Experimental Determination of Chapman-Jouguet Pressure Using Disc Acceleration eXperiment (DAX) Data
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Lorenz, K T.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Abstract not provided
Abstract not provided
Abstract not provided
Abstract not provided
Experimental results showing significant reductions from classical in the Rayleigh-Taylor (RT) instability growth rate due to high pressure effective lattice viscosity in metal foils are presented. Stabilization of RT instability (RTI) by ablation and density gradients has been studied for decades. The regime of stabilized RTI due to material strength at high pressure is new. On the Omega Laser in the Laboratory for Laser Energetics, University of Rochester, target samples of polycrystalline vanadium are compressed and accelerated quasi-isentropically at approx1 Mbar pressures, while maintaining the samples in the solid-state. Provided strong shocks are avoided, the higher the applied peak pressure, the higher the predicted foil strength, and hence, the higher the degree of strength stabilization of RTI. Several experiments were conducted where the amount of RT growth is measured by face-on radiography. The vanadium samples are probed by a laser driven He-alpha x-ray backlighter which produced 5.2 keV radiation. Comparison of the results with constitutive models for solid state strength under these conditions show that the measured RT growth is substantially lower than predictions using existing models that work well at low pressures and long time scales. High pressure, high strain rate data can be explained by the enhanced strength due to a phonon drag mechanism, creating a high effective lattice viscosity.
Abstract not provided
The pressure dependent deflagration rates of LLM-105, DAAF and TATB based formulations were measured in the LLNL high pressure strand burner. The role of binder amount, explosive type, and thermal damage and their effects on the deflagration rate will be discussed. One DAAF formulation, two different formulations of LLM-105, and four formulations of TATB were studied; results indicate that binder amount and type play a minor role in the deflagration behavior. This is in sharp contrast to the HMX based formulations which strongly depend on binder amount and type. The effect of preheating these samples was considerably more dramatic. In the case of LLM-105, preheating the sample appears to have little effect on the deflagration rate. In contrast, preheating DAAF and TATB formulations causes the deflagration rate to accelerate. The thermal and mechanical properties of these formulations will be discussed in the context of their pressure and temperature dependent deflagration rates.
Experimental results showing significant reductions from classical in the Rayleigh-Taylor (RT) instability growth rate due to high pressure material strength or effective lattice viscosity in metal foils are presented. On the Omega Laser in the Laboratory for Laser Energetics, University of Rochester, target samples of polycrystalline vanadium are compressed and accelerated quasi-isentropically at {approx}1 Mbar pressures, while maintaining the samples in the solid-state. Comparison of the results with constitutive models for solid state strength under these conditions show that the measured RT growth is substantially lower than predictions using existing models that work well at low pressures and long time scales. High pressure, high strain rate data can be explained by the enhanced strength due to a phonon drag mechanism, creating a high effective lattice viscosity.
This paper outlines the characterization of voids and Microstructure in TATB-based Explosives over several orders of magnitude, from sizes on the order of 10 nm to about 1 cm. This is accomplished using ultra small angle x-ray scattering to investigate voids from a few nm to a few microns, ultra small angle neutron scattering for voids from 100 nm to 10 microns, and x-ray computed microtomography to investigate microstructure from a few microns to a few centimeters. The void distributions of LX-17 are outlined, and the microstructure of LX-17 is presented. Temperature cycling and compressive creep cause drastically different damage to the microstructure. Temperature cycling leads to a volume expansion (ratchet growth) in TATB-based explosives, and x-ray scattering techniques that are sensitive to sizes up to a few microns indicated changes to the void volume distribution that had previously accounted for most, but not all of the change in density. This paper presents the microstructural damage larger than a few microns caused by ratchet growth. Temperature cycling leads to void creation in the binder poor regions associated with the interior portion of formulated prills. Conversely, compressive creep causes characteristically different changes to microstructure; fissures form at binder-rich prill boundaries prior to mechanical failure.
Experimental results showing significant reductions from classical in the Rayleigh-Taylor (RT) instability growth rate due to high pressure effective lattice viscosity are presented. Using a laser created ramped drive, vanadium samples are compressed and accelerated quasi-isentropically at {approx}1 Mbar pressures, while maintaining the sample in the solid-state. Comparisons with simulations and theory indicate that the high pressure, high strain rate conditions trigger a phonon drag mechanism, resulting in the observed high effective lattice viscosity and strong stabilization of the RT instability.
The pressure dependent deflagration rates of LLM-105 and TATB based formulations were measured in the LLNL high pressure strand burner. The role of binder amount, explosive type, and thermal damage and their effects on the deflagration rate will be discussed. Two different formulations of LLM-105 and three formulations of TATB were studied and results indicate that binder amount and type play a minor role in the deflagration behavior. This is in sharp contrast to the HMX based formulations which strongly depend on binder amount and type. The effect of preheating these samples was considerably more dramatic. In the case of LLM-105, preheating the sample appears to have little effect on the deflagration rate. In contrast, preheating TATB formulations causes the deflagration rate to accelerate and become erratic. The thermal and mechanical properties of these formulations will be discussed in the context of their pressure and temperature dependent deflagration rates.
A new recovery based method for investigating material response to non-Hugoniot loading paths is described. The work makes use of a laser generated plasma piston that produces ramped loading at high strain rates (> {approx} 10{sup 7}/s). Large sample sizes are utilized to prevent reflected wave interactions. The overall deformation path is characterized by two transients: one at very high strain rate on the 5-10 nanosecond time scale and one at a lower strain rate occurring over a 1-2 microsecond timescale. It was found that a sufficiently large region of material experiences shockless loading conditions such that recovery based characterization is feasible. The presence of two strain transients makes the method more applicable to comparative assessments between shockless and shock loading conditions.
We present experiments on the Rayleigh-Taylor (RT) instability in the plastic flow regime of solid-state vanadium (V) foils at {approx}1 Mbar pressures and strain rates of 10{sup 6}-10{sup 8} s{sup -1}, using a laser based, ramped-pressure acceleration technique. High pressure material strength causes strong stabilization of the RT instability at short wavelengths. Comparisons with 2D simulations utilizing models of high pressure strength show that the V strength increases by a factor of 3.5 at peak pressure, compared to its ambient strength. An effective lattice viscosity of {approx}400 poise would have a similar effect.