Search NASA⌕ Search

Engineering topics

Lombard, C. K.

Publications and source records attributed to Lombard, C. K..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Navier-Stokes simulation of 3-D hypersonic equilibrium air flow

A computationally efficient three-dimensional conservative supracharacteristic Navier-Stokes method has been extended to simulate complex external chemically reacting flows of hypersonic reentry vehicles at angle-of-attack. Numerical simulation results of the flow around a sphere-cone-cone-flare reentry vehicle at 10 deg angle-of-attack are presented, in addition to the results of a well-validated two-dimensional code with which the 0-deg axisymmetric flow has been computed. A method for obtaining compositions of species in equilibrium ionized air is proposed.

Nagaraj, N.↗
NASA NTRS1988

FASTWO - A 2-D interactive algebraic grid generator

This paper presents a very simple and effective computational procedure, FASTWO, for generating patched composite finite difference grids in 2-D for any geometry. Major components of the interactive graphics based method that is closely akin to and borrows many tools from transfinite interpolation are highlighted. Several grids produced by FASTWO are shown to illustrate its powerful capability. Comments about extending the methodology to 3-D are also given.

Luh, Raymond Ching-Chung↗
NASA NTRS1988

CSCM Navier-Stokes thermal/aerodynamic analysis of hypersonic nozzle flows with slot injection and wall cooling

The Conservative Supra-Characteristic Method (CSCM) Navier-Stokes solver is applied to ascertain the problems inherent in the design of a nominal Mach 14 nozzle for NASA-Ames' 3.5-ft Hypersonic Wind Tunnel; attention is given to the effects of boundary layer cooling systems on the aerodynamic redesign of the nozzle throat region. Complete nozzle flowfields are calculated with and without slot injection of either hot or cold fluid into the boundary layer just upstream of the throat, as well as with alternatively adiabatic and cold walls. The CSCM method is capable of resolving subtle differences in the flows.

Codding, William H.↗
NASA NTRS1988

Extensions of the CSCM methodology for nonequilibrium reacting gas flows

The paper describes the extension of the CSCM flux difference splitting to produce conservative unconditionally stable implicit upwind methods for the extended equation set. The CSCM-S single data level relaxation algorithm is argued to be particularly advantageous for efficiently solving the set of equations. Attention is given to issues of alternative state variable representations and to complementary thermodynamic relations that parameterize and need to be effectively coupled with the solution procedure for the partial differential equations. Within the framework of iteration, consideration is given to more efficient approximate solution procedures than the full block coupled LU decomposition. Results of early numerical experiments are given to illustrate the developments.

Lombard, C. K.↗
NASA NTRS1987

Navier-Stokes simulation of real gas flows in nozzles

Air flow in a hypersonic nozzle causes real gas effects due to reaction among the species constituting air. Such reactions may be in chemical equilibrium or in chemical nonequilibrium. Here using the CSCM upwind scheme for the compressible Navier-Stokes equations, the real gas flowfield in an arcjet nozzle is computed for both the equilibrium case and the nonequilibrium case. A hypersonic nozzle flow arising from a pebble bed heated plenum is also computed for the equilibrium situation. Between the equilibrium cases, the chemistry is treated by two different schemes and comments are made as to computational complexity. For the nonequilibrium case, a full set of seventeen reactions and full implicit coupling of five species with gasdynamics is employed to compute the flowfield. For all cases considered here the gas is assumed to be a calorically imperfect mixture of ideal gases in thermal equilibrium.

Nagaraj, N.↗
NASA NTRS1987

Application of the CSCM method to the design of wedge cavities

This paper describes the application of the conservative supra characteristic method (CSCM) to predict the flow around two-dimensional slot injection cooled cavities in hypersonic flow. Seven different numerical solutions are presented that model three different experimental designs. The calculations manifest outer flow conditions including the effects of nozzle/lip geometry, angle of attack, nozzle inlet conditions, boundary and shear layer growth and turbulance on the surrounding flow. The calculations were performed for analysis prior to wind tunnel testing for sensitivity studies early in the design process. Qualitative and quantitative understanding of the flows for each of the cavity designs and design recommendations are provided. The present paper demonstrates the ability of numerical schemes, such as the CSCM method, to play a significant role in the design process.

Venkatapathy, Ethiraj↗
NASA NTRS1987

Aerodynamic design modification of a hypersonic wind tunnel nozzle by CSCM with high order accuracy

An improved version of the CSCM implicit Navier-Stokes solver with a flexible data structure has been applied, in conjunction with a sophisticated patched grid system, to the aerodynamic analysis of hypersonic axisymmetric contoured nozzles of the NASA-Ames 3.5-foot hypersonic wind tunnel. The results obtained are found to be in good agreement with experiment. Based on the analysis, a newly designed throat contour for the Mach 14 nozzle has been recommended.

Yang, J. Y.↗
NASA NTRS1987

Numerical simulation of compressible flow around complex two-dimensional cavities

Compressible viscous flow around two-dimensional cavities, that model the midplane flow in and around an airborne telescope cavity, are obtained through numerical simulation. Numerical solutions using the patched grid CSCM scheme for compressible, unsteady flow are presented for the cavities, with and without blowing. The time evolving solutions show interesting flow features. Relevant results for a limited number of problems presented here show the unsteady nature of the flow and its dependence on various parameters such as Reynolds number, the wall conditions, etc. The voluminous data of time evolving flow field solutions are analyzed through movies of the velocity vectors, and contours of other flow variables.

Venkatapathy, Ethiraj↗
NASA NTRS1987

Simplified algebraic grid generation in patched mesh systems

Some computational tools and techniques are described that are integrated into a simplified algebraic grid generation procedure. Major steps of such a procedure are also outlined. Grids generated via this approach for several complex geometries are shown to demonstrate the potential for wide application.

Luh, Raymond Ching-Chung↗
NASA NTRS1987

CSCM methodology for slot injection cooled cavity flow design in a high enthalpic stream

The CSCM method for the compressible Navier-Stokes equations is applied to study design factors in a slot injection cooled cavity flow in the side of a 2-D wedge body in a high enthalpy free stream. The flow geometry is being designed and will be tested in an arc jet tunnel at NASA-Ames Research Center. Objectives of the design are to provide adequate thermal protection for and minimize aero-optical distortion in the path above a window located in the bottom of the cavity. Among design issues, are the geometry of and flow conditions in the expanding section of the supersonic slot injection nozzle. Here, for straight walled nozzles, two geometries are considered for the upper nozzle lip between the hot, high speed outer flow and the colder, denser cooling flow. The two lip geometries - thick, square and thin, wedge - as the result of associated widely differing base/wake flows also exhibit different and interesting viscous-inviscid flow structures near the ramp termination to the cavity. For the thin lip case, the consequences on flow quality of off design nozzle conditions relative to matching pressure with the outer flow are explored.

Bardina, Jorge↗
NASA NTRS1987

Three dimensional hypersonic flow simulations with the CSCM implicit upwind Navier-Stokes method

The Bardina and Lombard (1985) three-dimensional CSCM Navier-Stokes method is presently extended to the simulation of complex hypersonic reentry vehicle external flows at angle of attack. The robust stability of the method derives from the combination of conservative implicit upwind flux difference splitting with a three-dimensional diagonally-dominant approximate factorization and relaxation scheme and characteristic-based implicit boundary approximations. The method's efficiency derives from an implicit symmetric Gauss-Seidel 'method of planes' relaxation scheme with alternating directional space marching sweeps along the flow coordinate direction.

Bardina, Jorge↗
NASA NTRS1986

An efficient adaptive patched grid gas dynamic solver for complex flows

The patched mesh CSCM flow solver is used with a fast adaptive grid technique to compute complex two dimensional and axisymmetric, inviscid and viscous flows accurately and efficiently. The patched grid technique allows the user to generate the initial grid around complex regions with minimal effort. The adaptive grid strategy permits the grid points to adjust to the solution in accordance with the flow structure and user specified grid constraints and thus improve the accuracy of the solution. Solutions to challenging flow problems are obtained with adapted grids and the numerical examples and the results presented here show clearly the effectiveness of the adaptive grid solution strategy to obtain highly accurate numerical solutions with minimal human effort and computational resources.

Venkatapathy, E.↗
NASA NTRS1986

Numerical simulation of backward step and jet exhaust flows

Preparatory to a continuing study of efficient, high resolution flow structure capture on patched mesh systems, turbulent flowfield solutions for a tactical missile base flow problem are computed on two first level composite grids of differing topologies. One mesh is of the wraparound character and the other is a step mesh on the Cartesian topology. A simplified Baldwin-Lomax algebraic eddy viscosity model is applied in the wake region. Results for the two meshes are compared with each other and with other computations reported in the literature. The totality of results suggest both mesh topology and resolution are important factors in the accuracy of predictive results as well as turbulence modeling. Related to interests in high altitude laminar flows bluff bodies such as the AOTV, the paper also presents results from a solution from laminar flow over a backward facing step and makes comparison with the available classical experiment of Chapman, et al.

Lombard, C. K.↗
NASA NTRS1986

Computation of nonstationary strong shock diffraction by curved surfaces

A two-dimensional, high resolution shock-capturing algorithm was used on a supercomputer to solve Eulerian gasdynamic equations in order to simulate nonstationary strong shock diffraction by a circular arc model in a shock tube. The hypersonic Mach shock wave was assumed to arrive at a high angle of incidence, and attention was given to the effect of varying values of the ratio of specific heats on the shock diffraction process. Details of the conservation equations of the numerical algorithm, written in curvilinear coordinates, are provided, and model output is illustrated with the results generated for a Mach shock encountering a 15 deg circular arc. The sample graphics include isopycnics, a shock surface density profile, and pressure and Mach number contours.

Yang, J. Y.↗
NASA NTRS1985

Numerical simulation of transient inviscid gas flows in a shock tube

Time-dependent upwind high resolution schemes for solving the Euler equations were developed and applied to simulate 1-D and 2-D transient inviscid gas flows in a shock tube. Using obstacles of different geometries, a series of calculations were carried out to investigate the transient complex shock-wave diffraction phenomena. Shock-wave and objects interactions with shock Mach-number Ms ranging from 2 to 20 were considered. Comparison with analytical and available experimental results indicate good agreement. Display of detailed flow structures including multiple Mach shocks, slip surfaces, and vortex are also given.

Yang, J. Y.↗
NASA NTRS1985

Three dimensional CSCM method for the compressible Navier-Stokes equations with application to a multi-nozzle exhaust flowfield

The effective design of three-dimensional flow systems such as a clustered multinozzle shrouded exhaust system requires detailed analysis of the internal flowfield. It is pointed out that new numerical techniques on the most modern vector computers are making these analyses practicable. In this paper, the upwind differenced implicit conservative supracharacteristics method (CSCM) for three-dimensional viscous flow is presented. The new method is an implicit 'method of planes' symmetric Gauss-Seidel relaxation scheme. The data is conveniently stored on successive planes along the streamwise coordinate, and the system of equations is solved twice in each successive plane of the streamwise coordinate. The developed new three-dimensional compressible Navier-Stokes algorithm combines the best features of the storage and computationally efficient space marching procedures with the generality of time dependent techniques to solve flows with elliptic and streamwise separated flows.

Bardina, J.↗
NASA NTRS1985

Flow structure capturing on overset patched meshes

The present paper describes the application of a simple, robust stable implicit approach to solutions of the conservative equations of gasdynamics on either composite or overset meshes to capture flow structures such as shocks with high resolution in complex geometric domains. Without requiring special flux conservative operators, but rather, interpolating conservative variable data at mesh boundaries, the well posed upwind method provides accurate and oscillation free solutions, even when shocks cross the interior patch boundaries. In three problems with flow complexities that require grid refinement, the paper demonstrates the capability to conveniently carry out for gasdynamics the adaptive refined meshing strategy in overset patches proposed by Berger and Oliger (1984), and it extends this technique to rapidly convergent implicit methods for the Euler and Navier-Stokes equations. The numerical experiments show concretely, in a realistic aerodynamic problem, the savings in mesh points (about an order of magnitude here in two dimensions) for similar accuracy that flow structure aligned adaptive patched meshing affords compared to uniform grid refinement.

Venkatapathy, E.↗