Search NASA⌕ Search

Engineering topics

Lu, Xingxu

Publications and source records attributed to Lu, Xingxu.

At least 19 records

Enhancing sorption kinetics by oriented and single crystalline array-structured ZSM-5 film on monoliths

Abstract To enhance the reaction kinetics without sacrificing activity in porous materials, one potential solution is to utilize the anisotropic distribution of pores and channels besides enriching active centers at the reactive surfaces. Herein, by designing a unique distribution of oriented pores and single crystalline array structures in the presence of abundant acid sites as demonstrated in the ZSM-5 nanorod arrays grown on monoliths, both enhanced dynamics and improved capacity are exhibited simultaneously in propene capture at low temperature within a short duration. Meanwhile, the ZSM-5 array also helps mitigate the long-chain HCs and coking formation due to the enhanced diffusion of reactants in and reaction products out of the array structures. Further integrating the ZSM-5 array with Co 3 O 4 nanoarray enables comprehensive propene removal throughout a wider temperature range. The array structured film design could offer energy-efficient solutions to overcome both sorption and reaction kinetic restrictions in various solid porous materials for various energy and chemical transformation applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ultrasmall Cu Nanoparticles Supported on Crystalline, Mesoporous ZnO for Selective CO 2 Hydrogenation

Converting CO 2 to value-added chemicals, e. g., CH 3 OH, is highly desirable in terms of the carbon cycling while reducing CO 2 emission from fossil fuel combustion. Cu-based nanocatalysts are among the most efficient for selective CO 2 -to-CH 3 OH transformation; this conversion, however, suffers from low reactivity especially in the thermodynamically favored low temperature range. We herein report ultrasmall copper (Cu) nanocatalysts supported on crystalline, mesoporous zinc oxide nanoplate (Cu@mZnO) with notable activity and selectivity of CO 2 -to-CH 3 OH in the low temperature range of 200–250 °C. Cu@mZnO nanoplates are prepared based on the crystal-crystal transition of mixed Cu and Zn basic carbonates to mesoporous metal oxides and subsequent hydrogen reduction. Under the nanoconfinement of mesopores in crystalline ZnO frameworks, ultrasmall Cu nanoparticles with an average diameter of 2.5 nm are produced. Cu@mZnO catalysts have a peak CH 3 OH formation rate of 1.13 mol h −1 per 1 kg under ambient pressure at 246 °C, about 25 °C lower as compared to that of the benchmark catalyst of Cu−Zn−Al oxides. In conclusion, our new synthetic strategy sheds some valuable insights into the design of porous catalysts for the important conversion of CO 2 -to-CH 3 OH.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Perovskite evolution on La modified Mn 1.5 Co 1.5 O 4 spinel through thermal ageing with enhanced oxidation activity: Is sintering always an issue?

Non-precious metal oxides have great potential in catalytic deep oxidation of emitted hydrocarbons to help address various environmental pollution concerns. However, sintering issue is a stumbling block in practical application upon long-term high-temperature operation or thermal shock experience. Herein, La was applied to modify Mn 1.5 Co 1.5 O 4 spinel to get a highly active oxidation catalyst with exceptional stability against high-temperature thermal ageing treatment. With thermal ageing at 750 °C for 100 h, the La modified Mn–Co composite reached 90 % conversion in toluene oxidation at 265 °C under the high WHSV of 120,000 mL g -1 h -1 , while this value increased to 312 °C over blank Mn–Co spinel. The addition of La not only inhibited the growth of spinel nanocrystals, but also brought about perovskite formation through sintering, generating perovskite-spinel interfaces, thus enhancing both activity and stability. Meanwhile, the La modified Mn–Co spinel exhibited superior performance in presence of water or sulfur dioxide after thermal ageing treatment. In conclusion, this work offers a versatile strategy to design anti-sintering and active oxidation nanocatalysts based on non-precious metal oxides for industrial applications.

36 MATERIALS SCIENCE↗

Unraveling Anisotropic and Pulsating Etching of ZnO Nanorods in Hydrochloric Acid via Correlative Electron Microscopy

Despite much technical progress achieved so far, the exact surface and shape evolution during wet chemical etching is less unraveled, especially in ionically bonded ceramics. Herein, by using in situ liquid cell transmission electron microscopy, a repeated two-stage anisotropic and pulsating periodic etching dynamic is discovered during the pencil shape evolution of a single crystal ZnO nanorod in aqueous hydrochloric acid. Specifically, the nanopencil tip shrinks at a slower rate along [0001̅] than that along the $\langle$101̅0$\rangle$ directions, resulting in a sharper ZnO pencil tip. Afterward, rapid tip dissolution happens due to accelerated etching rates along various crystal directions. Concurrently, the vicinal base region of the original nanopencil tip emerges as a new tip followed by the repeated sequence of tip shrinking and removal. The high-index surfaces, such as {101̅m} (m = 0, 1, 2, or 3) and {21̅1̅n} (n = 0, 1, 2, or 3), are found to preferentially expose in different ratios. Our 3D electron tomography, convergent beam electron diffraction, middle-angle bright-field STEM, and XPS results indicate the dissociative Cl – species were bound to the Zn-terminated tip surfaces. Furthermore, DFT calculation suggests the preferential Cl – passivation over the {101̅1} and (0001) surfaces of lower energy than others, leading to preferential surface exposures and the oscillatory variation of different facet etching rates. The boosted reactivity due to high-index nanoscale surface exposures is confirmed by comparatively enhanced chemical sensing and CO 2 hydrogenation activity. In conclusion, these findings provide an in-depth understanding of anisotropic wet chemical etching of ionic nanocrystals and offer a design strategy for advanced functional materials.

36 MATERIALS SCIENCE↗

Optimization and understanding of ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst for enhanced CO 2 -methanol conversion at low temperature and pressure

Cu-ZnO-Al 2 O 3 is the most widely applied catalyst for CO 2 hydrogenation to methanol. However, it is still a challenge to produce methanol using this catalyst under low-temperature (<250 °C) and low-pressure (<10 bar) conditions with desirable yield and selectivity. In this work, by tuning the experimental processing parameters such as solvent, loading amount, and annealing temperature, highly improved ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalysts have been successfully demonstrated. Here, by using organic solvent (N,N-dimethylformamide (DMF), acetone, or isopropanol) for dip-coating loading process instead of deionized (DI) water, Cu-ZnO-Al 2 O 3 nanocatalysts was comparatively better dispersed on the nanorod array support with populated and abundant active sites, thus enhancing the methanol yield. With the control of the loading amount and annealing temperature, finely distributed Cu nanoparticles were obtained on the ZnO nanorod surfaces to enhance the interactions between Cu and ZnO nanorod surfaces. Further improvement of the catalyst performance is demonstrated by tuning the reaction space velocity. At 200 °C and 10 bar conditions, the optimized catalyst achieved a methanol yield of 6.46 mol h –1 kg –1 with 100 % selectivity. The good stability after prolonged testing of the catalysts demonstrates the potential practical implementation. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) measurements under the 1 bar reveal that the CO 2 hydrogenation to methanol on the ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst follows the CO reaction pathway, due to the surface oxygen vacancies on ZnO nanorods which facilitate CO 2 dissociation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Microwave assisted and low-temperature fabrication of nanowire arrays on scalable 2D and 3D substrates

A method of making a titanium dioxide nanowire array includes contacting a substrate with a solvent comprising a titanium (III) precursor, an acid, and an oxidant while microwave heating the solvent, thereby forming a hydrogen titanate H2Ti2O5.H2O nanowire array. The hydrogen titanate nanowire array is annealed to form a titanium dioxide nanowire array. The substrate is seeded with titanium dioxide before starting the hydrothermal synthesis of the hydrogen titanate nanowire array. The titanium dioxide nanowire array is loaded with a platinum group metal to form an exhaust gas catalyst. The titanium dioxide nanowire array can be used to catalyze oxidation of combustion exhaust.

Gao, Pu-Xian↗

Synergistic promotion of transition metal ion-exchange in TiO 2 nanoarray-based monolithic catalysts for the selective catalytic reduction of NO x with NH 3

TiO 2 supported catalysts have been widely studied for the selective catalytic reduction (SCR) of NO x ; however, comprehensive understanding of synergistic interactions in multi-component SCR catalysts is still lacking. For this work, transition metal elements (V, Cr, Mn, Fe, Co, Ni, Cu, La, and Ce) were loaded onto TiO 2 nanoarrays via ion-exchange using protonated titanate precursors. Amongst these catalysts, Mn-doped catalysts outperform the others with satisfactory NO conversion and N 2 selectivity. Cu co-doping into the Mn-based catalysts promotes their low-temperature activity by improving reducibility, enhancing surface Mn 4+ species and chemisorbed labile oxygen, and elevating the adsorption capacity of NH 3 and NO x species. While Ce co-doping with Mn prohibits the surface adsorption and formation of NH 3 and NO x derived species, it boosts the N 2 selectivity at high temperatures. By combining Cu and Ce as doping elements in the Mn-based catalysts, both the low-temperature activity and the high-temperature N 2 selectivity are enhanced, and the Langmuir–Hinshelwood reaction mechanism was proved to dominate in the trimetallic Cu–Ce–5Mn/TiO 2 catalysts due to the low energy barrier.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Transition-metal doped titanate nanowire photocatalysts boosted by selective ion-exchange induced defect engineering

Defect engineering through elemental doping is an efficient way to boost the performance of semiconductor photocatalysts. For this work, transition-metal (TM) doped titanate nanowires (TNWs) were prepared via ion-exchange over the titanate precursors and demonstrated for the Rhodamine B (RhB) degradation under ultraviolet (UV) light irradiation. The ion-exchange of selective ions (V 5+ , Cr 3+ , Ni 2+ , and Zn 2+ ) with protons from pristine TNWs resulted in the hierarchical meso-porosity of nanowires with large pores of ~5–20 nm by TM doping and small pores of ~3.6–4.5 nm inherited from pristine TNWs, which facilitates the mass transfer while maintaining high surface area and active sites. Meanwhile, the TM intercalation partially reduces the Ti 4+ to Ti 3+ and narrows the optical bandgap, which, together with oxygen vacancies and superoxide radicals from pristine TNWs, enhance the adsorption and photocatalytic degradation performance of RhB. This work helps to elucidate the effects of transition-metal doping and provides a rational strategy towards high performance titanate-based photocatalysts for efficient and sustainable wastewater treatment.

36 MATERIALS SCIENCE↗

Mass transport in nanoarray monolithic catalysts: An experimental-theory study

Reducing the mass transfer resistance globally of a catalyst is a key to enhancing the catalytic reaction kinetics and fully utilizing the catalyst activity. Despite the success in tailoring the external mass transfer in the widely studied washcoat monoliths, the internal mass transfer resistance is difficult to be reduced due to the requirement of increasing macroporosity while maintaining high specific surface area and mechanical stability. Therefore, nanostructured array-based monolithic catalysts (nanoarray catalysts) have been developed in the past decade as a promising class of structured catalysts that may complement or substitute washcoat catalysts. This work fundamentally elucidates the enhanced mass transport properties of the nanoarray monolithic catalysts by a combination of experimental measurements and theoretical modeling. Using a low-dimensional model, the relative contributions of resistances were quantified in terms of chemical kinetics, internal and external mass transfers based on a probe model of C2H4 oxidation over the TiO2 supported Pt-based monolithic catalysts. The nanoarray catalysts displayed a lower internal mass transfer resistance than the washcoat counterparts as a result of the high macroporosity and small thickness of nanoarray layers. Finally, the nanoarray configuration provides a new pathway towards designing high-performance monolithic reactors and catalysts with low internal diffusion limitations for various gas phase reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synergistic catalysis by Mn promoted ceria for molecular oxygen assisted epoxidation

Mesoporous manganese doped cerium oxide catalysts were prepared by an inverse micelle method with different manganese loadings. These materials exhibited superior activity for epoxidation of alkenes with molecular oxygen. Highest active 10MnCe material showed an activity of 80 % conversion and >99 % selectivity for cyclooctene epoxidation. The fluorite crystal structure which facilitates the high oxygen mobility, low temperature reducibility, homogeneous distribution of manganese on ceria, nanoparticle nature, higher number of oxygen vacancies, low valent states of manganese and cerium, and the ability to generate reactive oxygen species of the manganese doped cerium oxide could be correlated to the high catalytic activity. The reaction followed first order kinetics with a rate constant of 0.31 h –1 at 100 °C, and the activation energy turned out to be 10.5 kJ/mol. In conclusion, the mechanistic study revealed that the reaction proceeds via a unique mechanism which involves in situ generated superoxide and singlet oxygen species..

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhancing ZnO nanowire gas sensors using Au/Fe 2 O 3 hybrid nanoparticle decoration

Heterojunctions are an important strategy for designing high performance electrical sensor materials and related devices. Herein, a new type of metal-semiconductor hybrid nanoparticle has been successfully used to remarkably sensitize the surface of ZnO nanowires for detecting NO 2 with high responses over a broad temperature window ranging from room temperature to 600 °C. These hybrid nanoparticles are comprised of iron oxide nanowires with well dispersed single crystalline Au nanoparticles. The hybrid nanoparticle decorated ZnO nanowires have achieved a giant response, as high as 74 500 toward NO 2 gas, about 42 times that of Au decorated ZnO nanowire sensors. This dramatic enhancement may be attributed to the efficient charge transfer across the Au–Fe 2 O 3 Schottky and Fe 2 O 3 –ZnO semiconductor heterojunction interfaces. Due to the incorporation of thermally-stable Fe 2 O 3 nanoparticles as the support of Au nanoparticles, the working temperature of nanowire sensors was successfully extended to higher temperatures, with an increase of 200 °C, from 400 °C to 600 °C. Such a combination of semiconductor heterojunction and semiconductor-metal Schottky contact presents a new strategy for designing high performance electrical sensors with high sensitivity, stability, selectivity, and wide operation temperature window, which are potentially suitable for advanced energy systems such as automotive engines and power plants.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Perovskite-sensitized β-Ga 2 O 3 nanorod arrays for highly selective and sensitive NO 2 detection at high temperature

Amongst various gaseous pollutants, NO 2 is one of the major exhausts originating from fossil fuel and gas combustions in vehicle engines and power plants at high temperature. Under such a scenario, in situ and real-time gas detection and monitoring solutions are largely limited, which hinders the energy-efficient and resource-saving operations of these advanced energy systems. Herein, a new type of perovskite-sensitized β-Ga 2 O 3 nanorod-array has been successfully fabricated to detect NO x at high temperature selectively and sensitively. The demonstrated gas sensors are highly sensitive to NO 2 at 800 °C, with excellent reversible and reproducible response characteristics. Through the surface decoration of perovskite-type La 0.8 Sr 0.2 CoO 3 (LSCO) nanoparticles, the sensitivity of β-Ga 2 O 3 nanorod array gas sensors is enhanced by nearly an order of magnitude, along with much faster response dynamics. A remarkable selectivity toward oxidative gases was also demonstrated with the robust differentiation of NO 2 .

36 MATERIALS SCIENCE↗

Solvent effects on the heterogeneous growth of TiO 2 nanostructure arrays by solvothermal synthesis

One-dimensional titanium dioxide (TiO 2 ) nanostructure arrays (nanoarrays) are important metal oxide nanomaterials that can be synthesized via facile solvothermal methods. The properties of the organic solvents can impose significant effects on the microstructures and properties of the final products. However, the discussions were limited to the homogeneously nucleated TiO 2 nanomaterials in free-standing powder form, while the solvent effects are less understood during the heterogeneous growth of TiO 2 nanoarrays on a substrate surface. In this work, six organic compounds, namely 2-butanone, n-decane, n-hexane, toluene, ethylene glycol and ethanol, were selected as the solvents for the solvothermal synthesis of TiO 2 nanoarrays on the cordierite monolithic substrates. Special attentions are paid to the morphology, crystallinity, specific surface area, and porosity of the samples. The heterogeneous growth of TiO 2 nanoarrays on substrate surfaces is found to favor the solvents with moderate dielectric constants, which can be partially dissolved in the aqueous solution and modulate the reaction rate during the solvothermal synthesis. Organic solvents with low dielectric constants may result in a complete separation between the precursors and aqueous solution, and therefore slow down the overall reaction, causing the insufficient growth of the nanoarrays. The TiO 2 nanoarrays are obtained with optimum morphology from the combination of 2-butanone and titanium (IV) butoxide as solvent and precusor, respectively, with a high specific surface area up to 56 m 2 /g including cordierite substrate given a micron thickness. When loaded with Pt catalyst, the TiO 2 nanoarray-based monolithic catalysts show excellent low-temperature catalytic activity and hydrothermal stability for the CO and hydrocarbon oxidation under the simulated exhausted conditions. This article shall shed light on a better understanding of the growth mechanism and rational design of TiO 2 nanoarrays for high-performance catalytic converters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Activating low-temperature diesel oxidation by single-atom Pt on TiO 2 nanowire array

Supported metal single atom catalysts (SACs) present an emerging class of low-temperature catalysts with high reactivity and selectivity, which, however, face challenges on both durability and practicality. Herein, we report a single-atom Pt catalyst that is strongly anchored on a robust nanowire forest of mesoporous rutile titania grown on the channeled walls of full-size cordierite honeycombs. This Pt SAC exhibits remarkable activity for oxidation of CO and hydrocarbons with 90% conversion at temperatures as low as ~160 °C under simulated diesel exhaust conditions while using 5 times less Pt-group metals than a commercial oxidation catalyst. Such an excellent low-temperature performance is sustained over hydrothermal aging and sulfation as a result of highly dispersed and isolated active single Pt ions bonded at the Ti vacancy sites with 5 or 6 oxygen ions on titania nanowire surfaces.

36 MATERIALS SCIENCE↗

Solar-driven efficient methane catalytic oxidation over epitaxial ZnO/La 0.8 Sr 0.2 CoO 3 heterojunctions

Gas flaring in oil/gas drilling and gas leakage in natural gas power plant lead to significant energy loss and environmental burden. Here, solar-driven efficient methane oxidation was demonstrated under high velocity continuous flow over the ZnO/La 0.8 Sr 0.2 CoO 3 (ZnO/LSCO) heterojunctions. The ZnO/LSCO heterojunctions enable a unique epitaxial hetero-interface, which effectively regulates the electron transfer between Zn 3d -O 2p hybrid orbital in ZnO and Co e g orbital in LSCO and promotes the rapid generation and refill of oxygen vacancy with unpaired electron (V o ), thus enhancing the activity and mobility of surface lattice oxygen in ZnO/LSCO. Under solar illumination, the synergy of photothermal and photocatalytic effect boosts the reversible electron transfer in the interface, which further activates surface lattice oxygen, resulting in a ~2 times higher methane oxidation activity. Such a solar-driven system not only enables a promising pathway for emitted methane utilization, but also provides an advanced catalyst design concept of epitaxial interface construction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗