Search NASA⌕ Search

Engineering topics

Lu, Kathy

Publications and source records attributed to Lu, Kathy.

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

In-situ TEM study of Kr ion irradiation tolerance of SiFeOC nanocomposite

Here, in this work, ion irradiation of polymer derived SiFeOC nanocomposite was carried out using 1.2 MeV Kr ions at room temperature and 600°C. The starting composite was composed of Fe 3 Si, SiC, SiOC, SiO 2 , and graphitic C. In-situ TEM investigations show uniform distribution of nano-crystalline Fe 3 Si and SiC phases in the amorphous SiOC matrix. During ion irradiation, the SiOC bulk microstructure and interfaces between Fe 3 Si or SiC crystallites and the SiOC matrix remain defect-free and demonstrate outstanding ion irradiation resistance. At room temperature, the crystalline domains are stable up to 2 dpa. At 600°C, Fe 3 Si crystallites are more stable than SiC; SiC crystallites are stable up to 4 dpa while the Fe 3 Si crystallites are stable up to 10 dpa. These crystallites also coalescence and amorphize simultaneously during ion irradiation. The exceptional tolerance to defect formation and irradiation of the SiFeOC nanocomposite provides important guidance to developing irradiation resistant fuels for advanced gas cooled reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In-situ microstructure observation of oxidized SiC layer in surrogate TRISO fuel particles under krypton ion irradiation

In accidental scenarios of high temperature gas-cooled reactors, both oxidation of and irradiation to the SiC layer in tri-structural-isotropic (TRISO) fuel particles can change the microstructure and integrity of the fuel elements. Here, in the present study, microstructure and defect evolution in the oxidized SiC layer of surrogate TRISO fuel particles under 1.2 MeV krypton ion irradiation was observed by in-situ transmission electron microscopy. The SiC layers oxidized in water vapor at 1200 °C were irradiated azt room temperature and 800 °C and at damage levels of 0.28–11.2 dpa, respectively. SiC and SiO 2 were found to still be in their crystal structures at the damage level of 11.2 dpa at 800 °C, while SiC was observed to have been amorphized at only 0.56 dpa irradiation at room temperature. The defect number density at 800 °C was an order of magnitude lower than that in the sample irradiated at room temperature. Also, crystalline SiO 2 had higher radiation resistance compared to SiC. A defect reaction rate theory was utilized to understand the fundamental defect evolution process and irradiation resistance difference.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Effects of processing temperature on the corrosion and tribocorrosion resistance of perhydropolysilazane-derived coatings on AISI 304 steel

Ensuring a highly corrosion and erosion resistant surface is critical to the reliability and structural integrity of steel canisters for long-term nuclear waste storage in corrosive environments. In this work, perhydropolysilazane (PHPS)-derived coating has been successfully applied to enhance the pitting and tribocorrosion resistance of 304 stainless steels in 0.6 M NaCl solution. Two types of coatings were synthesized on the stainless steel substrate by crosslinking PHPS at room temperature or 600 °C, resulting in different mechanical and corrosion performance. Further, Raman spectra revealed that Si-O bonds were generated in the coating crosslinked at room temperature after corrosion, while absent in that pyrolyzed at 600 °C. In tribocorrosion tests, both coatings were protective to the steel substrate, with the protective effect being more pronounced in the 600 °C pyrolyzed coating. Overall, the PHPS-derived coating synthesized at 600 °C exhibited better protection for steel in wear and corrosion coexisting environments than those synthesized at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Polysiloxane coatings on microspheres based on Multiphase Flow with Interface Exchange-Discrete Element Modelling

Polysiloxane coatings on yttria stabilized zirconia (YSZ) microspheres of 500 μm were simulated in a spout fluidized bed coater using Multiphase Flow with Interface Exchange-Discrete Element Modelling (MFiX-DEM). In this work, two different coater configurations were developed to study the influence of gas velocity and its distribution on particle dynamics. The presence of the Wurster tube not only enhances the distribution but also increases the overall residence time of the particles. Investigations were also carried out with different Wurster tube positions (normal, 10% and 20% lowered from its initial position). Among these, 20% lowered Wurster tube position demonstrated the most effective coating process. The effects of gas inlet pressure on the average gas velocity and the distribution of particles were analyzed. More than 97% of the particles can be retained. The derived results, including average gas velocity, particle retention percentage, and distribution of particles with gas velocity, are being used to guide the experimental work in obtaining defect-free coatings for YSZ microspheres.

36 MATERIALS SCIENCE↗
DOE OSTI2021

SiOC coatings on yttria stabilized zirconia microspheres using a fluidized bed coating process

In this study, defect-free SiOC coatings were prepared on yttria stabilized zirconia (YSZ) microspheres by a fluidized bed coating process. Effects of the rheological properties of the coating solution on the coating process were elucidated. An impact regime diagram was constructed, which demonstrated that the coating mechanisms were collision/impact. During the fluidized bed coating, longer spouted time resulted in wider dispersion, longer residence time, and more circulatory motion of particles; the fluid distributed more uniformly throughout the column, as demonstrated in our Multiphase Flow with Interface eXchange (MFiX) simulations. Two-step pyrolysis in Ar achieved complete coating layers, which were comprised of SiOC, SiO 2 , SiC, and graphite. The two stage mass loss during the pyrolysis corresponded to simultaneous reactions due to depolymerization and hydrocarbon loss from 400 to 600°C. Carbon cluster size in the pyrolyzed samples was calculated to be 25 ± 2 Å. In conclusion, this work provides a new method for producing SiOC coatings on micron spheres, with nuclear TRISO fuel particles as the application.

42 ENGINEERING↗
DOE OSTI2021

Oxidation behaviors of matrix-grade graphite during water vapor ingress accidents for high temperature gas-cooled reactors

Water ingress into cores of high temperature gas-cooled reactors (HTGRs) can cause serious safety problems in graphitic components, especially for matrix graphite, which is more vulnerable than nuclear graphite. Here in this study, oxidation behaviors of a matrix-grade graphite, ARB-B1, were investigated under simulated water ingress accidental conditions. The oxidation tests were conducted in water vapor/helium mixed atmospheres at elevated temperatures up to 1200 °C. Oxidation rates and activation energy were evaluated by mass loss measurements. The activation energy was 121.5 kJ/mol in the considered temperature range, indicating only one oxidation regime-in-pore diffusion assisted by cracks. The cracks originated from the fabrication process, acting as penetration paths for the oxidant, played an important role in the oxidation behaviors. Ungraphitized binder oxidation occurred at all temperatures, while apparent oxidation of filler particles started from 1100 °C. Moreover, oxidation effects on compressive properties and hardness of the matrix graphite were discussed in terms of oxidized microstructures. This first detailed study on matrix graphite oxidation in water vapor provides important kinetics knowledge and microstructural and mechanical data for accidental scenarios of HTGRs as well as for development of new matrix graphite materials.

36 MATERIALS SCIENCE↗