Search NASA⌕ Search

Engineering topics

Loarte, A. (ORCID:0000000195921117)

Publications and source records attributed to Loarte, A. (ORCID:0000000195921117).

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Quantification of locked mode instability triggered by a change in confinement

Abstract This work presents the first analysis of the disruptive locked mode (LM) triggered by the dynamics of a confinement change. It shows that, under certain conditions, the LM threshold during the transient is significantly lower than expected from steady states. We investigate the sensitivity to a controlled n = 1 error field (EF) activated prior to the L-H transition in the COMPASS tokamak, at q 95 ∼ 3, β N ∼ 1, and using EF coils on the high-field side of the vessel. A threshold for EF penetration subsequent to the L-H transition is identified, which shows no significant trend with density or applied torque, and is an apparent consequence of the reduced intrinsic rotation of the 2/1 mode during this transient phase. This finding challenges the assumption made in theoretical and empirical works that natural mode rotation can be predicted by global plasma parameters and urges against using any parametric EF penetration scaling derived from steady-state experiments to define the EF correction strategy in the entire discharge. Furthermore, even at EFs below the identified penetration threshold, disruptive locking of sawtooth-seeded 2/1 tearing modes is observed after about 30% of L-H transitions without external torque.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Ripple-induced neoclassical toroidal viscous torque in Augmented-First Plasma operation phase in ITER

Abstract A systematic calculation is performed on the ripple-induced neoclassical toroidal viscous (NTV) torque for new ITER scenarios designed for the Augmented-First Plasma (A-FP) operation phase with the full tungsten wall, where the plasma-wall gap is varied in view of mitigating the impact of tungsten wall-plasma interactions. The torque calculation includes drift kinetic response of the plasma thermal and energetic particles to the n = 18 ( n is the toroidal harmonic number) ripple field. For the plasma scenario with ~45 cm plasma-wall gap at the outboard mid-plane and considering the corrected ripple level of 0.17% by the ferritic steel inserts, the computed net NTV torque acting on the plasma column is in the sub-Nm level. However, with decreasing the plasma-wall gap, the computed net NTV torque can reach a level comparable to that produced by the neutral-beam momentum injection in ITER. Ripple correction by ferritic inserts reduces the net torque by a factor of 3.3 for all the three A-FP scenarios considered. The n ω d = l ω b (with ω d and ω b being the toroidal precession and bounce frequencies of trapped particles, respectively, and l an integer number) type of resonance-enhancement of the NTV torque, due to thermal particles, is found to be weak in ITER despite high- n of 18. The same also holds for the ITER 10 MA steady state scenario from the D-T operation phase, where the aforementioned resonance associated with fusion-born alphas is also included. The ripple-induced NTV torque is well below that produced by the resonant magnetic perturbation applied for controlling the type-I edge-localized mode in ITER.

ITER↗
DOE OSTI2024

Heuristic predictions of RMP configurations for ELM suppression in ITER burning plasmas and their impact on divertor performance

Abstract A subspace of resonant magnetic perturbation (RMP) configurations for edge localized mode (ELM) suppression is predicted for H-mode burning plasmas at 15 MA current and 5.3 T magnetic field in ITER. Perturbations to the core plasma can be reduced by a factor of 2 for equivalent edge stability proxies, while the perturbed plasma boundary geometry remains mostly resilient. The striated domain of perturbed field lines connecting from the main plasma (normalized poloidal flux < 1 ) to the divertor targets is found to be significantly larger than the expected heat load width in the absence of RMPs. This facilitates heat load spreading with peak values at an acceptable level below 10 MW m − 2 on the outer target already at moderate gas fueling and low Ne seeding for additional radiative dissipation of the 100 MW of power into the scrape-off layer (SOL). On the inner target, however, re-attachment is predicted away from the equilibrium strike point due to increased upstream heat flux, higher downstream temperature and less efficient impurity radiation.

3D plasma boundary modeling↗
DOE OSTI2024

Role of turbulent separatrix tangle in the improvement of the integrated pedestal and heat exhaust issue for stationary-operation tokamak fusion reactors

Abstract The magnetic separatrix surface is designed to provide the final and critical confinement to the hot stationary-operation core plasma in modern tokamak reactors in the absence of an external magnetic perturbation (MP) or transient magneto-hydrodynamic perturbation, while diverting the exhaust heat to divertor plates. All the stationary operational boundary plasma studies and reactor designs have been performed under this assumption. However, there has been a long-standing suspicion that a stationary-operation tokamak plasma even without external MPs or edge localized modes (ELMs) activities may not have a stable closed separatrix surface, especially near the magnetic X-point. Here, the first gyrokinetic numerical observation is reported that the divertor separatrix surface, due to homoclinic tangles caused by intrinsic electromagnetic turbulence, is not a stable closed surface in a stationary operation phase even without MPs or ELMs. Unlike the MP- or ELM-driven homoclinic tangles that could cause deleterious effects to core confinement or divertor plates, it is found that the micro-turbulence driven homoclinic tangles could connect the divertor plasma to the pedestal plasma in a constructive way by broadening the divertor heat-exhaust footprint and weakening the pedestal slope to the ELM-safe direction. Micro-turbulent homoclinic tangles can open a new research direction in understanding and controlling these two most troublesome and non-locally connected edge-plasma issues in a tokamak fusion reactor.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

L-H transition studies in tritium and deuterium–tritium campaigns at JET with Be wall and W divertor

The recent deuterium–tritium campaign in JET-ILW (DTE2) has provided a unique opportunity to study the isotope dependence of the L-H power threshold in an ITER-like wall environment (Be wall and W divertor). Here we present results from dedicated L-H transition experiments at JET-ILW, documenting the power threshold in tritium and deuterium–tritium plasmas, comparing them with the matching deuterium and hydrogen datasets. From earlier experiments in JET-ILW it is known that as plasma isotopic composition changes from deuterium, through varying deuterium/hydrogen concentrations, to pure hydrogen, the value of the line averaged density at which the threshold is minimum, ${\bar n_{{\text{e}},{\text{min}}}}$, increases, leading us to expect that ${\bar n_{{\text{e}},{\text{min}}}}$(T) < ${\bar n_{{\text{e}},{\text{min}}}}$(DT) < ${\bar n_{{\text{e}},{\text{min}}}}$(D) < ${\bar n_{{\text{e}},{\text{min}}}}$(H). The new power threshold data confirms these expectations in most cases, with the corresponding ordering of the minimum power thresholds. We present a comparison of this data to power threshold scalings, used for extrapolation to future devices such as ITER and DEMO.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Quasi-linear toroidal simulations of resonant magnetic perturbations in eight ITER H-mode scenarios

Abstract Both linear and quasi-linear aspects of the plasma response to the resonant magnetic perturbation (RMP) field are numerically investigated for various H-mode scenarios in ITER, covering the pre-fusion power operation and the fusion power operation phases. Linear response computations for eight ITER scenarios, with varying plasma current and toroidal magnetic field, reveal that the best coil current phasing for controlling the type-I edge localized modes (ELMs) scales roughly linearly with the edge safety factor. The coil phasing is defined as the relative toroidal phase of the coil currents between different rows, for a given toroidal harmonic. Quasi-linear initial value simulation, which is the focus of the present study, shows that application of the n = 3 ( n is the toroidal mode number) RMP field has a minimum side effect on the plasma core momentum confinement but potentially a large effect on the global particle transport. Generally, the RMP field with the best (worst) coil phasing for ELM control produces the strongest (weakest) effect on the plasma edge flow and the overall density. This robustly holds for all eight ITER scenarios. Consequently, in order to minimize the RMP induced side effects while achieving ELM control (suppression) in ITER, a compromise is necessary in choosing the coil current configuration.

Physics↗
DOE OSTI2022

Overview of the COMPASS results *

COMPASS addressed several physical processes that may explain the behaviour of important phenomena. This paper presents results related to the main fields of COMPASS research obtained in the recent two years, including studies of turbulence, L–H transition, plasma material interaction, runaway electron, and disruption physics: Tomographic reconstruction of the edge/SOL turbulence observed by a fast visible camera allowed to visualize turbulent structures without perturbing the plasma. Dependence of the power threshold on the X-point height was studied and related role of radial electric field in the edge/SOL plasma was identified. The effect of high-field-side error fields on the L–H transition was investigated in order to assess the influence of the central solenoid misalignment and the possibility to compensate these error fields by low-field-side coils. Results of fast measurements of electron temperature during ELMs show the ELM peak values at the divertor are around 80% of the initial temperature at the pedestal. Liquid metals were used for the first time as plasma facing material in ELMy H-mode in the tokamak divertor. Good power handling capability was observed for heat fluxes up to 12 MW m –2 and no direct droplet ejection was observed. Partial detachment regime was achieved by impurity seeding in the divertor. The evolution of the heat flux footprint at the outer target was studied. Runaway electrons were studied using new unique systems—impact calorimetry, carbon pellet injection technique, wide variety of magnetic perturbations. Radial feedback control was imposed on the beam. Forces during plasma disruptions were monitored by a number of new diagnostics for vacuum vessel (VV) motion in order to contribute to the scaling laws of sideways disruption forces for ITER. Current flows towards the divertor tiles, incl. possible short-circuiting through PFCs, were investigated during the VDE experiments. The results support ATEC model and improve understanding of disruption loads.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

L–H transition threshold studies in helium plasmas at JET

We present a study of the power threshold for L–H transitions (P LH ) in almost pure helium plasmas, obtained in recent experiments at JET with an ITER-like wall (Be wall and W divertor). The most notable new result is that the density at which P LH is minimum, $\bar{n}_{c,min}$, is considerably higher for helium than for deuterium and hydrogen plasmas. We discuss the possible implications for ITER in its pre-fusion operating power phase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Impact of suprathermal ions on neutron yield in the pre-DT phase of ITER operation

An assessment of neutron production during the pre-fusion power-operation (PFPO) phase has been carried out for a representative set of plasma scenarios predicted by the ITER Research Plan. A range of heating systems, namely neutral beam injection (NBI) (hydrogen), electron cyclotron resonance heating (ECRH), and ion cyclotron resonance heating (ICRH) are planned to be used for PFPO studies in helium, hydrogen, and mixed hydrogen–helium plasmas. Fast ions (protons and 3He) originating from NBI and ICRH systems can increase neutron production in PFPO plasmas by directly interacting with intrinsic Be impurities or through secondary processes, as also evidenced at JET. The generation of fast ions in ITER PFPO scenarios has been modelled using the ASTRA-NBI and TORIC-SSFPQL codes. A significant impact of the synergy between hydrogen NBI and hydrogen-minority ICRH on neutron production in helium plasmas is reported. In addition, the stability of the toroidicity-induced Alfvén eigenmodes (TAE) is analyzed for PFPO plasmas with a high pressure of suprathermal ions and a weak reversed shear. The possible impact of sawtooth oscillations and TAEs on neutron production is discussed, based on a linear stability analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗