Search NASA⌕ Search

Engineering topics

Luo, Jian

Publications and source records attributed to Luo, Jian.

At least 19 records

Creep and failure at metal-oxide interfaces

Small-scale bicrystal creep experiments were performed on contacts formed via in situ high-temperature diffusion bonding of metal-oxide interfaces including Ag-ZrO 2 , Pd-ZrO 2 , Pt-ZrO 2 , and Ag-high entropy oxide. This work characterizes deformation and failure at metal-oxide interfaces during mechanical loading. Interfacial sliding can be activated easily, while tensile interfacial creep was not observed at any condition of stress or temperature measured. Plastic strain, instead, localizes within the metal under tensile loading. A variety of mechanisms for plastic strain occur in the metal including lattice dislocation-mediated plasticity, twinning, low-angle grain boundary formation, and low-angle grain boundary creep. Surface and low-angle grain boundary diffusion occur under conditions where no metal-oxide tensile creep is observed, highlighting the significant differences in their interfacial mechanical response. High-temperature interfacial failure occurs when the mean curvature at the contact neck is approximately zero and the applied stresses comparable to brittle fracture stresses. The brittle fracture stresses were measured to be σ ƒ = 180 ± 90 MPa at the Ag-ZrO 2 interface at 225 °C, σ ƒ = 460 ± 160 MPa at the Pd-ZrO 2 interface at 680 °C, and σ ƒ = 640 ± 440 MPa at the Pt-ZrO 2 interface at 1010 °C.

Creep↗

Cation Vacancies Enable Anion Redox in Li Cathodes

Conventional Li-ion battery intercalation cathodes leverage charge compensation that is formally associated with redox on the transition metal. Employing the anions in the charge compensation mechanism, so-called anion redox, can yield higher capacities beyond the traditional limitations of intercalation chemistry. Here, we aim to understand the structural considerations that enable anion oxidation and focus on processes that result in structural changes, such as the formation of persulfide bonds. Using a Li-rich metal sulfide as a model system, we present both first-principles simulations and experimental data that show that cation vacancies are required for anion oxidation. First-principles simulations show that the oxidation of sulfide to persulfide only occurs when a neighboring vacancy is present. To experimentally probe the role of vacancies in anion redox processes, we introduce vacancies into the Li 2 TiS 3 phase while maintaining a high valency of Ti. When the cation sublattice is fully occupied and no vacancies can be formed through transition metal oxidation, the material is electrochemically inert. Upon introduction of vacancies, the material can support high degrees of anion redox, even in the absence of transition metal oxidation. The model system offers fundamental insights to deepen our understanding of structure–property relationships that govern reversible anion redox in sulfides and demonstrates that cation vacancies are required for anion oxidation, in which persulfides are formed.

25 ENERGY STORAGE↗

First Principles Study of Aluminum Doped Polycrystalline Silicon as a Potential Anode Candidate in Li‐ion Batteries

Addressing sustainable energy storage remains crucial for transitioning to renewable sources. While Li‐ion batteries have made significant contributions, enhancing their capacity through alternative materials remains a key challenge. Micro‐sized silicon is a promising anode material due to its tenfold higher theoretical capacity compared to conventional graphite. However, its substantial volumetric expansion during cycling impedes practical application due to mechanical failure and rapid capacity fading. A novel approach is proposed to mitigate this issue by incorporating trace amounts of aluminum into the micro‐sized silicon electrode using ball milling. Density functional theory (DFT) is employed to establish a theoretical framework elucidating how grain boundary sliding, a key mechanism involved in preventing mechanical failure is facilitated by the presence of trace aluminum at grain boundaries. This, in turn, reduces stress accumulation within the material, reducing the likelihood of failure. To validate the theoretical predictions, capacity retention experiments are conducted on undoped and Al‐doped micro‐sized silicon samples. In conclusion, the results demonstrate significantly reduced capacity fading in the doped sample, corroborating the theoretical framework and showcasing the potential of aluminum doping for improved Li‐ion battery performance.

25 ENERGY STORAGE↗

Manganese-based A-site high-entropy perovskite oxide for solar thermochemical hydrogen production

Non-stoichiometric perovskite oxides have been studied as a new family of redox oxides for solar thermochemical hydrogen (STCH) production owing to their favourable thermodynamic properties. However, conventional perovskite oxides suffer from limited phase stability and kinetic properties, and poor cyclability. Here, we report a strategy of introducing A-site multi-principal-component mixing to develop a high-entropy perovskite oxide, (La 1/6 Pr 1/6 Nd 1/6 Gd 1/6 Sr 1/6 Ba 1/6 )MnO 3 (LPNGSB_Mn), which shows desirable thermodynamic and kinetics properties as well as excellent phase stability and cycling durability. LPNGSB_Mn exhibits enhanced hydrogen production (~77.5 mmol mol oxide -1 ) compared to (La 2/3 Sr 1/3 )MnO 3 (~53.5 mmol mol oxide -1 ) in a short 1 hour redox duration and high STCH and phase stability for 50 cycles. LPNGSB_Mn possesses a moderate enthalpy of reduction (252.51–296.32 kJ (mol O) -1 ), a high entropy of reduction (126.95–168.85 J (mol O) -1 K -1 ), and fast surface oxygen exchange kinetics. All A-site cations do not show observable valence changes during the reduction and oxidation processes. In conclusion, this research preliminarily explores the use of one A-site high-entropy perovskite oxide for STCH.

08 HYDROGEN↗

Compositional inhomogeneity and its effect on the hardness of nanostructured refractory high-entropy alloys

The pronounced compositional inhomogeneity observed in refractory high-entropy alloys (HEAs), as opposed to non-refractory HEAs, has an important influence on their mechanical properties, thereby posing a significant challenge for the development of high-performance refractory HEAs. In this work, by combining transmission electron microscopy imaging, chemical analysis, and nano-hardness tests, we investigate the compositional inhomogeneities in a series of sintered nanostructured HEAs and elucidate their influence on the material's hardness. Further, we reveal that the compositional inhomogeneity of the sintered nanostructured HEAs is temperature- and component- dependent. By correlating the hardness of nanostructured HEAs to the evolving compositional inhomogeneity, our work demonstrates that the compositional inhomogeneity in nanostructured HEAs can be tuned by sintering temperature or alloying towards optimized microstructure and hardness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A stable atmospheric-pressure plasma for extreme-temperature synthesis

Plasmas can generate ultra-high-temperature reactive environments that can be used for the synthesis and processing of a wide range of materials. However, the limited volume, instability and non-uniformity of plasmas have made it challenging to scalably manufacture bulk, high-temperature materials. Here we present a plasma set-up consisting of a pair of carbon-fibre-tip-enhanced electrodes that enable the generation of a uniform, ultra-high temperature and stable plasma (up to 8,000 K) at atmospheric pressure using a combination of vertically oriented long and short carbon fibres. The long carbon fibres initiate the plasma by micro-spark discharge at a low breakdown voltage, whereas the short carbon fibres coalesce the discharge into a volumetric and stable ultra-high-temperature plasma. As a proof of concept, we used this process to synthesize various extreme materials in seconds, including ultra-high-temperature ceramics (for example, hafnium carbonitride) and refractory metal alloys. Moreover, the carbon-fibre electrodes are highly flexible and can be shaped for various syntheses. In conclusion, this simple and practical plasma technology may help overcome the challenges in high-temperature synthesis and enable large-scale electrified plasma manufacturing powered by renewable electricity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

New High-Entropy Perovskite Oxides with Increased Reducibility and Stability for Thermochemical Hydrogen Generation

This project aims to design, synthesize, and test a transformative class of High-Entropy Perovskite Oxides (HEPOs) as redox oxides to enable thermochemical hydrogen generation with improved stability, kinetics, and efficiency. These developed HEPOs are expected to demonstrate improved kinetics with oxygen surface exchange coefficient ( k > 7.5×10 -4 cm/s) in Budget Period (BP) 1, retain its structural stability in a broad range of oxygen non-stoichiometry (Δδ > 0.15) at a low operating reduction temperature of T red < 1400°C in BP 2, and deliver a H 2 yield of over 400 µmol per gram of oxide and high stability with less than 20% degradation after at least 50 cycles in BP 3. This project is feasible due to the unique thermodynamic properties (simultaneously increased reducibility and phase stability) and kinetic characters (stability against particle coarsening and potentially enhanced oxygen transport and surface reaction kinetics) of such HEPOs, and it is enabled by a unique active learning computational design approach. Computational studies have been conducted to investigate the oxygen vacancy formation in complex perovskite systems. * Accurate prediction of V O .. concentration with disordered A-site cations in Fe-based high-entropy perovskite oxides * Combined MC/DFT computation elucidates the mechanism of Co preference on the redox due to the strain introduced by local distortion. In this project, we explored a large number (~150) of perovskite compositions, which are listed in Tables 2 – 4). * All perovskite specimens have been synthesized through a high-throughput high-energy ball milling process, followed by the conventional sintering process. * XRD, SEM/EDS and TGA were performed to confirm the crystal structure, phase homogeneity and oxygen non-stoichiometry for compositionally complex perovskite oxides (CCPOs). * 110 compositions show single-phase from XRD * Unusual aliovalent doping effects in medium-entropy perovskite compositions. * V-shape relation between Δδ vs. x (La 1-x Sr x )(Mn 1/3 Fe 1/3 Ti 1/3 )O 3 * The highest reported hydrogen production for the CCPOs made in this project ( T re = 1350 ºC 30 min, T Ox = 1100 ºC 30 min) * B-site mixing (La 0.8 Sr 0.2 )(Mn 0.2 Fe 0.2 Co 0.4 Al 0.2 )O 3 : 89.97 ± 2.73 mmol H2 /mol oxide (395 ± 10 μmol/g oxide ) (i) No phase transformation during reactions when Co molar ratio is less than 61% (ii) Balance between intrinsic kinetics (oxygen surface exchange) and thermodynamics (oxygen non-stoichiometry) (iii) Preference of Co identified by in-situ XPS * A-site mixing (La 1/6 Pr 1/6 Nd 1/6 Gd 1/6 Ba 1/6 Sr1/6)MnO 3 : 98.48 mmol H2 /mol oxid e (~415 μmol/g oxide )

08 HYDROGEN↗

Compositionally complex perovskite oxides: Discovering a new class of solid electrolytes with interface-enabled conductivity improvements

Compositionally complex ceramics (CCCs), including high-entropy ceramics, offer a vast, unexplored compositional space for materials discovery. Herein, we propose and demonstrate strategies for tailoring CCCs via a combination of non-equimolar compositional designs and control of grain boundaries (GBs) and microstructures. Using oxide solid electrolytes for all-solid-state batteries as an example, we have discovered a class of compositionally complex perovskite oxides (CCPOs) with improved lithium ionic conductivities beyond the limit of conventional doping. For example, we demonstrate that the ionic conductivity can be improved by >60% in (Li 0.375 Sr 0.4375 )(Ta 0.375 Nb 0.375 Zr 0.125 Hf 0.125 )O 3-δ compared with the (Li 0.375 Sr 0.4375 )(Ta 0.75 Zr 0.25 )O 3-δ (LSTZ) baseline. Furthermore, the ionic conductivity can be improved by another >70% via quenching, achieving >270% of the LSTZ. Notably, we demonstrate GB-enabled conductivity improvements via both promoting grain growth and altering GB structures through compositional designs and processing. In a broader perspective, this work suggests new routes for discovering and tailoring CCCs for energy storage and many other applications.

36 MATERIALS SCIENCE↗

Atomic-scale origin of the low grain-boundary resistance in perovskite solid electrolyte Li 0.375 Sr 0.4375 Ta 0.75 Zr 0.25 O 3

Oxide solid electrolytes (OSEs) have the potential to achieve improved safety and energy density for lithium-ion batteries, but their high grain-boundary (GB) resistance generally is a bottleneck. In the well-studied perovskite oxide solid electrolyte, Li 3x La 2/3-x TiO 3 (LLTO), the ionic conductivity of grain boundaries is about three orders of magnitude lower than that of the bulk. In contrast, the related Li 0.375 Sr 0.4375 Ta 0.75 Zr 0.25 O 3 (LSTZ0.75) perovskite exhibits low grain boundary resistance for reasons yet unknown. Here, we use aberration-corrected scanning transmission electron microscopy and spectroscopy, along with an active learning moment tensor potential, to reveal the atomic scale structure and composition of LSTZ0.75 grain boundaries. Vibrational electron energy loss spectroscopy is applied for the first time to reveal atomically resolved vibrations at grain boundaries of LSTZ0.75 and to characterize the otherwise unmeasurable Li distribution therein. We find that Li depletion, which is a major reason for the low grain boundary ionic conductivity of LLTO, is absent for the grain boundaries of LSTZ0.75. Instead, the low grain boundary resistivity of LSTZ0.75 is attributed to the formation of a nanoscale defective cubic perovskite interfacial structure that contained abundant vacancies. Our study provides new insights into the atomic scale mechanisms of low grain boundary resistivity.

25 ENERGY STORAGE↗

Accurate prediction of oxygen vacancy concentration with disordered A-site cations in high-entropy perovskite oxides

Abstract Entropic stabilized ABO 3 perovskite oxides promise many applications, including the two-step solar thermochemical hydrogen (STCH) production. Using binary and quaternary A-site mixed {A}FeO 3 as a model system, we reveal that as more cation types, especially above four, are mixed on the A-site, the cell lattice becomes more cubic-like but the local Fe–O octahedrons are more distorted. By comparing four different Density Functional Theory-informed statistical models with experiments, we show that the oxygen vacancy formation energies ( $${E}_{V}^{f}$$ E V f ) distribution and the vacancy interactions must be considered to predict the oxygen non-stoichiometry ( δ ) accurately. For STCH applications, the $${E}_{V}^{f}$$ E V f distribution, including both the average and the spread, can be optimized jointly to improve Δ δ (difference of δ between the two-step conditions) in some hydrogen production levels. This model can be used to predict the range of water splitting that can be thermodynamically improved by mixing cations in {A}FeO 3 perovskites.

08 HYDROGEN↗

Unusual aliovalent doping effects on oxygen non-stoichiometry in medium-entropy compositionally complex perovskite oxides

Aliovalent doping of perovskite oxides can tune the oxygen vacancy formation energy. This work discovers normal vs. abnormal aliovalent doping effects on redox behaviors in medium-entropy compositionally complex perovskite oxides (CCPOs) (La 1–x Sr x )(Mn 1/3 Fe 1/3 Ti 1/3 )O 3–δ (LS_MFT) vs. (La 1–x Sr x )(Mn 1/3 Fe 1/3 Cr 1/3 )O 3–δ (LS_MFC). In the LS_MFC series, the oxygen non-stoichiometry range Δδ (= δ red – δ ox ) linearly depends on the Sr molar ratio x, while the LS_MFT series shows a V-shape dependence of Δδ on x. This unusual observation is investigated and explained based on the analysis of the energy loss near edge structure (ELNES) in STEM electron energy loss spectroscopy, along with density functional theory (DFT) calculations. In LS_MFC, Cr–L 2,3 , Mn–L 2,3 and Fe–L 2,3 peaks have a similar linear shift to higher energy with increasing x, which indicates higher oxidation states of Cr, Mn, and Fe with lower oxygen vacancy formation energies. In LS_MFT, the V-shape of the Δδ vs. x curve is caused by the stable Ti 4+ state and a V-shape Mn/Fe valency dependence on x. Furthermore, this study suggests the possible existence of different (including unexpected) coupled aliovalent doping effects in CCPOs with multiple B-site redox active elements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗