Engineering topics

Lu, Yunxing

Publications and source records attributed to Lu, Yunxing.

6 records

DOE OSTI2024

Utah FORGE 2-2446: Closing the Loop Between In-Situ Stress Complexity and EGS Fracture Complexity - 2024 Annual Workshop Presentation

This is a presentation on Closing the Loop Between In-Situ Stress Complexity and EGS Fracture Complexity by Lawrence Livermore National Laboratory, presented by Matteo Cusini. The video discusses the combination of high-fidelity simulations and true-triaxial block fracturing tests to explore the intricate relationship between in-situ stress and hydraulic fracture patterns. This presentation was featured in the Utah FORGE R&D Annual Workshop on August 14, 2024.

15 GEOTHERMAL ENERGY↗

DOE OSTI2023

Go/No-Go Decision Point 1 Report

To satisfy the G/NG point 1 we have employed GEOS hydraulic fracturing module to simulate one of the Diagnostic Fracture Injection Tests conducted at well 58-32. The hydraulic fracturing solver relies on a finite element discretization of the mechanics fully coupled to a finite volume discretization of the fluid flow. Fractures are explicitly modeled as lower dimensional manifolds and discretized by 2D elements sitting at the boundary of cell elements. We have calibrated our model to reproduce the DFIT corresponding to Zone 2 Cycle 4 of the injection tests that took place at well 58-32.

15 GEOTHERMAL ENERGY↗

DOE OSTI2023

Prediction and demonstration of periodic tensile cracking in rate-dependent porous cement

Periodic dilation bands are shown to occur when cylinder-shaped saturated cement specimens are subjected to rapid decompression, with the spacing between the bands scaling as a power law of the decompression time. This behavior is predicted by theory, which is specified to this scenario based on prior work that was more general and applied to compaction. Specifically, the formation of the bands is shown to coincide with periodicity that naturally arises in the effective stress when the material follows a Terzaghi-type consolidation law, although in reverse for dilation and with material deformation described by a rate-dependent viscoplastic law. When strain rate is proportional to effective stress to a power that is greater than one, periodic regions of tensile effective stress arise through the poromechanical fluid-solid coupling. The theoretically-predicted exponent of the resulting power-law relationship between dilation band spacing and unloading time successfully brackets the experimental results, for which it is observed that the exponent is slightly stronger than a square-root relationship (0.28 to 0.67) at testing temperatures of 20 °C and 90 °C. Further, these results demonstrate that rapid-depressurization leads to periodic fracturing that could, on the one hand, be detrimental to the isolation provided by cement used to seal wellbores in the petroleum industry. On the other hand, the dilation bands could also be favorable to production if generated in low-permeability reservoir rocks such as shales that are targeted for petroleum production or granites that are targeted for geothermal energy.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Graphene nanoplatelets reinforced cement as a solution to leaky wellbores reinforcing weak points in hydrated Portland cement with graphene nanoparticles improves mechanical and chemical durability of wellbore cements

In this work, to improve the performance of wellbore cement under subsurface environments, graphene nanoplatelets (GNPs) were added in various percentages to Class-H cement slurry. Microstructural characterization of cement slurries cured at 90 °C and 95% RH indicates that GNP modifies the microstructure of hydrated cement by reinforcing pore spaces. As a result, the mechanical properties, such as Young's modulus and axial peak stress, obtained from high temperature triaxial compression tests are significantly improved based on different percentages of added GNPs. Furthermore, the hydrated 1 × 2 inch GNP- Portland cement cores tested under simulated deep wellbore conditions of high-temperature and high pressure (HTHP), appear to have a ductile-like behavior, when compared to a typical brittle nature of Portland cement pastes. From our observations and published data on graphene resistance to fracture, GNP addition to cement is evidently enhancing the flexibility of cement. These improvements would reduce the risks associated with wellbore cement deterioration and a consequent leakage in fossil fuel production, geothermal energy production, CO 2 storage as well as long-term sealing materials in plugging and abandonment of all wellbores at the end of their service life.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Mechanical Properties of Nominally Ductile and Brittle Zones within the Caney Shale Formation

We present a case study from the Caney Shale, which is an emerging hydrocarbon-bearing formation in Oklahoma. Open hole logs lead to a nominal distinction of five zones in an exploration well, two of which are designated “ductile” and three of which are designated as less ductile “reservoir” zones. Subsequently, a detailed mechanical characterization was carried out on core plugs taken from each of these zones. Results show nominally “ductile” zones are weaker in terms of UCS, tensile strength, fracture toughness, and confined compressive strength. However, by a variety of brittleness indices, it is found the nominal “ductile” regions do not behave as expected. They are weaker, but not consistently more ductile. Furthermore, some brittleness indices lead to contradictory conclusions. For example, zones which would be considered the most brittle according to the proportion of nonlinear stress-strain behavior prior to failure and/or by indices based on elastic properties would be considered the least brittle according to their internal friction angle.

Benge, Margaret↗

DOE OSTI2021

Connecting Geomechanical Properties with Potential for Proppant Embedment and Production Decline for the Emerging Caney Shale, Oklahoma

The Caney Shale is emerging as a target for hydrocarbon production, creating opportunities to study rock mechanical origins of observed/anticipated challenges to effective and sustained stimulation. Here we examine five subunits within the Caney, two of which are dubbed “ductile” and three of which are dubbed “reservoir” rock types. The “ductile” versus “reservoir” identification is initially based on elastic properties ascertained from well logs. By comparing core-based mechanical tests, it is found nominally ductile and reservoir layers do not differ in terms of brittleness, but instead the nominally ductile layers tend to be weaker and more prone to creep deformation compared to the nominally more brittle reservoir layers. This difference in mechanical properties is shown to generate higher susceptibility to proppant embedment in the weaker and more creep-prone layers. Specifically, over a 5-year period, the creep is expected to have little impact on reservoir layers but is predicted to reduce propped fracture aperture by a factor of 2 in the ductile layers.

Benge, Margaret↗