Search NASA⌕ Search

Engineering topics

Lorber, Peter F.

Publications and source records attributed to Lorber, Peter F..

11 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Dynamic Stall Suppression Using Combustion-Powered Actuation (COMPACT)

Retreating blade stall is a well-known phenomenon that limits rotorcraft speed, maneuverability, and efficiency. Airfoil dynamic stall is a simpler problem, which demonstrates many of the same flow phenomena. Combustion Powered Actuation (COMPACT) is an active flow control technology, which at the outset of this work, had been shown to mitigate static and dynamic stall at low Mach numbers. The attributes of this technology suggested strong potential for success at higher Mach numbers, but such experiments had never been conducted. The work detailed in this report documents a 3-year effort focused on assessing the effectiveness of COMPACT for dynamic stall suppression at freestream conditions up to Mach 0.5. The work done has focused on implementing COMPACT on a high-lift rotorcraft airfoil: the VR-12. This selection was made in order to ensure that any measured benefits are over and above the capabilities of state-of-the-art high-lift rotorcraft airfoils. The detailed Computational Fluid Dynamics (CFD) simulations, wind-tunnel experiments, and system-level modeling conducted have shown the following: (1) COMPACT, in its current state of development, is capable of reducing the adverse effects of deep dynamic stall at Mach numbers up to 0.4; (2) The two-dimensional (2D) CFD results trend well compared to the experiments; and (3) Implementation of the CFD results into a system-level model suggest that significant rotor-level benefits are possible.

Matalanis, Claude G.↗
NASA NTRS1992

Unsteady separation experiments on 2-D airfoils, 3-D wings, and model helicopter rotors

Information on unsteady separation and dynamic stall is being obtained from two experimental programs that have been underway at United Technologies Research Center since 1984. The first program is designed to obtain detailed surface pressure and boundary layer condition information during high amplitude pitching oscillations of a large (17.3 in. chord) model wing in a wind tunnel. The second program involves the construction and testing of a pressure-instrumented model helicopter rotor. This presentation describes some of the results of these experiments, and in particular compares the detailed dynamic stall inception information obtained from the oscillating wing with the unsteady separation and reverse flow results measured on the retreating blade side of the model rotor during wind tunnel testing.

Lorber, Peter F.↗
NASA NTRS1992

Unsteady transition measurements on a pitching three-dimensional wing

Boundary layer transition measurements were made during an experimental study of the aerodynamics of a rectangular wing undergoing unsteady pitching motions. The wing was tested at chordwise Mach numbers between 0.2 and 0.6, at sweep angles of 0, 15, and 30 deg, and for steady state, sinusoidal, and constant pitch rate motions. The model was scaled to represent a full size helicopter rotor blade, with chord Reynolds numbers between 2 and 6 x 10(exp 6). Sixteen surface hot-film gages were located along three spanwise stations: 0.08, 0.27, and 0.70 chords from the wing tip. Qualitative heat transfer information was obtained to identify the unsteady motion of the point of transition to turbulence. In combination with simultaneous measurements of the unsteady surface pressure distributions, the results illustrate the effects of compressibility, sweep, pitch rate, and proximity to the wing tip on the transition and relaminarization locations.

Lorber, Peter F.↗
NASA NTRS1992

Prediction of BVI noise patterns and correlation with wake interaction locations

High resolution fluctuating airloads data were acquired during a test of a contemporary design United Technologies model rotor in the Duits-Nederlandse Windtunnel (DNW). The airloads are used as input to the noise prediction program WOPWOP, in order to predict the blade-vortex interaction (BVI) noise field on a large plane below the rotor. Trends of predicted advancing and retreating side BVI noise levels and directionality as functions of flight condition are presented. The measured airloads have been analyzed to determine the BVI locations on the blade surface, and are used to interpret the predicted BVI noise radiation patterns. Predicted BVI locations are obtained using the free wake model in CAMRAD/JA, the UTRC Generalized Forward Flight Distorted Wake Model, and the UTRC FREEWAKE analysis. These predicted BVI locations are compared with those obtained from the measured pressure data.

Marcolini, Michael A.↗
NASA NTRS1991

Incipient torsional stall flutter aerodynamic experiments on a swept three-dimensional wing

The aerodynamics of small amplitude pitching motions near stall have been studied experimentally in order to improve understanding of the torsional stall flutter problem for propeller blades. A model wing was oscillated in pitch at several small amplitudes over a wide and representative range of conditions. Unsteady surface pressures were measured and integrated to determine the aerodynamic damping at five spanwise stations. Strong negative damping was found for motions centered near static stall for all studied reduced frequencies, Mach numbers, and sweep angles. The 30-deg sweptback configuration was found to become negatively damped over the entire span nearly simultaneously, while the unswept model exhibited local regions of negative damping that moved toward the wing tip as the mean angle of attack was increased.

Lorber, Peter F.↗
NASA NTRS1990

An unsteady helicopter rotor-fuselage aerodynamic interaction analysis

A computational method has been developed to treat the unsteady aerodynamic interaction between a helicopter rotor, wake, and fuselage. Two existing codes, a lifting line-prescribed wake rotor analysis and a source panel fuselage analysis, were modified and coupled to allow prediction of unsteady fuselage pressures and airloads. A prescribed displacement technique was developed to position the rotor wake about the fuselage. Also coupled into the method were optional blade dynamics or rigid blade performance analyses to set the rotor operating conditions. Sensitivity studies were performed to determine the influence of the wake and fuselage geometry on the computational results. Solutions were computed for an ellipsoidal fuselage and a four bladed rotor at several advance ratios, using both the classical helix and the generalized distorted wake model. Results are presented that describe the induced velocities, pressures, and airloads on the fuselage and the induced velocities and bound circulation at the rotor. The ability to treat arbitrary geometries was demonstrated using a simulated helicopter fuselage. Initial computations were made to simulate the geometry of an experimental rotor-fuselage interaction study performed at the Georgia Institute of Technology.

Lorber, Peter F.↗
NASA NTRS1990

Aerodynamic and acoustic test of a United Technologies model scale rotor at DNW

The UTC model scale rotors, the DNW wind tunnel, the AFDD rotary wing test stand, the UTRC and AFDD aerodynamic and acoustic data acquisition systems, and the scope of test matrices are discussed and an introduction to the test results is provided. It is pointed out that a comprehensive aero/acoustic database of several configurations of the UTC scaled model rotor has been created. The data is expected to improve understanding of rotor aerodynamics, acoustics, and dynamics, and lead to enhanced analytical methodology and design capabilities for the next generation of rotorcraft.

Yu, Yung H.↗
NASA NTRS1989

Airfoil stall penetration at constant pitch rate and high Reynolds number

The model wing consists of a set of fiberglass panels mounted on a steel spar that spans the 8 ft test section of the UTRC Large Subsonic Wind Tunnel. The first use of this system was to measure surface pressures and flow conditions for a series of constant pitch rate ramps and sinusoidal oscillations a Mach number range, a Reynolds number range, and a pitch angle range. It is concluded that an increased pitch rate causes stall events to be delayed, strengthening of the stall vortex, increase in vortex propagation, and increase in unsteady airloads. The Mach number range causes a supersonic zone near the leading edge, stall vortex to be weaker, and a reduction of unsteady airloads.

Lorber, Peter F.↗
NASA NTRS1988

An unsteady helicopter rotor: Fuselage interaction analysis

A computational method was developed to treat unsteady aerodynamic interactions between a helicopter rotor, wake, and fuselage and between the main and tail rotors. An existing lifting line prescribed wake rotor analysis and a source panel fuselage analysis were coupled and modified to predict unsteady fuselage surface pressures and airloads. A prescribed displacement technique is used to position the rotor wake about the fuselage. Either a rigid blade or an aeroelastic blade analysis may be used to establish rotor operating conditions. Sensitivity studies were performed to determine the influence of the wake fuselage geometry on the computation. Results are presented that describe the induced velocities, pressures, and airloads on the fuselage and on the rotor. The ability to treat arbitrary geometries is demonstrated using a simulated helicopter fuselage. The computational results are compared with fuselage surface pressure measurements at several locations. No experimental data was available to validate the primary product of the analysis: the vibratory airloads on the entire fuselage. A main rotor-tail rotor interaction analysis is also described, along with some hover and forward flight.

Lorber, Peter F.↗
NASA NTRS1987

An unsteady rotor/fuselage interaction method

An analytical method has been developed to treat unsteady helicopter rotor, wake, and fuselage interaction aerodynamics. An existing lifting line/prescribed wake rotor analysis and a source panel fuselage analysis were modified to predict vibratory fuselage airloads. The analyses were coupled through the induced flow velocities of the rotor and wake on the fuselage and the fuselage on the rotor. A prescribed displacement technique was used to distort the rotor wake about the fuselage. Sensitivity studies were performed to determine the influence of wake and body geometry on the computed airloads. Predicted and measured mean and unsteady pressures on a cylindrical body in the wake of a two-bladed rotor were compared. Initial results show good qualitative agreement.

Egolf, T. Alan↗