Search NASA⌕ Search

Engineering topics

Luitjohan, Kara Eileen

Publications and source records attributed to Luitjohan, Kara Eileen.

Uranium Processing Signatures for Nuclear Forensics (NA22 End of FY23 Report)

A vacuum induction melting (VIM) furnace was used to produce an ~120 kg depleted uranium (DU) rod in November 2021 from well characterized feedstock to investigate the separation of thorium (Th) and protactinium (Pa) from uranium (U) during U metal casting and quantify the behavior of the 230 Th/ 234 U and 231 Pa/ 235 U radiochronometry systems. This work suggested that while 234 Th, measured by gamma spectrometry, appears to segregate to the top and surface of the rod, the concentration of 230 Th determined by isotope dilution mass spectrometry (IDMS) in drill turnings from multiple locations in the rod, including the hot top, is relatively consistent. To evaluate whether Th is potentially enriched at only the very outer surface of the cast DU rod relative to the bulk material in the cast rod, thin surface samples were collected from the cast DU rod. Locations sampled included the inner diameter (ID) and outer diameter (OD) of the bottom of the casting and the ID, OD, and top face of the hot top (very top of the casting). The locations are shown in Figure 1. Four samples were taken from each location at different depths in the cast material. Each cut took approximately 0.03 – 0.05” off of the casting.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Investigation of Carbide Inclusions in Cast Uranium [Slides]

Outline - Introduction: The motivations for the project, and some background on inclusions in uranium, and about the samples; Lath Inclusion Morphology: Looking at the morphology of a specific family of carbide inclusions in casting 20; Clustering of Lath Inclusions: Investigating the group behavior of these lath shaped inclusions from the inner to outer edges; Conclusions: Final thoughts on the lath inclusions and future work ideas.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Results from a controlled depleted uranium metal casting experiment designed to investigate nuclear Forensic Radiochronometry Signatures

The accurate interpretation of uranium metal 230 Th/ 234 U and 231 Pa/ 235 U radiochronometry model ages requires an understanding of how uranium parent nuclides and decay progeny ( 230 Th and 231 Pa) behave during uranium metal casting. In order to directly measure the spatial distribution of 230 Th and 231 Pa in uranium metal before and after vacuum induction melting (VIM), Los Alamos National Laboratory identified uranium metal feedstock, characterized the metal feedstock, conducted a controlled casting experiment of an approximately 120 kg uranium metal rod, and characterized the cast metal. Herein this study presents radiochronometry results and quantified 230 Th and 231 Pa VIM separation factors from bulk uranium.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

U-rich U-Mo Solidus, Liquidus, Enthalpy, and Thermal Diffusivity

Several material properties have been studied as a function of composition as part of the USHPRR effort to use U-10Mo for LEU monolithic fuel foils, with special attention to areas where simulation outcomes can be improved. The liquidus and solidus phase boundaries are important for engineering design of processing parameters and for predicting the degree of microsegregation within initial castings. The numerous phase diagram constructions available in the literature differ significantly in their solid/liquid boundary definitions, therefore, an experimental strategy was employed in order to resolve some of the discord. That strategy focuses not on proving any singular point, but instead to provide data with highly characterized uncertainty. The data presented here is the most consistent with the U-rich liquidus and solidus boundaries provided by H. Okamoto (2012), Berche et al. (2011), and Mardon et al. (1959). The recently suggested change in the peritectic reaction temperature (to 1302 K) suggested by Berchè and adopted by Okamoto is also supported, but with lower confidence. The enthalpy of fusion is a basic characteristic of the solidification reaction property for which is required for both research-oriented predictions of behavior and development of applied design strategies for casting engineering. It has been determined that an admixture model for the heat of fusion between U BCC and Mo BCC is a reasonable assumption within the composition region of interest, though limitations of the measurement accuracy impacts the ability to support any trends more detailed than this baseline behavior. A limited number of thermal diffusivity measurements were also performed into the gamma region to provide additional information for solidification modeling and simulations as well as a check on the component properties of thermal conductivity, density, and heat capacity.

36 MATERIALS SCIENCE↗

Intentional Uranium Tagging for Material Provenance and Pathway Forensics (LA19-Intentional-Forensics-NDD3Bb): Final Project Report

This report summarizes the outcomes of a 3-year NA-22 exploratory project to research the feasibility of tagging uranium materials, especially nuclear fuels, for nuclear nonproliferation purposes. The experimental focus was on metallic uranium forms under prospective surface and bulk tagging manufacturing and detection scenarios. This study showed that a large number of tags (drawn from an even larger menu of options) could be successfully imparted and detected in both as-built and degraded conditions. These results pave the way for additional R&D studies of surface and bulk tagging of metallic forms of uranium.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Intentional Uranium Tagging for Material Provenance and Pathway Forensics (LA19-Intentional-Forensics-NDD3Bb) (Annual Report for FY21)

This report describes the outcomes of the third and final year of a project to research the feasibility of tagging uranium materials, especially nuclear fuels. The experimental focus remained on metallic uranium forms under prospective surface and bulk tagging scenarios. Overall, the results showed that the tags could be successfully imparted and characterized in both as-built and degraded conditions. This was in line with expectations coming into this project, indicating promise for both surface and bulk tagging of metallic forms of uranium. Multiple surface tagging techniques and detection strategies were explored in FY21, with an emphasis on improving tag quality, readability, and detection in the field. Non-radioactive materials were used as a testbed. Selective deposition via laser beam was determined to be successful in imparting a readable titanium deposit on a stainless steel base plate, and can be read with high resolution characterization techniques (e.g., scanning electron microscopy) and field capable tools (e.g., eddy current testing). Other deposition techniques, such as selective deposition via electron beam and photoluminescent tags, were explored in FY21, and while success for these techniques would be dependent on additional work, these techniques showed potential for surface tagging applications. To survey bulk taggant elements for bulk uranium metal, 16 tagging elements were spread among 18 depleted uranium castings (4 baseline, 3 mix, 1 dilution, and 10 recycle). Most of these were made and characterized in FY21. Taggant acceptability was based upon manufacturability, detectability, and persistence from the standpoint of two detection options: bulk chemical analysis (for “chemical taggants”) and microstructural analysis (for “second phase taggants”). Taggant detection in both up-front manufacturing and in the face of “degradations” such as dilution, mixing, and recycling was generally good. Two independent laboratories carried out chemical analysis on most of the castings, and often at several locations within a casting, and the results are discussed. Scanning electron microscopy+EDS microanalysis revealed the second phases mostly contained the expected tagging elements. The shapes and 2 spatial distributions of these micron-sized carbides, oxides, and intermetallic particles offers opportunities for further science-based investigation and tagging optimization. Overall, V and Co currently appear as the best choices for chemical taggants while Al, Ti, Mn, Co, Pd, and Tb all look good as second phase taggants. The other elements considered here – Sc, Ni, Ge, Nb, Ce, Ta, W, Ir, and Au – while not being ruled out, require more study to become viable options. It is of special note that in the recycling study only one of the 12 elements fell out of detection even after 10 meltings, demonstrating their persistence. An Appendix tabulates all chemical analysis results to enable more quantitative and statistical studies of detection opportunities and limitations, as a part of a related project.

36 MATERIALS SCIENCE↗

Microwave Cast Material Examination

Microwave-cast material dating from the latest prototype development period and subsequent TRL 7 advancement testing was sent to LANL for additional characterization. The initial characterization described here is considered a supplement to and verification of that performed by Y-12 during the Technology Readiness Assessment process. The carbon chemistry results from Y-12 and LANL regarding early prototype microwave cast test object (CTO) and cylinder castings match within expectations. Only one fully intact as-cast CTO was available for examination in which carbon chemistry does not appear to vary spatially, at least at relatively low carbon levels (hypoeutectic). The large as-cast grain size leads to relatively poor grain size statistics and similar difficulties were encountered during the TRA. Small, isolated gas pores were observed in four of the five metallographic samples in prototype CTO casting PT-01. Finally, the next phase of characterization work, which focuses on corrosion behavior, has started and is described briefly.

36 MATERIALS SCIENCE↗

Effect of Solute Elements on Boron Segregation in Boron-Containing Steels

The addition of boron to steel alloys results in an increase in both hardenability and casting defects. The casting difficulties are predicted to stem from a metatectic reaction, δ + γ → L + γ, where a fully solidified material begins to locally remelt as the temperature decreases. Another possible source of casting defects is a boride-rich phase that is predicted to remain liquid at low temperatures. To experimentally determine which reaction is the likely source of the casting defects, the predicted reactions and the effect of solute elements on those reactions are investigated. Levitation zone melting is used to control segregation in a ternary Fe–C–B alloy and a commercial 22MnB5 alloy. Carbon segregation and a peritectic reaction result in a peritectic jump during directional solidification where the first directionally solidified (DS) zone undergoes δ-bcc solidification followed by a peritectic jump to steady state planar solidification of γ-fcc in the second DS zone. The presence of other solute elements in the zone melted 22MnB5 alloy lead to a breakdown in the planar solidification front before steady state solidification could be achieved in the second DS zone. With a cellular solid/liquid interface, boron-rich intercellular liquid formed low melting iron boro-carbide particles. The controlled solidification conditions in a levitation zone melter were unable to prevent ~0.003 wt% boron from segregating to high enough levels to form boride particles. Therefore, it is likely that during commercial casting, the formation of the low melting boride phase from interdendritic segregation is a key source of the casting issues.

36 MATERIALS SCIENCE↗

FY18 Report: HFIR Fuel Casting Support and Microstructural Feature Examination

An effort to commence conversion of the High Flux Isotope Reactor (HFIR) to a low enriched uranium (LEU) based fuel has been proposed. While recent experience from LEU-10wt%Mo (U-10Mo) monolithic metal fuel production may be leveraged considerably, the significant differences between research fuels requires some degree of strategy reassessment. In that spirit, initial casting trials have been performed at LANL over the last two years in order develop a high quality starting metal ingot.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗