Search NASA⌕ Search

Engineering topics

Livescu, Veronica

Publications and source records attributed to Livescu, Veronica.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Effects of heat treatment and build orientation on the evolution of $ϵ$ and $α'$ martensite and strength during compressive loading of additively manufactured 304L stainless steel

In this paper, the effect of heat-treatment and build orientation on martensitic phase transformation in additively manufactured (AM) 304L stainless steel is studied and compared with conventionally produced wrought material. The relationships between observed martensitic transformations and material microstructures and their effects on mechanical strength are established through experimental observations. In situ high-energy X-ray powder diffraction measurements were performed to monitor the evolution of $ϵ$ and $α'$ martensite during compressive loading of stainless steel. Electron backscatter diffraction (EBSD) was used to provide insight on initial grain morphology, crystallographic misorientation within grains, and crystallographic texture. Heat treatment alters the microstructure of AM samples creating different initial conditions. This difference in starting microstructure resulted in variability in martensitic transformation during compressive deformation. The rate of martensitic transformation decreased for AM samples treated with temperatures up to 1100°C, after which the AM microstructures recrystallized, resulting in increased rate of martensitic transformation for those samples treated at higher temperatures. It was also observed that aligning the axis of compression with the AM build direction resulted in a lower rate of strain-induced martensite formation as opposed to aligning the compression axis perpendicular to it. More favorable distribution of crystal orientations in the latter loading orientation promoted martensitic transformation. These and additional experimental observations from EBSD in terms of kernel average misorientation, mean grain orientation spread, and mean crystallite size reveal strong microstructural effects on strength of additively manufactured metallic materials.

304L stainless steel↗
DOE OSTI2020

Proton irradiation and characterization of additively manufactured 304L stainless steels

Irradiations were performed with 1.5 MeV protons to 0.6 dpa at 40–150 °C on additively manufactured (AM) 304L stainless steel and the changes in microstructure and mechanical behavior after irradiation were compared to wrought 304L stainless steel. Interestingly, all microstructural and hardness results after irradiation suggest the samples evolve toward a similar state, despite significant differences in the unirradiated microstructures and hardness values. A TEM and nanoindentation-based investigation of before and after proton irradiation at 40–150 °C is presented. Results are interpreted in terms of initial dislocation content, dislocation structures, and microstructural and chemical homogeneity.

36 MATERIALS SCIENCE↗
DOE OSTI2019

A comparison of adiabatic shear bands in wrought and additively manufactured 316L stainless steel using nanoindentation and electron backscatter diffraction

The resistance of stainless steels to shear localization is dependent on processing and microstructure. The amount of research evaluating the shear response of additively manufactured (AM) stainless steels compared to traditionally manufactured ones is limited. To address this gap, experiments were performed on directed energy deposition AM as-built and wrought 316L stainless steel using a forced shear technique with a hat-shaped specimen and a Split-Hopkinson pressure bar. The resulting adiabatic shear bands were characterized with electron backscatter diffraction (EBSD) and nanoindentation to quantify the changes in microstructure and deformation hardening across shear band regions and between the wrought and AM materials. Despite significant differences between the wrought and AM materials including the forced shear response, the postmortem states of work hardening due to the shear band deformation are nearly the same. The maximum nanoindentation stresses occurred in the shear band center with similar magnitudes and only minor differences away from the shear band. Although EBSD data cannot be resolved in the shear band center, misorientation trends, particularly grain reference orientation deviation, were found to closely resemble nanoindentation trends. In conclusion, the combination of EBSD misorientation and nanoindentation, which are linked through changes in dislocation density, is a viable protocol to quantify local changes to macroscopically applied deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Three-dimensional explicit finite element formulation for shear localization with global tracking of embedded weak discontinuities

Shear localization is a damage mechanism characterized by the concentration of plastic deformation within thin bands of materials, often observed as a precursor to failure in metals. In this study, we present a three-dimensional explicit finite element formulation with embedded weak discontinuities for the treatment of shear localization under dynamic loading conditions. In this formulation, the onset of localization is detected via a material stability analysis suitable for rate-sensitive materials, and the continuity of propagating shear bands is ensured using a global tracking strategy involving a heat-conduction type boundary value problem, solved for a scalar level set function over the global domain of the problem. In addition, we propose a modified quadrature rule that is used to compute the contribution of an individual element to the global finite element arrays, taking into account the position of the embedded shear band within that element.

42 ENGINEERING↗
DOE OSTI2019

Using In Situ Neutron Diffraction to Isolate Specific Features of Additively Manufactured Microstructures in 304L Stainless Steel and Identify Their Effects on Macroscopic Strength

Additive manufacturing of metal components results in unique microstructures with, necessarily, mechanical properties that are distinct from conventionally produced components. In this paper, four distinct microstructural features associated with directed energy deposition of 304L stainless steels, their stability, and their influences on flow strength were examined. These were (1) high dislocation density comparable with deformed materials, (2) increased ferrite content, (3) local chemical heterogeneity, and (4) tortuous grain morphology. In situ neutron diffraction measurements were used to monitor the evolution of the as-built microstructure during post-build heat treatment and relate the specific microstructural features to the strength behavior of the material following the heat treatment. The increased flow strength of the additively manufactured material relative to wrought counterparts is found to be due primarily to an increased dislocation density in the as-built material. However, the increased dislocation density does not completely account for the increased strength and it is hypothesized that some of the additional strength is related to the unique AM grain structure.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Structural representation of additively manufactured 316L austenitic stainless steel

Three 316L stainless steel materials are studied and reported upon; wrought, as-built additively manufactured (AM), and heat-treated AM material. The AM material was produced from the laser engineered net shaping (LENS) process. Macroscopic uniaxial compression stress-strain curves were obtained for all three materials. The curves were similar for the wrought and heat-treated AM materials but the as-built AM material demonstrated approximately 1.7 times greater flow stress at any given level of strain than the other two materials. Electron-backscatter diffraction analysis of the materials also showed that the microstructures of the three materials differed; with complex grain morphology for the as-built AM material. The mean grain size of each of the three materials also differed. Furthermore, the initial dislocation density was also measured with neutron diffraction and line-profile analysis for both wrought and as-built AM materials with the density in the AM material approximately 2.5 times greater.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Additively manufactured tantalum microstructures

Additively manufacturing tantalum is a challenging process in which obstacles are stemming from the high melting temperature and susceptibility to oxidation of tantalum. In this paper, several combinations of deposition parameters were considered in an effort to obtain fully dense additively manufactured tantalum produced on an EOSINT M280 DMLS system. Deposition parameters significantly affect the resulting microstructure of additively manufactured tantalum, altering grain morphology, grain size, crystallographic preferred orientation, and deposition porosity. Due to the nature of the laser sintering process applied, which implies large directional temperature gradients, the resulting microstructures were strongly columnar along the building direction. Microstructural differences for different deposition conditions manifested themselves in both grain morphology and preferred crystal orientations in the columnar grains. Deposition speed and laser power were important parameters to consider for obtaining porosity-free material. Finally, stripe width had the most significant effect on grain growth.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Signatures of the unique microstructure of additively manufactured steel observed via diffraction

A series of measurements were designed to gain confidence in the interpretation of the peak breadth in diffraction patterns collected from additively manufactured material, which has a novel microstructure in comparison to the well understood microstructure of wrought materials. Stainless steels made with two additive manufacturing techniques were compared to wrought material. Similar patterns observed in the scattering vector dependence for additively manufactured and deformed wrought materials suggested that the broadening in both materials was related to dislocations. Finally, this was confirmed by heat-treatment, during which both materials exhibited recovery due to the annealing of dislocations at the same temperature.

304L stainless-steel↗
DOE OSTI2018

Impact of Defects in Powder Feedstock Materials on Microstructure of 304L and 316L Stainless Steel Produced by Additive Manufacturing

Recent work in both 304L and 316L stainless steel produced by additive manufacturing (AM) has shown that in addition to the unique, characteristic microstructures formed during the process, a fine dispersion of sub-micron particles, with a chemistry different from either the powder feedstock or the expected final material, are evident in the final microstructure. Such fine-scale features can only be resolved using transmission electron microscopy (TEM) or similar techniques. The present paper uses electron microscopy to study both the initial powder feedstock and microstructures in final AM parts. Special attention is paid to the chemistry and origin of these nanoscale particles in several different metal alloys, and their impact on the final build. Finally, comparisons to traditional, wrought material will be made.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Finite element formulation with embedded weak discontinuities for strain localization under dynamic conditions

Here, we present an explicit finite element formulation designed for the treatment of strain localization under highly dynamic conditions. We also used a material stability analysis to detect the onset of localization behavior. Finite elements with embedded weak discontinuities are employed with the aim of representing subsequent localized deformation accurately. The formulation and its algorithmic implementation are described in detail. Numerical results are presented to illustrate the usefulness of this computational framework in the treatment of strain localization under highly dynamic conditions, and to examine its performance characteristics in the context of two-dimensional plane-strain problems.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Comparative Assessment of Copper-Coated Kapton: Analysis of Microclad from Several Manufacturing Lots

Microclad is a composite material consisting of a thin copper coating applied on a single side over a Kapton substrate. Kapton is the commercial designator for polyimide supplied by DuPont. Microclad is a key material in detonator manufacture and function. Detonators which utilize Microclad function when a large current applied through a thin bridge etched into the copper produces a plasma, accelerating a Kapton flyer into an explosive (PETN) pellet. The geometry and properties of the Microclad are a critical element of this process.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Investigation of the shear response and geometrically necessary dislocation densities in shear localization in high-purity titanium

The influence of microstructural anisotropy on shear response of high-purity titanium was studied using the compact forced-simple-shear specimen (CFSS) loaded under quasi-static loading conditions. Post-mortem characterization reveals significant difference in shear response of different directions in the same material due to material crystallographic texture anisotropy. Shear bands are narrower in specimens in which the shear zone is aligned along the direction with a strong {0001} basal texture. Twinning was identified as an active mechanism to accommodate strains in the shear region in both orientations. This paper confirms the applicability of the CFSS design for the investigation of differences in the shear response of materials as a function of process-induced crystallographic texture. A detailed, systematic approach to quantifying shear band evolution by evaluating geometrically necessary dislocations (GND) associated with crystallographic anisotropy is presented. Finally, the results show that: i) line average GND density profiles, for Ti samples that possess a uniform equiaxed-grain structure, but with strong crystallographic anisotropy, exhibit significant differences in GND density close to the shear band center; ii) GND profiles decrease steadily away from the shear band as the plastic strain diminishes, in agreement with Ashby's theory of work hardening, where the higher GND density in the through-thickness (TT) orientation is a result of restricted < a > type slip in the shear band compared with in-plane (IP) samples; iii) the anisotropy in deformation response is derived from initial crystallographic texture of the materials, where GND density of < a > GNDs are higher adjacent to the shear band in the through-thickness sample oriented away from easy slip, but the density of < c+a > type GNDs are very similar in these two samples; and iv) the increase in grain average GND density was determined to have strong correlation to an increase in the Euler Φ angle of the grain average orientation, indicating an increased misorientation angle evolution.

36 MATERIALS SCIENCE↗
DOE OSTI2017

3D Microstructures for Materials and Damage Models

Many challenges exist with regard to understanding and representing complex physical processes involved with ductile damage and failure in polycrystalline metallic materials. Currently, the ability to accurately predict the macroscale ductile damage and failure response of metallic materials is lacking. Research at Los Alamos National Laboratory (LANL) is aimed at building a coupled experimental and computational methodology that supports the development of predictive damage capabilities by: capturing real distributions of microstructural features from real material and implementing them as digitally generated microstructures in damage model development; and, distilling structure-property information to link microstructural details to damage evolution under a multitude of loading states.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Modeling of additive manufacturing processes for metals: Challenges and opportunities

Here, with the technology being developed to manufacture metallic parts using increasingly advanced additive manufacturing processes, a new era has opened up for designing novel structural materials, from designing shapes and complex geometries to controlling the microstructure (alloy composition and morphology). The material properties used within specific structural components are also designable in order to meet specific performance requirements that are not imaginable with traditional metal forming and machining (subtractive) techniques.

36 MATERIALS SCIENCE↗