Search NASA⌕ Search

Engineering topics

Lu, Tianfeng

Publications and source records attributed to Lu, Tianfeng.

15 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

An iterative dynamic chemical stiffness removal method for reacting flow simulations

Abstract An iterative dynamic chemical stiffness removal method (IDCSR) based on quasi-steady-state approximation (QSSA) is proposed. The IDCSR method is built on a previously developed non-iterative method which has proved to work well for small timestep sizes. A novel iterative procedure is designed in IDCSR to enable explicit time integration of stiff chemistry at relatively large timestep sizes relevant to practical reacting flow simulations. The effectiveness of the iterative procedure is first demonstrated with a toy problem and homogeneous auto-ignition with fixed integration step sizes, showing that larger timestep sizes can be allowed for explicit time integration using IDCSR compared with the previous non-iterative method. IDCSR is then compared with existing explicit chemistry solvers for simulations of homogeneous auto-ignition and shows similar or lower computational cost but significantly higher accuracy across a wide range of timestep sizes. IDCSR is further combined with an automatic adaptive time-stepping scheme for simulations of 0-D homogeneous auto-ignition and a 2-D laminar lifted n -dodecane jet flame. For the 0-D auto-ignition simulations, IDCSR is shown to reduce both the error (by 43%–90%) and computational cost (by 6–15 times) compared with existing explicit solvers, while achieving speed-up factors of up to 400 compared with VODE for a wide range of timestep sizes and reaction mechanisms. For the 2-D jet flame simulations, speed-up factors of 15 and 31 for chemistry integration, and 5 and 9 for overall simulation, are achieved by IDCSR compared with CVODE with and without analytic Jacobian, respectively.

Xu, Chao (ORCID:0000000153074159)↗
DOE OSTI2023

PELE - Transforming Combustion Science and Technology with Exascale Simulations

This poster presents the status of the Pele Combustion project, an applications project in the Exascale Computing Project. It summarizes the goal of the projects, developments added to the Pele simulation capabilities over the last year, some example performance figures that target ultimate application on the Frontier supercomputer, and show a number of published and in-progress simulation results, by us and our collaborators.

combustion↗
DOE OSTI2022

A direct numerical simulation study of the dilution tolerance of propane combustion under spark-ignition engine conditions

Modern spark ignition internal combustion (IC) engines rely on highly diluted fuel-air mixtures to achieve high brake thermal efficiencies. To support this, new engine designs have introduced high stroke-to-bore ratios and cylinder head designs that promote high tumble flow and turbulence intensities. However, mixture dilution through exhaust gas recirculation (EGR) is limited by combustion instabilities manifested in the form of cycle-to-cycle variability. Propane has been observed to have superior EGR dilution tolerance than gasoline, which makes it a very competitive low-carbon fuel for the new IC engines without sacrificing efficiency. Two-dimensional direct numerical simulations (DNS) are performed with detailed chemistry to study and contrast the effect of turbulence intensity and dilution on propane and iso-octane premixed flames at high pressure conditions similar to those in-cylinder. A new reduced mechanism for propane consisting of 53 transported species and 17 quasi-steady state species is developed based on a previously published mechanism and used in these simulations. Three levels of turbulence intensity and two levels of exhaust gas dilution are chosen based on conditions relevant to IC engine operation. The DNS results are analyzed based on the evolution of the flame surface area and the statistics of its driving terms, which are found to be similar for both fuels when there is no dilution but considerably different under high dilution. The analysis of the DNS data provides fundamental insights into the underlying mechanisms for improved stability under dilution.

42 ENGINEERING↗
DOE OSTI2022

Effects of non-thermal termolecular reactions on detonation development in hydrogen (H 2 )/methane (CH 4 ) - air mixtures

The binary fuel blend of H 2 /CH 4 is one of the most promising hydrogen-enriched hydrocarbon fuels in spark-ignition (SI) engines. Yet, the undesirable phenomenon of super-knock, which can severely and in-stantaneously damage an SI engine, limits its widespread adoption. Moreover, there is still a lack of con-sensus on the precise mechanism by which this phenomenon occurs i.e. via flame acceleration or spon-taneous ignition, despite numerous previous investigations. At the same time, recent studies [M. P. Burke, S. J. Klippenstein, Nat. Chem. 9 (2017) 1078 -1082, Y. Tao, A. W. Jasper, Y. Georgievskii, S. J. Klippenstein, R. Sivaramakrishnan, Proc. Combust. Inst. 38 (2021) 515-522] have demonstrated a high probability of occurrence of non-thermal reactions in premixed flames of such H 2 /CH 4 fuel blends with air due to the presence of non-trivial amounts of highly reactive radicals including H, O and OH apart from O 2 . The present study focuses on the evolution of an initial deflagration front to a detonation wave in H 2 /CH 4 - air mixtures under SI engine relevant conditions through fully resolved, constant volume 1D simulations with and without non-thermal reactivity. Non-thermal reactions were included in the macroscopic kinetics model as chemically termolecular reactions facilitated by the H + CH 3 and H + OH radical-radical recombination and the H + O 2 radical-molecule association reactions. Further, the nonthermal reactions result in a corresponding decrease in the reaction fluxes of the incipient recombination/association reactions. Therefore, an additional set of simulations were performed by applying corrections to the respective incipient recombination/association rate constants using the methodology demonstrated by Tao et al. [Y. Tao, A. W. Jasper, Y. Georgievskii, S. J. Klippenstein, R. Sivaramakrishnan, Proc. Combust. Inst. 38 (2021) 515-522]. Compared to the baseline case, the onset of spontaneous ignition in the end-gas region was observed to be delayed in the presence of non-thermal termolecular reactions. Concurrently, the developing detonation was observed to be significantly stronger. In contrast, applying corrections to the recombi-nation/association rate constants resulted in a completely different behavior. Specifically, detonation was observed to occur due to self acceleration of the primary flame in the absence of spontaneous ignition in the end-gas region. Sensitivity analysis was performed to quantify the effects of non-thermal reactions on the duration of heat release rate and thereby the mechanism of detonation formation. In addition, chemical explosive mode analysis (CEMA) was performed to identify the dominant species/reactions re-sponsible for the observed results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Simulations of Multi-Mode Combustion Regimes Realizable In a Gasoline Direct Injection Engine

Lean and dilute gasoline compression ignition (GCI) operation in spark ignition (SI) engines are an attractive strategy to attain high fuel efficiency and low NOx levels. However, this combustion mode is often limited to low-load engine conditions due to the challenges associated with autoignition controllability. In order to overcome this constrain, multi-mode (MM) operating strategies, consisting of advanced compression ignition (ACI) at low load and conventional SI at high load, have been proposed. In this three-dimensional computational fluid dynamics study, the concept of multi-mode combustion using two RON98 gasoline fuel blends (Co-Optima Alkylate and E30) in a gasoline direct injection (GDI) engine were explored. To this end, a new reduced mechanism for simulating the kinetics of E30 fuel blend is introduced in this study. To cover the varying engine load demands for multi-mode engines, primary combustion dynamics observed in ACI and SI combustion modes was characterized and validated against experimental measurements. In order to implement part-load conditions, a strategy of mode transition between SI and ACI combustion (i.e., mixed-mode combustion) was then explored numerically by creating a virtual test condition. The results obtained from the mixed-mode simulations highlight an important feature that deflagrative flame propagation regime coexists with ignition-assisted end-gas autoignition. This study also identifies a role of turbulent flow property adjacent to premixed flame front in characterizing the mixed-mode combustion. The employed hybrid combustion model was verified to perform simulations aiming at suitable range of multi-mode engine operations.

Kim, Sayop↗
DOE OSTI2021

Effects of non-thermal termolecular chemistry on detonation development in hydrogen (H2) / methane (CH4) - air mixtures

In combustion simulations, it is usually assumed that highly-energized collision complexes (either radical or stable species) formed in exothermic reactions are always under thermal equilibrium as they evolve through competing networks of reactions. However, in practical flames, non-trivial amounts of reactive radicals such as H, O and OH are present apart from O2. As a result, collisions of these reactive species with the energized collision complexes have been shown in recent studies to induce non-thermal reactivity. These studies have also demonstrated that such non-thermal reactions can be suitably represented in macroscopic kinetics models as chemically termolecular reactions. The present work was focused on identifying and quantifying the effects of including such reactions on the evolution of an initial deflagration front to a developing detonation in H2/CH4-air mixtures under boosted internal combustion (IC) engine conditions. Specifically, fully resolved simulations, with and without non-thermal reactivity, were performed for a constant volume reactor containing stoichiometric H2/CH4-air mixture. It was found that inclusion of termolecular chemistry resulted in a delayed onset of end-gas auto-ignition. Concurrently, the developing detonation intensity was observed to be significantly higher. Chemical explosive mode analysis (CEMA) was performed to identify the dominant species/reactions responsible for the observed variation in the results.

Detonation↗
DOE OSTI2021

Numerical Analysis of Fuel Effects on Advanced Compression Ignition Using a Cooperative Fuel Research Engine Computational Fluid Dynamics Model

Growing environmental concerns and demand for a better fuel economy are driving forces that motivate the research for more advanced engines. Multi-mode combustion strategies have gained attention for their potential to provide high thermal efficiency and low emissions for light-duty applications. These strategies target optimizing the engine performance by correlating different combustion modes to load operating conditions. The extension from boosted spark ignition (SI) mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing the compression ratio and utilizing intake air heating. Further, in order to enable an accurate control of intake charge condition for ACI mode and rapid mode-switches, it is essential to gain fundamental insights into the autoignition process. Within the scope of ACI, homogeneous charge compression ignition (HCCI) mode is of significant interest. It is known for its potential benefits, operation at low fuel consumption, low NOx, and particulate matter (PM) emissions. In the present work, a virtual Cooperative Fuel Research (CFR) engine model is used to analyze fuel effects on ACI combustion. In particular, the effect of fuel octane sensitivity (S) (at constant Research Octane Number (RON)) on autoignition propensity is assessed under beyond-RON (BRON) and beyond-MON (BMON) ACI conditions. The three-dimensional CFR engine computational fluid dynamics (CFD) model employs a finite-rate chemistry approach with a multi-zone binning strategy to capture autoignition. Two binary blends with Research Octane Number (RON) of 90 are chosen for this study: primary reference fuel (PRF) with S = 0 and toluene–heptane (TH) blend with S = 10.8, representing paraffinic and aromatic gasoline surrogates. Reduced mechanisms for these blends are generated from a detailed gasoline surrogate kinetic mechanism. Simulation results with the reduced mechanisms are validated against experimental data from an in-house CFR engine, with respect to in-cylinder pressure, heat release rate, and combustion phasing. Thereafter, the sensitivity of combustion behavior to ACI operating condition (BRON versus BMON), air-fuel ratio (λ = 2 and 3), and engine speed (600 and 900 rpm) is analyzed for both fuels. It is shown that the sensitivity of a fuel’s autoignition characteristics to λ and engine speed significantly differs at BRON and BMON conditions. Moreover, this sensitivity is found to vary among fuels, despite the same RON. It is also observed that the presence of low-temperature heat release (LTHR) under BRON condition leads to more sequential autoignition and longer combustion duration than BMON condition. Finally, the study indicates that the octane index (OI) fails to capture the trend in the variation of autoignition propensity with S under the BMON condition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Numerical Investigation of a Central Fuel Property Hypothesis Under Boosted Spark-Ignition Conditions

In the present work, a central fuel property hypothesis (CFPH), which states that fuel properties are sufficient to provide an indication of a fuel’s performance irrespective of its chemical composition, was numerically investigated. In particular, the objective of the study was to determine whether Research Octane Number (RON) and Motor Octane Number (MON), as fuel properties, are sufficient to describe a fuel’s knock-limited performance under boosted spark-ignition (SI) conditions within the framework of CFPH. To this end, four TPRF-bioblendstock surrogates having different compositions but matched RON (=98) and MON (=90), were first generated using a non-linear regression model based on artificial neural network (ANN). Additionally, three unconventional bioblendstocks were included in the analysis: di-isobutylene (DIB), isobutanol, and Anisole. Skeletal reaction mechanisms were generated for the TPRF-DIB, TPRF-isobutanol, and TPRF-anisole blends from a detailed kinetic mechanism. Thereafter, numerical simulations were performed for the fuel surrogates using the skeletal mechanisms and a virtual cooperative fuel research (CFR) engine model, under a representative boosted operating condition. In the computational fluid dynamics (CFD) model, the G-equation approach was employed to track the turbulent flame front and the well-stirred reactor model combined with the multi-zone binning strategy was used to capture auto-ignition in the end-gas. In addition, laminar flame speed (LFS) was tabulated for each blend as a function of pressure, temperature, and equivalence ratio a priori, and the lookup tables were used to prescribe laminar flame speed as an input to the G-equation model. Parametric spark timing sweeps were performed for each fuel blend to determine the corresponding knock-limited spark advance (KLSA) and 50% burn point (CA50) at the respective KLSA timing. It was observed that despite same RON, MON, and engine operating conditions, the TPRF-anisole blend exhibited markedly different knock-limited performance from the other three blends. This deviation from the octane index (OI) expectation was shown to be caused by differences in laminar flame speed. However, it was found that relatively large fuel-specific differences in LFS (>20%) would have to be present to cause any appreciable deviation from the OI framework. Otherwise, RON and MON would still be robust enough to predict a fuel’s knock-limited performance.

42 ENGINEERING↗
DOE OSTI2020

A direct numerical simulation of Jet A flame kernel quenching

The safe operation of aeronautical engines requires an understanding of flame ignition, propagation and extinction. In this study, direct numerical simulations are performed using a 29 species reduced chemical mechanism for jet fuel surrogate Jet A to understand the flame quenching process. Here, initially laminar spherical flames of varying sizes and equivalence ratios are subject to an identical periodic domain of decaying and isotropic high intensity turbulence with a turbulent Reynolds number of 2400. All cases become quenched, except for the larger kernel with lower Karlovitz number. An analysis of the flame structure shows broadened preheat zone, flame shortening on the product side, differential species diffusion and partial fuel pyrolysis in the fresh mixture. Two extinction mechanisms are identified arising from flame shortening and high flame stretch. Flame shortening occurs due to turbulence-chemistry interactions that resemble the flame–flame interaction in a laminar counterflow reactant-to-reactant configuration, which contorts and breaks up the ignition kernel. Flame stretch is a local effect that attenuates the heat release rate and causes the flame to retreat towards the product mixtures, similar to what has been observed for reactant-to-product laminar counterflow flames. Chemical explosive mode analysis was also performed to quantify the flame structure and local combustion mode. The diffusion–reaction balance in pinched-off flame islands favors extinction of these smaller structures, while auto-ignition modes are observed within the flame kernel after fresh mixture is engulfed and preheated in the product kernel. Statistics of the density-weighted displacement speed conditional on local combustion mode indicates strong correlation between the local extinction mode and negative displacement speed. The local balance between diffusion and reaction ultimately determines the propensity for local extinction in both laminar and turbulent flames, the extent of which has an impact on global flame propagation.

42 ENGINEERING↗
DOE OSTI2020

Numerical Investigation of Fuel Property Effects on Mixed-Mode Combustion in a Spark-Ignition Engine

In this research, lean mixed-mode combustion is numerically investigated using computational fluid dynamics (CFD) in a spark-ignition engine. A new E30 fuel surrogate is developed using a neural network model with matched octane numbers. A skeletal mechanism is also developed by automated mechanism reduction and by incorporating a NO x submechanism. A hybrid approach that couples the G-equation model and the well-stirred reactor model is employed for turbulent combustion modeling. The developed CFD model is shown to well predict pressure and apparent heat release rate (AHRR) traces compared with experiment. Two types of combustion cycles (deflagration-only and mixed-mode cycles) are observed. The mixed-mode cycles feature early flame propagation and subsequent end-gas auto-ignition, leading to two distinctive AHRR peaks. The validated CFD model is then employed to investigate the effects of NO x chemistry. The NO x chemistry is found to promote auto-ignition through the residual gas, while the deflagration phase remains largely unaffected. Sensitivity analysis is finally performed to understand effects of fuel properties, including heat of vaporization (HoV) and laminar flame speed (S L ). An increased HoV tends to suppress auto-ignition through charge cooling, while the impact of HoV on flame propagation is insignificant. In contrast, an increased S L is found to significantly promote both flame propagation and end-gas auto-ignition. The promoting effect of S L on auto-ignition is not a direct chemical effect; it is rather caused by an advancement of the combustion phasing, which increases compression heating of the end-gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Advanced Engine and Fuel Technologies Annual Progress Report (FY2019)

On behalf of the Vehicle Technologies Office of the U.S. Department of Energy, we are pleased to introduce the Fiscal Year (FY) 2019 Annual Progress Report for the Advanced Engine and Fuel Technologies Program. In support of the Vehicle Technology Office’s goal for future U.S. economic growth, the Program focuses on early-stage research and development to improve understanding of combustion processes, fuel properties, and emissions control technologies, generating knowledge and insight necessary for industry to cost-effectively develop the next generation of engines and fuels. One of the most promising and cost-effective approaches to improving the fuel economy of the U.S. vehicle fleet is to introduce the next generation of higher-efficiency, very-low-emission combustion engines that meet future federal emissions regulations into the passenger and commercial vehicle markets. Advanced fuel formulations that can incorporate non-petroleum-based blending agents could further enhance engine efficiency, reduce greenhouse gas emissions, and provide fuel diversification. Also, innovations in combustion, fuels, emissions control, air control, turbomachinery, and energy recovery could potentially increase fuel economy considerably compared to today’s vehicles. The expected national economic, environmental, and energy security benefits from these next-generation engines and fuels would be significant inasmuch as the majority of vehicles sold over the next several decades will still include an engine. The Program has set the following goals for passenger and commercial vehicle fuel economy improvements. By 2030, increase light-duty engine efficiency to demonstrate 35% improvement in passenger vehicle fuel economy (25% improvement from engine efficiency and 10% from fuel co-optimization) relative to a 2015 baseline vehicle, while meeting the U.S. Environmental Protection Agency Tier 3 Emission and Fuel Standards. By 2030, improve heavy-duty engine efficiency by 35% relative to a 2009 baseline vehicle and identify cost-effective high-performance fuels that can further increase efficiency up to an additional 4%, while meeting prevailing U.S. Environmental Protection Agency emissions standards. The Program utilized advanced combustion processes to increase engine efficiency, resulting in a modeled passenger vehicle fuel economy improvement of 19.4% (over a Model Year 2015 baseline) in FY 2019. This report highlights progress achieved by the Advanced Engine and Fuel Technologies Program during FY 2019. The nature, current focus, and recent progress of the Program are described together with summaries of National Laboratory, industry, and university projects that provide an overview of the exciting work being conducted to address critical technical barriers and challenges to commercializing the next generation of higher-efficiency engine, emissions control, and fuel technologies for passenger and commercial vehicles.

33 ADVANCED PROPULSION SYSTEMS↗