Search NASA⌕ Search

Engineering topics

Lore, J. D. (ORCID:000000029192465X)

Publications and source records attributed to Lore, J. D. (ORCID:000000029192465X).

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Multi-physics modeling of tungsten collector probe samples during the WEST C4 He campaign

Abstract We describe the results of a multi-scale, multi-physics modeling assessment of SOLPS-ITER, hPIC2, RustBCA and Xolotl, in which five single-crystal tungsten (W) samples were placed in a reciprocating collector probe and exposed to helium (He) plasma in the WEST fusion device. In our models, we considered a pure (100 %) He plasma, as well as one with oxygen (O) present (95% He 5% O) corresponding to the impurity concentration estimated during the C4 He campaign in WEST. Our SOLPS simulations approximately match experimental reciprocating Langmuir probe plasma measurements of plasma density and temperature. Using these plasma parameters as input, hPIC2 and RustBCA predict that the presence of oxygen impurities lead to a 15%–20% decrease in ion and heat fluxes to the surface, and an order of magnitude higher sputtering yields (compared with a pure He plasma). Xolotl predictions for the response of tungsten to plasma surface interactions (PSIs) agree with experimental LAMS analysis, and indicate large near-surface He concentrations, which quickly decay with depth. Our model also shows an increasing role of erosion—in removing the near-surface He—with time. Overall, slightly higher retention is predicted for tungsten exposed to a pure He plasma, with the largest differences in the near-surface gas content caused by the large oxygen-induced erosion. This highlights the important role that impurities play in PSI. Therefore, future work will focus on providing a fully self-consistent description of oxygen (and oxides, etc.) in our models, through multi-species implementation in GITR and inclusion of oxygen and tungsten oxide formation in Xolotl.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Time-dependent SOLPS-ITER simulations of the tokamak plasma boundary for model predictive control using SINDy *

Abstract Time-dependent SOLPS-ITER simulations have been used to identify reduced models with the sparse identification of nonlinear dynamics (SINDy) method and develop model-predictive control of the boundary plasma state using main ion gas puff actuation. A series of gas actuation sequences are input into SOLPS-ITER to produce a dynamic response in upstream and divertor plasma quantities. The SINDy method is applied to identify reduced linear and nonlinear models for the electron density at the outboard midplane n e , s e p O M P and the electron temperature at the outer divertor T e , s e p d i v . Note that T e , s e p d i v is not necessarily the peak value of T e along the divertor. The identified reduced models are interpretable by construction (i.e. not black box), and have the form of coupled ordinary differential equations. Despite significant noise in T e , s e p d i v , the reduced models can be used to predict the response over a range of actuation levels to a maximum deviation of 0.5% in n e , s e p O M P and 5%–10% in T e , s e p d i v for the cases considered. Model retraining using time history data triggered by a preset error threshold is also demonstrated. A model predictive control strategy for nonlinear models is developed and used to perform feedback control of a SOLPS-ITER simulation to produce a setpoint trajectory in n e , s e p O M P using the integrated plasma simulator framework. The developed techniques are general and can be applied to time-dependent data from other boundary simulations or experimental data. Ongoing work is extending the approach to model identification and control for divertor detachment, which will present transient nonlinear behavior from impurity seeding, including realistic latency and synthetic diagnostic signals derived from the full SOLPS-ITER output.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Novel SOLPS-ITER simulations of X-point target and snowflake divertors

Abstract The design and understanding of alternative divertor configurations may be crucial for achieving acceptable steady-state heat and particle material loads for magnetic confinement fusion reactors. Multiple X-point alternative divertor geometries such as snowflakes and X-point targets have great potential in reducing power loads, but have not yet been simulated widely in codes with kinetic neutrals. This paper discusses recent changes made to the SOLPS-ITER code to allow for the simulation of X-point target and low-field side snowflake divertor geometries. Snowflake simulations using this method are presented, in addition to the first SOLPS-ITER simulation of the X-point target. Analysis of these results show reasonable consistency with the simple modelling and theoretical predictions, supporting the validity of the methodology implemented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Investigation of core impurity transport in DIII-D diverted negative triangularity plasmas

Abstract Tokamak operation at negative triangularity has been shown to offer high energy confinement without the typical disadvantages of edge pedestals (Marinoni et al 2021 Nucl. Fusion 61 116010). In this paper, we examine impurity transport in DIII-D diverted negative triangularity experiments. Analysis of charge exchange recombination spectroscopy reveals flat or hollow carbon density profiles in the core, and impurity confinement times consistently shorter than energy confinement times. Bayesian inferences of impurity transport coefficients based on laser blow-off injections and forward modeling via the Aurora package (Sciortino et al 2021 Plasma Phys. Control. Fusion 63 112001) show core cross-field diffusion to be higher in L-mode than in H-mode. Impurity profile shapes remain flat or hollow in all cases. Inferred radial profiles of diffusion and convection are compared to neoclassical, quasilinear gyrofluid, and nonlinear gyrokinetic simulations. Heat transport is observed to be better captured by reduced turbulence models with respect to particle transport. State-of-the-art gyrokinetic modeling compares favorably with measurements across multiple transport channels. Overall, these results suggest that diverted negative triangularity discharges may offer a path to a highly-radiative L-mode scenario with high core performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

High gas throughput SOLPS-ITER simulations extending the ITER database to strong detachment

Abstract SOLPS-ITER simulations performed for Q DT = 10, P SOL = 100 MW burning plasmas on ITER extend the existing database to high values of separatrix averaged neon impurity concentration (⟨ c Ne ⟩ ≈ 6%) and divertor neutral pressure (⟨ p div ⟩ > 25 Pa) in order to determine the heat flux mitigation capability of these scenarios and whether strongly detached states are accessible. In the existing database of ITER simulations, the level of detachment was limited to cases where the integral ion flux to the outer target was greater than 80% of the value at rollover, with the impurity radiation localized near the target. With the possibility of narrow heat flux channels and increased deposited power due to tile shaping, it is important to explore operation at a higher degree of detachment. Two series of simulations were explored to extend the database of SOLPS simulations. By increasing the deuterium and neon puff rates proportionally, the peak divertor energy flux ( q ⊥,max ) is decreased from 5 to 3 MW m −2 while ⟨ p div ⟩ increased from 11 to 27 Pa. By increasing only the neon puff, q ⊥, max can be reduced to <1MW m −2 while ⟨ p div ⟩ is maintained at ∼ 11 Pa. As the neon puff level is increased, the position of the impurity radiation peak is shifted towards the X-point. At the highest neon puff levels with steady-state solutions, the electron temperature is reduced below 1 eV across 50 cm of each divertor target. The new cases extend previously observed tight relationships in power and momentum loss factors to low electron temperature improving their utility for highly detached regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Ponderomotive force driven density modifications parallel to B on the LAPD

The ponderomotive force has previously been identified as a possible driver of observed density modifications close to radio frequency actuators during operation. This nonlinear force redistributes density in regions of gradients in the magnitude of an oscillating electric field and describes the influence of the fast time scale RF wave dynamics on slow time scale plasma transport. Depletion of the saturation current (a proxy for the density) measured at the Large Plasma Device (LAPD) was 30–35% during ion cyclotron range of frequencies operation. A coupled 1D plasma transport and cold plasma frequency domain wave solver was developed to self-consistently describe ponderomotive effects and was used to compare with results obtained from the LAPD experiment. The scaled current density driver for the wave model yielded an RF B field in close agreement with two components of the experimental data. However, the 1D parallel model did not accurately reproduce the amplitude or spatial distribution observed in experimental measurements of By. Within the limitations of the 1D model, initial simulation results showed that the ponderomotive force depleted up to 8% for high power (1 MW) and around 1% for the experimental power of 120 kW. This could suggest that the ponderomotive force is not the main driver of density modification for the LAPD experiments presented in this paper. Higher fidelity tools of at least 2D will be required to give a more realistic description of the RF E fields and the effect of the ponderomotive force on the LAPD.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗