Search NASA⌕ Search

Engineering topics

Lopez-Ruiz, Juan A.

Publications and source records attributed to Lopez-Ruiz, Juan A..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Electrochemical Oxidation of Seawater for Renewable Energy Generation and Storage in Coastal Areas

In this work, we demonstrated how the Clean Sustainable Electrochemical Treatment process can be used to process seawater while simultaneously generating molecular hydrogen. The specific goal of this project is to (1) demonstrate selective removal of chemical oxygen demand over the oxygen and chlorine evolution reactions, (2) optimize electrode composition to improve electrochemical performance, and (3) demonstrate long-term (>100 h) stability experiments.

08 HYDROGEN↗
DOE OSTI2024

Pilot microbial electrolysis cell closes the hydrogen loop for hydrothermal wet waste conversion to jet fuel

The global shift toward net-zero emissions necessitates resource recovery from wet waste. In this study, we demonstrate the first feasibility of combining pilot-scale microbial electrolytic cells (MECs) with hydrothermal liquefaction (HTL) for simultaneous post-hydrothermal liquefaction wastewater (PHW) treatment and efficient hydrogen (H₂) production to meet biocrude upgrading requirements. Long-term single reactor operation revealed that fixed anode potential enabled rapid startup, and low catholyte pH and high salinity were effective in suppression of cathodic methanogenesis and acetogenesis – resulting in high current density of 16.6 A m –2 and 9.3 A m –2 when feeding synthetic wastewater and PHW respectively. Additionally, the anode biofilm exhibited spatial variations in response to local environmental conditions. In conclusion, onsite parallel or serial operations of multiple MECs showed good performance using actual PHW with a record-high H 2 production rate of 0.5 L L R day –1 for MEC over 10 liters scale, and the optimal chemical oxygen demand (COD)-to-H 2 yield reached 0.127 kg-H 2 per kg-COD, supporting a self-sufficient, closed-loop upgrade to jet fuel.

08 HYDROGEN↗
DOE OSTI2024

Catalytic Conversion of Biogenic and Synthetic Polymers into Carbon-Negative and -Neutral Chemicals and Fuels

We investigated a technology that enables the distributed decomposition of biogenic (lignin, cellulose) and synthetic (plastic) polymers into renewable or low-carbon-emission chemicals and fuel intermediates that can substitute fossil hydrocarbons for energy, chemical, and fuel production. The specific goal of this project is to (1) selectively convert biogenic polymers such as lignin and synthetic polymers such as polyethylene into hydrocarbons via electrocatalytic and thermocatalytic processes, and (2) optimize (electro)catalyst composition and reaction conditions to mitigate deactivation and control product selectivity.

09 BIOMASS FUELS↗
DOE OSTI2024

Methane Pyrolysis for CO2-free H2 and Carbon Nanomaterials - CRADA 576 (Final Report)

In this CRADA project we continued to develop the Pacific Northwest National Laboratory (PNNL) patent-pending Regenerable Catalytic Pyrolysis (ReCaP) process technology for producing CO 2 -free hydrogen (H 2 ) from inexpensive and domestically-abundant natural gas (NG), while simultaneously reducing H 2 ’s net production cost to $\$$1.0/kg through the sale of valuable crystalline solid carbon co-product. Producing clean hydrogen at this price is a DOE Hydrogen Energy Earthshot goal. This effort builds on our prior catalyst and processing advances made thermocatalytic decomposition of methane (TCD). The additional scope performed here accelerated the commercial deployment of TCD for CO 2 -free H 2 and valuable solid carbon nanotubes (CNT) co-product, by i) scaling up the production of CNT co-product using a fluidized bed reactor (25 g catalyst scale versus the 1 g catalyst scale demonstrated prior), ii) producing approximately 1 kg of CNT byproduct, produced via multiple cycles of TCD, carbon-catalyst separation, and catalyst re-synthesis, to enable the production of sufficient quantities of solid carbon so as to explore its market potential, iii) understanding the quality of the co-product CNTs, produced at larger scale, using advanced characterization, and iv) beginning to explore multiple promising high volume carbon product applications (e.g., aluminum and polymer composites, steel additive, and cement reinforcement applications). We are in discussions with Department of Energy and potential commercial partners to continue funding of this effort with the goal to facilitate eventual commercial deployment.

08 HYDROGEN↗
DOE OSTI2023

Low-Temperature Electrochemical Wastewater Oxidation

Here, we demonstrated the Clean Sustainable Electrochemical Treatment (CleanSET) process that enables the distributed clean-up of biomass-derived wastewater while simultaneously generating hydrogen (H 2 ). The specific goal of this project is to 1) demonstrate the selective removal of chemical oxygen demand (COD), total carbon (TC), and total nitrogen (TN) of different wastewaters, 2) optimize the electrode composition to improve electrochemical performance, and 3) perform a high-level techno-economic analysis to obtain levelized costs of disposal (LCOD) .

08 HYDROGEN↗
DOE OSTI2023

Customization for Current Market Applications of the Carbon Nanotubes Produced by PNNL’s Regenerable Catalytic Pyrolysis (ReCaP) for Scaled Hydrogen Production

Here, we demonstrated the Regenerative Catalytic Pyrolysis (ReCaP) process that generates carbon dioxide-free hydrogen (CO 2 -free H 2 ) from inexpensive and domestically abundant natural gas (NG), while simultaneously producing H 2 at net production cost of $1.0/kg through the sale of valuable carbon nanotube (CNT) co-product. The specific goal of this project is to 1) scale up the production of CNT, 2) correlate the properties of the CNT with the reaction conditions, 3) perform a techno-economic analysis to obtain minimum selling price of H 2 and CNT, and 4) identify industrial partners interested in the CNT co-product.

03 NATURAL GAS↗
DOE OSTI2023

Molecular Transformation and Metabolic Insights of Microbial Electrolysis Treatment and Valorization of Post-hydrothermal Liquefaction Wastewater

Hydrothermal liquefaction (HTL) presents a promising approach for the conversion of wet waste into biocrude and biofuels. However, the post-hydrothermal liquefaction wastewater (PHW) poses significant challenges for treatment and valorization due to its high concentration and complex nature. In this study, we investigated the conversion pathways of major organic contaminants within the microbial electrolytic treatment of PHW from food waste HTL. To achieve this, we employed high-performance liquid chromatography (HPLC) and 2D nuclear magnetic resonance (NMR). Our findings demonstrate volatile fatty acids (VFAs) and monohydric and polyhydric alcohols were effectively transformed through the synergistic metabolism of fermentative and electroactive bacteria, which led to over 70% COD removal of the recalcitrant compounds and a record high H2 production rate (1.62 L L -1 d -1 ). We also employed the liquid-state 15N NMR on wastewater samples for the first time and revealed that the nitrogen-containing heteroaromatics were persistent to microbial electrochemical treatment. By integrating the chemical profiles with bioanode community profiles, we constructed a metabolic network that provides insights for enhancing treatment efficiency and facilitating resource recovery.

08 HYDROGEN↗
DOE OSTI2023

Scale-up and techno-economic analysis of microbial electrolysis cells for hydrogen production from wastewater

Microbial electrolysis cells (MECs) have demonstrated high-rate H 2 production while concurrently treating wastewater, but the transition in scale from laboratory research to systems that can be practically applied has encountered challenges. It has been more than a decade since the first pilot-scale MEC was reported, and in recent years, many attempts have been made to overcome the barriers and move the technology to the market. This study provided a detailed analysis of MEC scale-up efforts and summarized the key factors that should be considered to further develop the technology. We compared the major scale-up configurations and systematically evaluated their performance from both technical and economic perspectives. We characterized how system scale-up impacts the key performance metrics such as volumetric current density and H 2 production rate, and we proposed methods to evaluate and optimize system design and fabrication. In addition, preliminary techno-economic analysis indicates that MECs can be profitable in many different market scenarios with or without subsidies. Here, we also provide perspectives on future development needed to transition MEC technology to the marketplace.

42 ENGINEERING↗
DOE OSTI2023

Using earth abundant materials for long duration energy storage: electro-chemical and thermo-chemical cycling of bicarbonate/formate

Using hydrogen to store energy in chemical bonds is a key component of the global strategy to achieving a sustainable future and ameliorating climate change. The challenges associated with handling molecular hydrogen can be solved by using liquid hydrogen carriers. In this perspective, we discuss the concept of bicarbonate–formate cycle, where aqueous solutions of formate ions (HCO 2 – ) are used as hydrogen and energy carriers. Such solutions are composed by earth abundant elements and, in contrast to common liquid organic carriers, are non-flammable, and readily convert to the oxide forms (HCO 3 – ) under reaction with water to release hydrogen, or electrons, at moderate temperatures. We discuss thermodynamic aspects of the bicarbonate–formate cycle and show how it offers the opportunity of combining electrochemical and thermochemical operations, as well as of coupling CO 2 capture with energy/hydrogen storage. We emphasize the potential role of electrochemistry in the generation of formate and in the release of energy in the form of electricity. At present, more information on both the fundamental and systems level, is needed to identify the feasible scenarios for using formate/bicarbonate salts for hydrogen/energy storage. It is likely, however, that several strategies, including hybrid electrochemical–thermochemical approaches, will suit different applications. It is also clear that more integration between the disciplines of electrochemistry and heterogeneous catalysis is needed to overcome the challenges for advancing the HCO 3 – –HCO 2 – system as a feasible green alternative for storing and transporting energy.

08 HYDROGEN↗
DOE OSTI2022

Methane Catalytic Pyrolysis by Microwave and Thermal Heating over Carbon Nanotube-Supported Catalysts: Productivity, Kinetics, and Energy Efficiency

Methane catalytic pyrolysis, which is the reaction to produce hydrogen and carbon without emitting CO 2 , represents an approach for decarbonization using natural gas as an energy resource. In this work, the endothermic pyrolysis reaction was carried out under two heating scenarios: convective thermal heating and microwave-driven irradiative heating. The pyrolysis reaction was conducted at 550-600 °C over carbon nanotube-supported Ni-Pd and Ni-Cu catalysts. On both catalysts, an enhanced methane conversion rate was observed under microwave irradiation. The enhanced catalytic activity was hypothetically caused by the presence of free electrons in the carbon atoms within CNT that enabled the CNT support to absorb microwave energy effectively and to be heated efficiently by microwave. The microwave catalytic pyrolysis has shown improvement in kinetics, where the apparent activation energy dropped from 45.5 kJ/mol under conventional convective heating to 24.8 kJ/mol under microwave irradiation. When the methane conversion rate is increased by 37 %, the microwave power consumption only changed by 10.8 %. The research demonstrated the potential of transforming natural gas to clean hydrogen and value-added carbon in a more energy-efficient way. Process simulation and techno-economic analysis showed that potentially hydrogen minimum selling price of about $1 /kg H 2 could be achieved.

03 NATURAL GAS↗
DOE OSTI2022

Electrocatalytic decarboxylation of carboxylic acids over RuO 2 and Pt nanoparticles

Here, we report electrocatalytic decarboxylation (ECDX) of valeric acid into paraffins, olefins, and alcohols via (non-)Kolbe electrolysis on electrodes with RuO 2 and Pt nanoparticles (NPs) as a greener alternative to thermocatalytic decarboxylation. The turnover frequency of ECDX increases, while the specific activity peaks as RuO 2 NP size increases. These opposing trends make the particle size of ∼ 12 nm the optimum size for ECDX on RuO 2 . Bulk Pt was active for ECDX, while Pt NPs were only active for the oxygen evolution reaction under our conditions. ECDX current efficiency remained constant in the studied potential range on RuO 2 NPs. Esterification was the favored reaction at 2.5 V vs. RHE; however, Kolbe electrolysis was the favored reaction at the expense of the esterification at 4.5 V vs. RHE. This work highlights the performance of nanostructured materials as an alternative to bulk materials as anodes for oxidative upgrading of carboxylic acids.

Kolbe electrolysis↗
DOE OSTI2021

The Surge of Metal–Organic-Framework (MOFs)-Based Electrodes as Key Elements in Electrochemically Driven Processes for the Environment

Metal–organic-frameworks (MOFs) are emerging materials used in the environmental electrochemistry community for Faradaic and non-Faradaic water remediation technologies. It has been concluded that MOF-based materials show improvement in performance compared to traditional (non-)faradaic materials. In particular, this review outlines MOF synthesis and their application in the fields of electron- and photoelectron-Fenton degradation reactions, photoelectrocatalytic degradations, and capacitive deionization physical separations. This work overviews the main electrode materials used for the different environmental remediation processes, discusses the main performance enhancements achieved via the utilization of MOFs compared to traditional materials, and provides perspective and insights for the further development of the utilization of MOF-derived materials in electrified water treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Catalytic decomposition of methane into hydrogen and high-value carbons: combined experimental and DFT computational study

Thermocatalytic decomposition (TCD) of methane can produce hydrogen and valuable nanocarbon co-products with low to near-zero CO2 emission. In this study, a series of Pd promoted Ni catalysts, prepared with various Ni/Pd ratios on a CNT support, were evaluated for methane TCD performance. Characterization and calculations using density functional theory (DFT) were carried out to elucidate the activity–structure relationship and growth mechanism of carbon nanomaterials. It was found that the methane conversion and stability of the catalysts were highly dependent on the Ni/Pd ratio and reaction temperature. DFT calculations revealed that the diffusion of carbon in the metal sublayer required for CNT growth was more favorable in the Ni–Pd alloy lattice suggesting that the buildup of carbon in the metal alloy sublayer facilitated the formation of CNTs and CNFs. A cyclic reaction–regeneration process for self-sustained TCD was experimentally demonstrated. In each cycle, a portion of the separated CNT product was used to re-synthesize the Ni–Pd/CNT catalyst for use in the next reaction cycle. After five cycles of operation, the CH4 conversion, morphology and crystallinity of the carbon product remained unchanged.

Wang, I-Wen↗
DOE OSTI2021

Structure sensitivity and its effect on methane turnover and carbon co-product selectivity in thermocatalytic decomposition of methane over supported Ni catalysts

We explore how thermocatalytic decomposition of methane (TCD) is a promising approach for producing CO 2 -free hydrogen and solid carbon co-product. In this study, a series of Al 2 O 3 - and MgAl 2 O 4 -based Ni catalysts, prepared with varying synthesis and pretreatment methods, were evaluated for methane TCD performance at 650°C and characterized before and after reaction to elucidate activity-structure relationships. We found that methane TCD turnover increases with Ni particle size. Further, large Ni particle sizes (i.e., >20 nm) are selective toward the formation of carbon nanotubes (CNTs), while small Ni particle sizes (i.e., <10 nm) are selective toward the formation of graphitic carbon layers. The formation of graphitic carbon layers block access to Ni active sites, thus rendering the catalyst inactive more quickly than when CNTs are produced. Additionally, the catalyst deactivation observed with time-on-stream is due to the fragmentation of Ni particles into smaller Ni particles followed by their encapsulation with graphitic carbon layers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Electrocatalytic Hydrogenation of Biomass-Derived Organics: A review

Sustainable energy generation calls for a shift away from centralized, high-temperature, energy-intensive processes to decentralized, low-temperature conversions that can be powered by electricity produced from renewable sources. Electrocatalytic conversion of biomass-derived feedstocks would allow carbon recycling of distributed, energy-poor resources in the absence of sinks and sources of high-grade heat. Selective, efficient electrocatalysts that operate at low temperatures are needed for electrocatalytic hydrogenation (ECH) to upgrade the feedstocks. For effective generation of energy-dense chemicals and fuels, two design criteria must be met: (i) a high H:C ratio via ECH to allow for high-quality fuels and blends, and (ii) a lower O:C ratio in the target molecules via electrochemical decarboxylation/deoxygenation to improve the stability of fuels and chemicals. The goal of this review is to determine whether the following questions have been sufficiently answered in open literature, and if not, what additional information is required: (1) What organic functionalities are accessible for electrocatalytic hydrogenation under a set of reaction conditions? How do substitutions and functionalities impact the activity and selectivity of ECH? (2) What material properties cause an electrocatalyst to be active for ECH? Can general trends in ECH be formulated based on the type of electrocatalyst? (3) What is the impact of reaction (electrolyte concentration, pH, operating potential) and reactor type conditions?

Catalysts, redox reactions, hydrocarbons, Aromatic↗
DOE OSTI2020

Electrocatalytic Valorization into H2 and Hydrocarbons of an Aqueous Stream Derived from Hydrothermal Liquefaction

Electrocatalytic oxidation is an attractive process for valorizing the carbon and removal of nitrogen present in the aqueous waste streams at ambient conditions. Here, we evaluated the electrocatalytic oxidation as a function of applied potential over a commercial Pt electrode of aqueous waste stream generated via hydrothermal liquefaction. We validated the conversion of quantifiable carbon (e.g., carboxylic acids, alpha hydroxyacids, alcohols, ketones, amides) and unquantifiable carbon as well as nitrogen removal. The unquantifiable carbon was valorized to quantifiable short chain organic molecules (e.g., acetic). Model studies showed that carboxylic acids, alcohol and ketones converted following (non-) Kolbe chemistry. Amides and alpha hydroxyacids formed carboxylic acids that subsequently converted via (non-) Kolbe chemistry. Ammonia was oxidized into N2. The reaction rate varied for each molecule family with carboxylic acids and ammonia having the highest reaction rates. The main reaction products from the electrocatalytic oxidation at the anode were volatile, short chain hydrocarbons (i.e., olefins, paraffins) and CO generated via Kolbe chemistry, while H2 was generated at the cathode. The parallel denitrification, valorization of carbon, and H2 generation of the aqueous waste can replace and simplify the current unit operations used in a commercial hydrothermal liquefaction process. The high operation potential required to drive the electrocatalytic reaction is responsible for high operation costs; however, they can be either partially subsidized with sale of excess H2 at the current DOE goal of $2/kg H2. Thus, the present work shows how electrocatalytic oxidation can be used to valorize aqueous waste streams into volatile hydrocarbons and H2.

Electrocatalytic oxidation, Aqueous waste valoriza↗