Engineering topics

Luong, Duy Xuan

Publications and source records attributed to Luong, Duy Xuan.

14 records

DOE OSTI2024

Nondestructive flash cathode recycling

Effective recycling of end-of-life Li-ion batteries (LIBs) is essential due to continuous accumulation of battery waste and gradual depletion of battery metal resources. The present closed-loop solutions include destructive conversion to metal compounds, by destroying the entire three-dimensional morphology of the cathode through continuous thermal treatment or harsh wet extraction methods, and direct regeneration by lithium replenishment. Here, we report a solvent- and water-free flash Joule heating (FJH) method combined with magnetic separation to restore fresh cathodes from waste cathodes, followed by solid-state relithiation. The entire process is called flash recycling. This FJH method exhibits the merits of milliseconds of duration and high battery metal recovery yields of ~98%. After FJH, the cathodes reveal intact core structures with hierarchical features, implying the feasibility of their reconstituting into new cathodes. Relithiated cathodes are further used in LIBs, and show good electrochemical performance, comparable to new commercial counterparts. Life-cycle-analysis highlights that flash recycling has higher environmental and economic benefits over traditional destructive recycling processes.

25 ENERGY STORAGE↗

DOE OSTI2023

Automated Laboratory Kilogram-Scale Graphene Production from Coal

The flash Joule heating (FJH) method converts many carbon feedstocks into graphene in milliseconds to seconds using an electrical pulse. This opens an opportunity for processing low or negative value resources, such as coal and plastic waste, into high value graphene. Here, in this work, a lab-scale automation FJH system that allows the synthesis of 1.1 kg of turbostratic flash graphene from coal-based metallurgical coke (MC) in 1.5 h is demonstrated. The process is based on the automated conversion of 5.7 g of MC per batch using an electrical pulse width modulation system to conduct the bottom-up upcycle of MC into flash graphene. This study then compare this method to two other scalable graphene synthesis techniques by both a life cycle assessment and a technoeconomic assessment.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Waste plastic- and coke-derived flash graphene as lubricant additives

Lubricants play an essential role in reducing wear in mechanical systems. Carbon nanomaterial additives, such as graphene, have been found to significantly improve tribological performance when used as lubricant additives. Here, in this study, post-consumer plastic and metallurgical coke are converted into turbostratic flash graphene (FG) through flash Joule heating (FJH). The FG is then added to either poly(alpha olefin) 6 or 9 (PAO 6 or PAO 9). Adding waste plastic-derived FG (WPFG) and metallurgical coke-derived FG (MCFG) to lubricants resulted in a significant decrease in the coefficient of friction (CoF), wear scar diameter (WSD), and roughness during four-ball testing. WPFG and MCFG decrease the CoF in PAO 9 by 6% and 9% at 0.1 mg mL -1 , respectively, and in PAO 6 by 23% and 6% at 0.5 mg mL -1 , respectively. WPFG and MCFG decrease the WSD of steel balls in PAO 9 by 14% and 8% at 0.5 mg mL -1 , respectively, and in PAO 6 by 12% and 14% at 0.5 mg mL -1 , respectively, by forming a coating-like layer between the metal surfaces. Roughness decreased by 38% and 32% for WPFG and MCFG in PAO 6, respectively, and by 35% and 29% for WPFG and MCFG in PAO 9, respectively. Finally, preliminary life cycle analyses demonstrate that production of FG produces up to 99% less greenhouse gas emissions, requires 98% less energy, and consumes 99.9% less water when compared to conventional production techniques of graphene. Hence, metallurgical coke and waste plastic are shown to be ready feedstocks for high-quality FG lubricant additives.

36 MATERIALS SCIENCE↗

DOE OSTI2022

High-surface-area corundum nanoparticles by resistive hotspot-induced phase transformation

Abstract High-surface-area α-Al 2 O 3 nanoparticles are used in high-strength ceramics and stable catalyst supports. The production of α-Al 2 O 3 by phase transformation from γ-Al 2 O 3 is hampered by a high activation energy barrier, which usually requires extended high-temperature annealing (~1500 K, > 10 h) and suffers from aggregation. Here, we report the synthesis of dehydrated α-Al 2 O 3 nanoparticles (phase purity ~100%, particle size ~23 nm, surface area ~65 m 2 g −1 ) by a pulsed direct current Joule heating of γ-Al 2 O 3 . The phase transformation is completed at a reduced bulk temperature and duration (~573 K, < 1 s) via an intermediate δʹ-Al 2 O 3 phase. Numerical simulations reveal the resistive hotspot-induced local heating in the pulsed current process enables the rapid transformation. Theoretical calculations show the topotactic transition (from γ- to δʹ- to α-Al 2 O 3 ) is driven by their surface energy differences. The α-Al 2 O 3 nanoparticles are sintered to nanograined ceramics with hardness superior to commercial alumina and approaching that of sapphire.

Deng, Bing (ORCID:0000000305308410)↗

DOE OSTI2022

Heteroatom-Doped Flash Graphene

Heteroatom doping can effectively tailor the local structures and electronic states of intrinsic two-dimensional materials, and endow them with modified optical, electrical, and mechanical properties. Recent studies have shown the feasibility of preparing doped graphene from graphene oxide and its derivatives via some post-treatments, including solid-state and solvothermal methods, but they require reactive and harsh reagents. However, direct synthesis of various heteroatom-doped graphene in larger quantities and high purity through bottom-up methods remains challenging. Here, we report catalyst-free and solvent-free direct synthesis of graphene doped with various heteroatoms in bulk via flash Joule heating (FJH). Seven types of heteroatom-doped flash graphene (FG) are synthesized through millisecond flashing, including single-element-doped FG (boron, nitrogen, oxygen, phosphorus, sulfur), two-element-co-doped FG (boron and nitrogen), as well as three-element-co-doped FG (boron, nitrogen, and sulfur). Here, a variety of low-cost dopants, such as elements, oxides, and organic compounds are used. The graphene quality of heteroatom-doped FG is high, and similar to intrinsic FG, the material exhibits turbostraticity, increased interlayer spacing, and superior dispersibility. Electrochemical oxygen reduction reaction of different heteroatom-doped FG is tested, and sulfur-doped FG shows the best performance. Lithium metal battery tests demonstrate that nitrogen-doped FG exhibits a smaller nucleation overpotential compared to Cu or undoped FG. The electrical energy cost for the synthesis of heteroatom-doped FG synthesis is only 1.2 to 10.7 kJ g –1 , which could render the FJH method suitable for low-cost mass production of heteroatom-doped graphene.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Rare earth elements from waste

Rare earth elements (REEs) are critical materials in electronics and clean technologies. With the diminishing of easily accessible minerals for mining, the REE recovery from waste is an alternative toward a circular economy. Present methods for REE recovery suffer from lengthy purifications, low extractability, and high wastewater streams. Here, we report an ultrafast electrothermal process (~3000°C, ~1 s) based on flash Joule heating (FJH) for activating wastes to improve REE extractability. FJH thermally degrades or reduces the hard-to-dissolve REE species to components with high thermodynamic solubility, leading to ~2× increase in leachability and high recovery yields using diluted acid (e.g., 0.1 M HCl). The activation strategy is feasible for various wastes including coal fly ash, bauxite residue, and electronic waste. The rapid FJH process is energy-efficient with a low electrical energy consumption of 600 kWh ton –1 . The potential for this route to be rapidly scaled is outlined.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Phase controlled synthesis of transition metal carbide nanocrystals by ultrafast flash Joule heating

Nanoscale carbides enhance ultra-strong ceramics and show activity as high-performance catalysts. Traditional lengthy carburization methods for carbide syntheses usually result in coked surface, large particle size, and uncontrolled phase. Here, a flash Joule heating process is developed for ultrafast synthesis of carbide nanocrystals within 1 s. Various interstitial transition metal carbides (TiC, ZrC, HfC, VC, NbC, TaC, Cr 2 C 3 , MoC, and W 2 C) and covalent carbides (B 4 C and SiC) are produced using low-cost precursors. By controlling pulse voltages, phase-pure molybdenum carbides including β-Mo 2 C and metastable α-MoC 1-x and η-MoC 1-x are selectively synthesized, demonstrating the excellent phase engineering ability of the flash Joule heating by broadly tunable energy input that can exceed 3000 K coupled with kinetically controlled ultrafast cooling (>10 4 K s –1 ). Theoretical calculation reveals carbon vacancies as the driving factor for topotactic transition of carbide phases. The phase-dependent hydrogen evolution capability of molybdenum carbides is investigated with β-Mo 2 C showing the best performance.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Converting plastic waste pyrolysis ash into flash graphene

Pyrolysis of plastic waste (PW), a commercial method of recycling, is currently economically challenging and produces up to 20% by mass valueless pyrolysis ash (PA) as a byproduct. Here, direct, facile upcycling of PW-derived PA into high purity turbostratic flash graphene (tFG) is demonstrated. The tFG displays excellent dispersibility, yielding a concentration of 2.84 mg/mL in aqueous surfactant solution. The tFG was used to fabricate tFG-PVA nanocomposites, and low doses of tFG (0.1%–1%) improve failure strain by 15%–30% when compared to the samples of neat PVA. Furthermore, the addition of tFG to PVA films showed decreased hydrophilic interactions, increasing the water contact angle by 235% and adsorbing 500% less water than neat PVA. The tFG was also added to Portland cement paste as well as concrete, and exhibited 43% and 25% increases in compressive strength, respectively. The tFG is used directly in both composite applications, requiring no purification or chemical functionalization, unlike many other products used in nanocomposites.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Large–Scale Syntheses of 2D Materials: Flash Joule Heating and Other Methods

In the past 17 years, the larger-scale production of graphene and graphene family materials has proven difficult and costly, thus slowing wider-scale commercial applications. Here, the quality of the graphene that is prepared on larger scales has often been poor, demonstrating a need for improved quality controls. Here, current industrial graphene synthetic and analytical methods, as well as recent academic advancements in larger-scale or sustainable synthesis of graphene, defined here as weights more than 200 mg or films larger than 200 cm 2 , are compiled and reviewed. There is a specific emphasis on recent research in the use of flash Joule heating as a rapid, efficient, and scalable method to produce graphene and other 2D nanomaterials. Reactor design, synthetic strategies, safety considerations, feedstock selection, Raman spectroscopy, and future outlooks for flash Joule heating syntheses are presented. To conclude, the remaining challenges and opportunities in the larger-scale synthesis of graphene and a perspective on the broader use of flash Joule heating for larger-scale 2D materials synthesis are discussed.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Urban mining by flash Joule heating

Abstract Precious metal recovery from electronic waste, termed urban mining, is important for a circular economy. Present methods for urban mining, mainly smelting and leaching, suffer from lengthy purification processes and negative environmental impacts. Here, a solvent-free and sustainable process by flash Joule heating is disclosed to recover precious metals and remove hazardous heavy metals in electronic waste within one second. The sample temperature ramps to ~3400 K in milliseconds by the ultrafast electrical thermal process. Such a high temperature enables the evaporative separation of precious metals from the supporting matrices, with the recovery yields >80% for Rh, Pd, Ag, and >60% for Au. The heavy metals in electronic waste, some of which are highly toxic including Cr, As, Cd, Hg, and Pb, are also removed, leaving a final waste with minimal metal content, acceptable even for agriculture soil levels. Urban mining by flash Joule heating would be 80× to 500× less energy consumptive than using traditional smelting furnaces for metal-component recovery and more environmentally friendly.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Ultrafast and Controllable Phase Evolution by Flash Joule Heating

Flash Joule heating (FJH), an advanced material synthesis technique, has been used for the production of high-quality carbon materials. Direct current discharge through the precursors by large capacitors has successfully converted carbon-based starting materials into bulk quantities of turbostratic graphene by the FJH process. However, the formation of other carbon allotropes, such as nanodiamonds and concentric carbon materials, as well as the covalent functionalization of different carbon allotropes by the FJH process, remains challenging. Here, we report the solvent-free FJH synthesis of three different fluorinated carbon allotropes: fluorinated nanodiamonds, fluorinated turbostratic graphene and fluorinated concentric carbon. This is done by millisecond flashing of organic fluorine compounds and fluoride precursors. Spectroscopic analysis confirms the modification of the electronic states and the existence of various short-range and long-range orders in the different fluorinated carbon allotropes. As a result, the flash time-dependent relationship is further demonstrated to control the phase evolution and product compositions.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Flash graphene from rubber waste

Most conventional production processes for graphene are time-consuming, solvent-intensive, and energetically demanding. To circumvent these limitations for mass production, flash Joule heating (FJH) has been shown to be an effective method to synthesize graphene. Here, methods for optimizing production of graphene from rubber waste feedstocks are shown. Through careful control of system parameters, such as pulse voltage and pulse time, turbostratic flash graphene (tFG) can be produced from rubber waste. It is characterized by Raman spectroscopy, X-ray diffraction and thermogravimetric analysis. Here, the resulting tFG can be easily exfoliated and dispersed into various solvents because of its turbostratic arrangement. Addition of tFG into Portland cement results in a significant increase in the compressive strength of the composite. From a materials perspective, FJH offers a facile and inexpensive method for producing high quality tFG from rubber waste materials, which would otherwise be disposed of in landfills or burned for fuel. FJH allows for upcycling of low-value rubber waste into high-value carbon nanomaterials for use as reinforcing additives.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Millisecond Conversion of Metastable 2D Materials by Flash Joule Heating

Controllable phase engineering is vital for precisely tailoring material properties since different phase structures have various electronic states and atomic arrangements. Rapid synthesis of thermodynamically metastable materials, especially two-dimensional metastable materials, with high efficiency and low cost remains a large challenge. Here we report flash Joule heating (FJH) as an electrothermal method to achieve the bulk conversion of transition metal dichalcogenides, MoS 2 and WS 2 , from 2H phases to 1T phases in milliseconds. The conversions can reach up to 76% of flash MoS 2 using tungsten powder as conductive additive. Different degrees of phase conversion can be realized by controlling the FJH conditions, such as reaction duration and additives, which allows the study of ratio-dependent properties. First-principles calculations confirm that structural processes associated with the FJH, such as vacancy formation and charge accumulation, result in stabilization of the 1T phases. Furthermore, FJH offers rapid access to bulk quantities of the hitherto hard-to-access 1T phases, a promising method for further fundamental research and diverse applications of metastable phases.

2D materials↗

DOE OSTI2020

Flash Graphene from Plastic Waste

In this work, an approach to upcycling plastic waste (PW) products is presented. The method relies on flash Joule heating (FJH) to convert PW into flash graphene (FG). In addition to FG, the process results in the formation of carbon oligomers, hydrogen, and light hydrocarbons. In order to make high quality graphene, a sequential alternating current (AC) and direct current (DC) flash is used. Here, the FJH process requires no catalyst and works for PW mixtures, which makes the process suitable for handling landfill PW. The energy required to convert PW to FG is ~ 23 kJ/g or ~ $125 in electricity per ton of PW, potentially making this process economically attractive for scale-up. The FG was characterized by Raman spectroscopy and had a I 2D /I G peak ratio up to 6 with a low-intensity D band. Moreover, transmission electron microscopy and X-ray diffraction analysis show that the FG is turbostratic with an interlayer spacing of 3.45 Å. The large interlayer spacing will facilitate its dispersion in liquids and composites. Analysis of FG dispersions in 1% Pluronic aqueous solution shows that concentrations up to 1.2 mg/mL can be achieved. The carbon oligomers that distilled from the process were characterized by Fourier-transform infrared spectroscopy and have chemical structures similar to the starting PW. Initial analysis of gas phase products shows the formation of considerable amounts of hydrogen along with other light hydrocarbons. Since graphene is naturally occurring and it shows a low toxicity profile, this could be an environmentally beneficial method to upcycle PE.

54 ENVIRONMENTAL SCIENCES↗