Engineering topics

Loving, Donald L.

Publications and source records attributed to Loving, Donald L..

5 records

NASA NTRS1961

A Transonic Investigation of Changing Indentation Design Mach Number on the Aeodynamic Characteristics of a 45 deg Sweptback-Wing-Body Combination Designed for High Performance

The effects of changing indentation design Mach number on the aerodynamic characteristics of a 45 deg. sweptback-wing-body combination designed for high performance have been investigated at Mach numbers from 0.80 to 1.13 in the Langley 8-foot transonic tunnel and at a Mach number of 1.43 in the Langley 8-foot transonic pressure tunnel. The Reynolds number of the investigation covered the range from approximately 2.5 x 10 (exp 6) to approximately 3.0 x 10(exp 6) based on the mean aerodynamic chord of the wing. The 45 deg. sweptback wing with camber and a thickened root was tested at 0 deg. angle of incidence on an unindented body and on bodies indented for Mach numbers M of 1.0, 1.2, and 1.4. Transonic and supersonic area rules were used in the design of the indented bodies. Theoretical zero-lift wave drag was calculated for these wing-body combinations. A -2 deg. angle of incidence of the wing, and M = 1.4 revised body indentation, and fixed transition also were investigated. Experimental values of zero-lift wave drag for the indented-body combinations followed closely the area-rule concept in that the lowest zero-lift wave-drag coefficient was obtained at or near the Mach number for which the body of the combination was designed. Theoretical values of zero-lift wave drag were considered to be in good agreement with the experimental results. At a given supersonic Mach number the highest values of maximum lift-drag ratio for the various combinations also were obtained at or near the Mach number for which the body of the combination was designed. At Mach numbers of 1.0, 1.2, and 1.43, the maximum lift-drag ratios were 15.3, 13.0, and 9.2, respectively. The use of an angle of incidence of -2 deg. for the wing in combination with the M = 1.2 body increased the zero-lift wave drag and decreased the maximum lift-drag ratio. All configurations maintained stable characteristics up to the highest lift coefficient of the investigation (C(L) approx. equal to 0.5).

Loving, Donald L.↗

NASA NTRS1961

A Wind-Tunnel Investigation of a Transonic-Transport Configuration Utilizing Drag-Reducing Devices at Mach Numbers from 0.20 to 1.03

The static longitudinal stability and control and lateral characteristics of a transonic-transport model, incorporating recent drag-reducing devices, has been investigated in the Langley 8-foot transonic pressure tunnel. The wing was cambered, had a thickened root and a taper ratio of 0.3. Wing sweepback angles of 45 degrees and 40 degrees were investigated with corresponding aspect ratios of 7 and 8, respectively. Modifications to the model for reducing the drag were: a forward fuselage addition and special bodies (four big enough to house jet engines) added to the upper surface of the wing. Other components and changes investigated included an empennage, a wing-tip body, wing fences, wing trailing-edge flaps, horizontal-tail settings, and wing dihedral angle. The investigation covered the Mach number range from 0.20 to 1.03 for the angle-of-attack range from -5 degrees to 15.4 degrees, and a sideslip angle of -5 degrees, in the Reynolds number range from 0.52 times 10(exp 6) to 1.94 times 10(exp 6) based on the wing mean aerodynamic chord. The various fuselage and wing additions delayed the drag-rise Mach number and greatly reduced the drag beyond the drag rise. The wing bodies markedly alleviated unstable pitch tendencies throughout the test Mach number range. At low landing speeds, the wing bodies exhibited little interference with the ability of trailing-edge flaps to increase the lift near maximum lift coefficient; and the use of fences greatly reduced the severe longitudinal instability trend at landing attitudes. The model with a 6 degree dihedral angle exhibited positive lateral and directional stability characteristics in the presence of the fuselage and wing additions. An increase in drag-rise Mach number associated with the fuselage and wing additions on the 40 degree sweptback wing combination was similar to that for the comparable 45 degree combination. These additions did, however, reduce the drag of the 40 degree sweptback configurations more than the 45 degree configurations in the transonic speed range.

Loving, Donald L.↗

NASA NTRS1961

An Investigation of the Influence of Body Size and Indentation Asymmetry of the Effectiveness of Body Indentation in Combination with a Cambered Wing

An investigation has been made of a 450 sweptback cambered wing in combination with an unindented body and a body symmetrically indented with respect to its axes designed for a Mach number of 1.2. The ratio of body frontal area to wing planform area was 0.08 for these wing-body combinations. In order to determine the influence of body size on the effectiveness of indentation, the test data have been compared with previously obtained data for similar configurations having a ratio of body frontal area to wing planform area of 0.04. Also, in order to investigate the relative effectiveness of indentation asymmetry, a specially indented body designed to account for the wing camber and also designed for a Mach number of 1.2 has been included in these tests. The investigation was conducted in the Langley 8-Foot Tunnels Branch at Mach numbers from 0.80 to 1.43 and a Reynolds number of approximately 1.85 x 10(exp 6), based on a mean aerodynamic chord length of 5.955 inches. The data indicate that the configurations with larger ratio of body frontal area to wing planform area had smaller reductions in zero-lift wave drag associated with body indentation than the configurations with smaller ratio of body frontal area to wing planform area. The 0.08-area-ratio configurations also had correspondingly smaller increases in the values of maximum lift-drag ratio than the 0.04-area-ratio configurations. The consideration of wing camber in the body indentation design resulted in a 35.5-percent reduction in zero-lift wave drag, compared with a 21.5-percent reduction associated with the symmetrical indentation, but had a negligible effect on the values of maximum lift-drag ratio.

Patterson, James C., Jr.↗

NASA NTRS1959

The Fluorescent-Oil Film Method and Other Techniques for Boundary-Layer Flow Visualization

A flow-visualization technique, known as the fluorescent-oil film method, has been developed which appears to be generally simpler and to require less experience and development of technique than previously published methods. The method is especially adapted to use in the large high-powered wind tunnels which require considerable time to reach the desired test conditions. The method consists of smearing a film of fluorescent oil over a surface and observing where the thickness is affected by the shearing action of the boundary layer. These films are detected and identified, and their relative thicknesses are determined by use of ultraviolet light. Examples are given of the use of this technique. Other methods that show promise in the study of boundary-layer conditions are described. These methods include the use of a temperature-sensitive fluorescent paint and the use of a radiometer that is sensitive to the heat radiation from a surface. Some attention is also given to methods that can be used with a spray apparatus in front of the test model.

Loving, Donald L.↗

NASA NTRS1953

High-Speed Wind-Tunnel Tests of a 1/16-Scale Model of the D-558 Research Airplane Lift and Drag Characteristics of the D-558-1 and Various Wing and Tail Configurations

Tests were made in the Langley 8-foot high-speed tunnel to investigate the aerodynamic characteristics of the D-558-1 airplane and various wing and tail configurations on the D-558-1 fuselage. The various wing and tail configurations were tested to determine the aerodynamic effects of aspect ratio and sweep for suitable use on the second phase of the D-558 project (D-558-2). The tests were conducted through a speed range from a Mach number of 0.40 to approximately 0.94.This part of the investigation includes the lift and drag results available for the configurations tested at this rate. The D-558-1 results indicated that the lift force break would occur at a Mach number of 0.85 with some reduction in lift at speeds above this Mach number. Tests indicated that the airplane will have satisfactory lift and drag characteristics up to and including its design Mach number of 0.85. The 35deg sweptback, 35deg swept-forward, and low-aspect-ratio (2.0) wing configurations all showed pronounced improvements in maintaining lift throughout the Mach number range tested and in increasing the critical speeds above the D-558-1 value &itical to critical Mach numbers on the order of 0.9. Insofar as lift and drag characteristics are concerned level flight at speeds approaching the velocity of sound appears practical if swept or low-aspect-ratio configurations similar to those tested are used.

Wright, John D.↗