability, and structure of Aspergillus oryzae cutinase and compare it to the well-studied enzyme from Fusarium solani. Two critical differences are highlighted in the crystallographic analysis of the A. oryzae structure: (i) an additional disulfide bond and (ii) a topologically favored catalytic triad with a continuous and deep groove. These structural features of A. oryzae cutinase are proposed to result in an improved hydrolytic activity and altered substrate specificity profile, enhanced thermostability, and remarkable reactivity toward the degradation of the synthetic polyester polycaprolactone. The results presented here provide insight into engineering new cutinase-inspired biocatalysts with tailor-made properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Pressure Far- and Mid-Infrared Study of 1,3,5-Triamino-2,4,6-trinitrobenzene

Synchrotron infrared measurements of 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) have been performed in the far-IR and mid-IR spectral regions up to {approx}30 and {approx}40 GPa, respectively. For the far-IR experiment, no pressurizing medium was used, whereas KBr was utilized as a pressurizing medium for the mid-IR experiment. For both experiments, pressure was cycled and IR spectra were recorded at various pressures to ascertain sample survival. In the high frequency region ({approx}3000 cm{sup -1}) of the mid-IR spectra, the peak frequencies of the NH{sub 2} symmetric and antisymmetric vibrational modes steadily decrease with increasing pressure, indicating strengthening of intermolecular hydrogen bonding with pressure. In both experiments, no apparent phase transition was observed to the highest pressures studied.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ionic High-Pressure Form of Elemental Boron

This Letter presents the results of high-pressure experiments and ab initio evolutionary crystal structure predictions, and found a new boron phase that we named gamma-B28. This phase is comprised of icosahedral B12 clusters and B2 pairs in a NaCl-type arrangement, stable between 19 and 89 GPa, and exhibits evidence for charge transfer (for which our best estimate is delta approximately 0.48) between the constituent clusters to give (B2)delta+(B12)delta-. We have recently found that the same high-pressure boron phase may have given rise to the Bragg reflections reported by Wentorf in 1965 (ref. 1), although the chemical composition was not analysed and the data (subsequently deleted from the Powder Diffraction File database) seems to not have been used to propose a structure model. We also note that although we used the terms 'partially ionic' and 'ionic' to emphasize the polar nature of the high-pressure boron phase and the influence this polarity has on several physical properties of the elemental phase, the chemical bonding in gamma-B28 is predominantly covalent.

36 MATERIALS SCIENCE↗

In situ High-pressure Study of Diborane by Infrared Spectroscopy

As the simplest stable boron hydride in its condensed phase, diborane exhibits an interesting structural chemistry with uniquely bridged hydrogen bonds. Here we report the first room-temperature infrared (IR) absorption spectra of solid diborane compressed to pressures as high as 50 GPa using a diamond anvil cell. At room temperature and 3.5 GPa, the IR spectrum of diborane displays rich sharply resolved fundamentals and overtones of the IR active bands, consistent with the previous low-temperature IR measurements of condensed diborane at ambient pressure. When compressed stepwise to 50 GPa, several structural transformations can be identified at pressures of 3.5 GPa, 6.9 GPa and 14.7 GPa, as indicated by the changes in the band profile as well as the pressure dependence of the characteristic IR modes and bandwidths. These transformations can be interpreted as being enhanced intermolecular interactions resulting from compression. The geometry of the four-member ring of B{sub 2}H{sub 6}, however, does not seem to be altered significantly during the transformations and the B{sub 2}H{sub 6} molecule remains chemically stable up to 50 GPa.

08 HYDROGEN↗

Anomalous Optical and Electronic Properties of Dense Sodium

Synchrotron infrared spectroscopy on sodium shows a transition from a high reflectivity, nearly free-electron metal to a low-reflectivity, poor metal in an orthorhombic phase at 118 GPa. Optical spectra calculated within density functional theory (DFT) agree with the experimental measurements and predict a gap opening in the orthorhombic phase at compression beyond its stability field, a state that would be experimentally attainable by appropriate choice of pressure-temperature path. We show that a transition to an incommensurate phase at 125 GPa results in a partial recovery of good metallic character up to 180 GPa, demonstrating the strong relationship between structure and electronic properties in sodium.

36 MATERIALS SCIENCE↗

Far-infrared Dielectric and Vibrational Properties of Nonstoichiometric Wüstite at High Pressure

The far-infrared reflectivity of Fe0.91O was investigated from atmospheric pressure up to 33 GPa at room temperature using synchrotron Fourier transform infrared reflectivity techniques in conjunction with the diamond-anvil cell from 100-700 cm-1. The frequency of the fundamental transverse optic (TO) mode was found to be nearly independent of pressure up to 4.6 GPa, followed by an increase in the TO frequency with pressure up to the rhombohedral phase transition at {approx}8 GPa. In addition, a second weak mode at 583 cm-1 at atmospheric pressure was well resolved and found to shift to higher frequency and increase in strength with pressure. This localized mode arises from the presence of vacancies in the crystal structure, and the relative strength of this mode suggests pressure-induced charge localization near the vacancy sites. The data was fit with the classical Lorentz model with the addition of a plasmon resonance. This allowed an estimation of the electrical conductivity as well as plasmon-phonon coupling energies. The pressure dependencies of the dielectric properties of westite have been quantified, and their pressure derivatives show a change in sign near the pressure-induced rhombohedral phase transition. Classical theories relating dielectric, vibrational, and elastic properties are evaluated, and in the case of the bulk modulus, the theory fails to reproduce accepted literature values.

36 MATERIALS SCIENCE↗

In Situ High-Pressure Study of Ammonia Borane by Raman and IR Spectroscopy

Pressure-induced structural transformations of the ammonia borane complex (NH3{center_dot}BH3) were investigated in diamond anvil cells by Raman spectroscopy and synchrotron IR spectroscopy up to 14 GPa at room temperature. Starting with a disordered tetragonal structure, NH3{center_dot}BH3 is found to undergo several transformations upon compression as monitored by in situ Raman measurements. These transformations are indicated by the sequential changes of characteristic Raman modes as well as by the pressure dependence of these modes. Synchrotron IR absorption spectroscopy provided supplementary and consistent information about the structural evolution of NH3{center_dot}BH3 under compression. Decompression measurements on NH3{center_dot}BH3 suggest the pressure-induced transformations are reversible in the entire pressure region. The combined Raman and IR data allowed analysis of possible high-pressure structures of NH3{center_dot}BH3. Our study significantly complements previous high-pressure Raman studies by providing new information on the structures and stabilities of NH3{center_dot}BH3.

43 PARTICLE ACCELERATORS↗

Structural Transitions and Electron Transfer in Coffinite, USiO4, at High Pressure

The compressibility, phase stability, and vibrational properties of coffinite (USiO4) were studied by in situ X-ray diffraction and infrared (IR) measurements at high pressures. An irreversible phase transition from the zircon-type to scheelite-type structure was found to occur at 14-17 GPa. Accompanying the structural transition, partial amorphization was also evident in the XRD analysis. The predicted transition pressure calculated by density functional theory is in good agreement with the experimental results. IR spectra also suggest that water is incorporated into the coffinite structure, and a pressure-induced electron transfer (U4+ -> U5+) may also occur.

58 GEOSCIENCES↗

Single-particle behavior at N=126: Isomeric decays in neutron-rich {sup 204}Pt

The four proton-hole nucleus {sup 204}Pt was populated in the fragmentation of an E/A=1 GeV {sup 208}Pb beam. The yrast structure of {sup 204}Pt has been observed up to angular momentum I=10({Dirac_h}/2{pi}) by detecting delayed {gamma}-ray transitions originating from metastable states. These long-lived excited states have been identified to have spin-parities of I{sup {pi}}=(10{sup +}), (7{sup -}), and (5{sup -}) and half-lives of T{sub 1/2}=146(14) ns, 55(3){mu}s, and 5.5(7){mu}s, respectively. The structure of the magic N=126 {sup 204}Pt nucleus is discussed and understood in terms of the spherical shell model. The data suggest a revision of the two-body interaction for N=126, Z<82, which determines the evolution of nuclear structure toward the r-process waiting point nuclei.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

MICROSCANNING XRF, XANES, AND XRD STUDIES OF THEDECORATED SURFACE OF ROMAN TERRA SIGILLATA CERAMICS

Different microscanning synchrotron techniques were used to better understand the elaboration process and origins of Terra Sigillata potteries from the Roman period. A mixture Gallic slip sample cross-section showing red and yellow colors was studied. The small (micron) size of the X-ray beam available at Stanford Synchrotron Radiation Laboratory (SSRL) and Advanced Light Source (ALS) synchrotron sources, coupled with the use of a sample scanning stage allowed us to spatially resolve the distribution of the constitutive mineral phases related to the chemical composition. Results show that red color is a result of iron-rich hematite crystals and the yellow part is a result of the presence of Ti-rich rutile-type phase (brookite). Volcanic-type clay is at the origin of these marble Terra Sigillata.

36 MATERIALS SCIENCE↗

The Effectiveness of HCl and HF Cleaning of Si0.85Ge0.15 Surface

The cleaning of Si{sub 0.85}Ge{sub 0.15} surfaces using HCl and HF solutions is studied using synchrotron radiation photoelectron spectroscopy. The HF solution is found to be effective in removing both the Si oxide and the Ge oxide while the HCl solution can only remove part of the Ge oxide. For samples treated with HF, four spectral components are needed to fit the Ge 3d photoemission spectra. One is the bulk component and the other three are attributed to the surface Ge atoms with mono-hydride, di-hydride and tri-hydride terminations, respectively.

43 PARTICLE ACCELERATORS↗

Light baryon masses with dynamical twisted mass fermions

We present results on the mass of the nucleon and the {delta} using two dynamical degenerate twisted mass quarks and the tree-level Symanzik improved gauge action. The evaluation is performed at four quark masses corresponding to a pion mass in the range of about 300-600 MeV on lattices of 2.1-2.7 fm at three lattice spacings less than 0.1 fm. We check for cutoff effects by evaluating these baryon masses on lattices of spatial size 2.1 fm at {beta}=3.9 and {beta}=4.05 and on a lattice of 2.4 fm at {beta}=3.8. The values we find are compatible within our statistical errors. Lattice results are extrapolated to the physical limit using continuum chiral perturbation theory. Performing a combined fit to our lattice data at {beta}=3.9 and {beta}=4.05 we find a nucleon mass of 963{+-}12(stat){+-}8(syst) MeV where we used the lattice spacings determined from the pion decay constant to convert to physical units. The systematic error due to the chiral extrapolation is estimated by comparing results obtained at O(p{sup 3}) and O(p{sup 4}) heavy baryon chiral perturbation theory. The nucleon mass at the physical point provides an independent determination of the lattice spacing. Using heavy baryon chiral perturbation theory at O(p{sup 3}) we find a{sub {beta}}{sub =3.9}=0.0889{+-}0.0012(stat){+-}0.0014(syst) fm, and a{sub {beta}}{sub =4.05}=0.0691{+-}0.0010(stat){+-}0.0010(syst) fm, in good agreement with the values determined from the pion decay constant. Using results from our two smaller lattices spacings at constant r{sub 0}m{sub {pi}} we estimate the continuum limit and check consistency with results from the coarser lattice. Results at the continuum limit are chirally extrapolated to the physical point. Isospin violating lattice artifacts in the {delta}-system are found to be compatible with zero for the values of the lattice spacings used in this work. Performing a combined fit to our lattice data at {beta}=3.9 and {beta}=4.05 we find for the masses of the {delta}{sup ++,-} and {delta}{sup +,0} 1315{+-}24(stat) MeV and 1329{+-}30(stat) MeV, respectively. We confirm that in the continuum limit they are also degenerate.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The work function of sub-monolayer cesium-covered gold: A photoelectronspectroscopy study

Using visible and X-ray photoelectron spectroscopy we measured the work function of a Au(111) surface at a well-defined sub-monolayer coverage of Cs. For a Cs coverage producing a photoemission maximum with a He-Ne laser, the work function is 1.61 {+-} 0.08 eV consistent with previous assumptions used to analyze vibrationally promoted electron emission. A discussion of possible Cs layer structures is also presented.

36 MATERIALS SCIENCE↗

Photoemission Study of Cs-NF3 Activated GaAs(100) Negative Electron Affinity Photocathodes

GaAs based negative electron affinity photocathodes activated with Cs and NF{sub 3} are used as polarized electron sources for linear accelerators. It is generally believed that the activation layer consists of CsF. The activation layers of Cs-NF{sub 3} on GaAs photocathodes are herein investigated using synchrotron radiation photoelectron spectroscopy (SR-PES). F1s, N1s and other core levels are recorded at photon energies ranging from 70eV to 820eV. Surprisingly, a significant amount of nitrogen is observed in the activation layers. Two distinct species of nitrogen are observed, one of which decreases along with the Fluorine signal as the yield of the photocathode decays with time.

43 PARTICLE ACCELERATORS↗