Search NASA⌕ Search

Engineering topics

Lux, James

Publications and source records attributed to Lux, James.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

The Sun Radio Interferometer Space Experiment (SunRISE) Mission

The Sun Radio Interferometer Space Experiment (SunRISE) will provide an entirely new view on particle acceleration and transport in the inner heliosphere by creating the first low radio frequency interferometer in space to localize heliospheric radio emissions. By imaging and determining the location of decametric-hectometric (DH, 0.1 MHz–23 MHz) solar radio bursts, SunRISE will provide key information on particle acceleration mechanisms associated with coronal mass ejections (CMEs) and the magnetic field topology from active regions into interplanetary space. The SunRISE Observatory will consist of six space vehicles in a passive formation, in orbits designed to keep them within approximately 10 km of each other, and flying in a supersynchronous geosynchronous Earth orbit (GEO). Each space vehicle consists of a Solar DH-GNSS payload and a 6U form factor spacecraft. The SunRISE Observatory together with significant ground-based processing, will enable imaging of the Sun in a portion of the spectrum that is blocked by the ionosphere and cannot be observed from Earth. Key aspects that enable this mission are that only position knowledge of the space vehicles is required, not active control, and that the architecture involves a modest amount of on-board processing coupled with significant ground-based processing for navigation, position determination, and science operations. Mission-enabling advances in software-defined radios, GPS navigation and timing, and small spacecraft technologies, developed and flown on the DARPA High Frequency Research (DHFR) and the Community Initiative for Continuing Earth Radio Occultation (CICERO) have made this mission affordable and low-risk. The SunRISE mission will exploit the multiple spacecraft per aperture (MSPA) capability of NASA’s Deep Space Network (DSN), for more efficient data transfers of larger data volumes, and utilize commercial access to space, in which the SunRISE space vehicles will be carried to their target orbit as secondary payloads in conjunction with a larger host spacecraft intended for GEO.

Neilson, Tim↗
NASA NTRS2021

The Sun Radio Interferometer Space Experiment (SunRISE) Mission

The Sun Radio Interferometer Space Experiment (SunRISE) will provide an entirely new view on particle acceleration and transport in the inner heliosphere by creating the first low radio frequency interferometer in space to localize heliospheric radio emissions. By imaging and determining the location of decametric-hectometric (DH) radio bursts from 0.1 MHz–25 MHz, SunRISE will provide key information on particle acceleration mechanisms associated with coronal mass ejections (CMEs) and the magnetic field topology from active regions into interplanetary space. Six small spacecraft, of a 6U form factor, will fly in a supersynchronous geosynchronous Earth orbit (GEO) orbit within about 10 km of each other, in a passive formation, and image the Sun in a portion of the spectrum that is blocked by the ionosphere and cannot be observed from Earth. Key aspects that enable this mission are that only position knowledge of the spacecraft is required, not active control, and that the architecture involves a modest amount of on-board processing coupled with significant ground-based processing for navigation, position determination, and science operations. Mission-enabling advances in software-defined radios, GPS navigation and timing, and small spacecraft technologies, developed and flown on the DARPA High Frequency Research (DHFR), the Community Initiative for Continuing Earth Radio Occultation (CICERO), and the Mars Cube One (MarCO) missions, have made this mission affordable and low-risk. The SunRISE mission will involve utilizing commercial access to space, in which the SunRISE spacecraft will be carried to their target orbit as a secondary payload in conjunction with a larger host spacecraft intended for GEO.

Neilson, Tim↗
NASA NTRS2013

Target & Propagation Models for the FINDER Radar

Finding persons still alive in piles of rubble following an earthquake, a severe storm, or other disaster is a difficult problem. JPL is currently developing a victim detection radar called FINDER (Finding Individuals in Emergency and Response). The subject of this paper is directed toward development of propagation & target models needed for simulation & testing of such a system. These models are both physical (real rubble piles) and numerical. Early results from the numerical modeling phase show spatial and temporal spreading characteristics when signals are passed through a randomly mixed rubble pile.

propagation↗
NASA NTRS2009

System for Automated Calibration of Vector Modulators

Vector modulators are used to impose baseband modulation on RF signals, but non-ideal behavior limits the overall performance. The non-ideal behavior of the vector modulator is compensated using data collected with the use of an automated test system driven by a LabVIEW program that systematically applies thousands of control-signal values to the device under test and collects RF measurement data. The technology innovation automates several steps in the process. First, an automated test system, using computer controlled digital-to-analog converters (DACs) and a computer-controlled vector network analyzer (VNA) systematically can apply different I and Q signals (which represent the complex number by which the RF signal is multiplied) to the vector modulator under test (VMUT), while measuring the RF performance specifically, gain and phase. The automated test system uses the LabVIEW software to control the test equipment, collect the data, and write it to a file. The input to the Lab - VIEW program is either user-input for systematic variation, or is provided in a file containing specific test values that should be fed to the VMUT. The output file contains both the control signals and the measured data. The second step is to post-process the file to determine the correction functions as needed. The result of the entire process is a tabular representation, which allows translation of a desired I/Q value to the required analog control signals to produce a particular RF behavior. In some applications, corrected performance is needed only for a limited range. If the vector modulator is being used as a phase shifter, there is only a need to correct I and Q values that represent points on a circle, not the entire plane. This innovation has been used to calibrate 2-GHz MMIC (monolithic microwave integrated circuit) vector modulators in the High EIRP Cluster Array project (EIRP is high effective isotropic radiated power). These calibrations were then used to create correction tables to allow the commanding of the phase shift in each of four channels used as a phased array for beam steering of a Ka-band (32-GHz) signal. The system also was the basis of a breadboard electronic beam steering system. In this breadboard, the goal was not to make systematic measurements of the properties of a vector modulator, but to drive the breadboard with a series of test patterns varying in phase and amplitude. This is essentially the same calibration process, but with the difference that the data collection process is oriented toward collecting breadboard performance, rather than the measurement of output from a network analyzer.

Lux, James↗
NASA NTRS2009

Generating Ka-Band Signals Using an X-Band Vector Modulator

A breadboard version of a transmitter for radio communication at a carrier frequency of 32 GHz (which is in the Ka band) utilizes a vector modulator operating at a carrier frequency of 8 GHz (the low end of the X band) to generate any of a number of advanced modulations that could include amplitude and/or phase modulation components. The 8-GHz modulated signal is mixed with a 24-GHz signal generated by an upconverter to obtain the desired 32-GHz modulated output. The transmitter is being developed as a prototype of downlink transmitters for transmission of data from spacecraft to Earth at high rates (>100 Mb/s). The transmitter design could also be adapted to terrestrial and Earth/satellite communication links. The advanced modulations (which can include M-ary phase-shift keying (M-PSK), offset phase-shift keying (OPSK), and M-ary quadrature amplitude modulation (M-QAM). These modulations are needed because for a given amount of signal bandwidth, they enable transmission of data at rates greater than those of older, simpler modulation schemes. The transmitter architecture (see figure) was chosen not only to enable generation of the required modulations at 32 GHz but also to reduce the number of components needed to implement the transmitter. Instead of incorporating an 8-GHz signal source, the transmitter utilizes an 8-GHz signal generated by a voltage-controlled oscillator that is part of an X-band transponder with which the fully developed version of this transmitter would be used in the original intended spacecraft application. The oscillator power is divided onto two paths, one of which goes through the vector modulator, the other through amplifiers and a 3 frequency multiplier. Band-pass filters are included downstream of the frequency multiplier to suppress unwanted harmonics.

Smith, Scott↗
NASA NTRS2007

VCO PLL Frequency Synthesizers for Spacecraft Transponders

Two documents discuss a breadboard version of advanced transponders that, when fully developed, would be installed on future spacecraft to fly in deep space. These transponders will be required to be capable of operation on any deepspace- communications uplink frequency channel between 7,145 and 7,235 MHz, and any downlink frequency channel between 8,400 and 8,500 MHz. The document focuses on the design and operation of frequency synthesizers for the receiver and transmitter. Heretofore, frequency synthesizers in deep-space transponders have been based on dielectric resonator oscillators (DROs), which do not have the wide tuning bandwidth necessary to tune over all channels in the uplink or downlink frequency bands. To satisfy the requirement for tuning bandwidth, the present frequency synthesizers are based on voltage-controlled-oscillator (VCO) phase-locked loops (PLLs) implemented by use of monolithic microwave integrated circuits (MMICs) implemented using inGaP heterojunction bipolar transistor (HBT) technology. MMIC VCO PLL frequency synthesizers similar to the present ones have been used in commercial and military applications but, until now, have exhibited too much phase noise for use in deep-space transponders. The present frequency synthesizers contain advanced MMIC VCOs, which use HBT technology and have lower levels of flicker (1/f) phase noise. When these MMIC VCOs are used with high-speed MMIC frequency dividers, it becomes possible to obtain the required combination of frequency agility and low phase noise.

Smith, Scott↗
NASA NTRS2007

Wide Tuning Capability for Spacecraft Transponders

A document presents additional information on the means of implementing a capability for wide tuning of microwave receiver and transmitter frequencies in the development reported in the immediately preceding article, VCO PLL Frequency Synthesizers for Spacecraft Transponders (NPO- 42909). The reference frequency for a PLL-based frequency synthesizer is derived from a numerically controlled oscillator (NCO) implemented in digital logic, such that almost any reference frequency can be derived from a fixed crystal reference oscillator with microhertz precision. The frequency of the NCO is adjusted to track the received signal, then used to create another NCO frequency used to synthesize the transmitted signal coherent with, and at a specified frequency ratio to, the received signal. The frequencies can be changed, even during operation, through suitable digital programming. The NCOs and the related tracking loops and coherent turnaround logic are implemented in a field-programmable gate array (FPGA). The interface between the analog microwave receiver and transmitter circuits and the FPGA includes analog-to-digital and digital-toanalog converters, the sampling rates of which are chosen to minimize spurious signals and otherwise optimize performance. Several mixers and filters are used to properly route various signals.

Lux, James↗
NASA NTRS2007

Inexpensive Clock for Displaying Planetary or Sidereal Time

An inexpensive wall clock has been devised for displaying solar time or sidereal time as it would be perceived on a planet other than the Earth, or for displaying sidereal time on the Earth. The concept of a wall clock synchronized to a period other than the terrestrial mean solar day is not new in itself. What is new here is that the clock is realized through a relatively simple electronic modification of a common battery-powered, quartz-crystal-oscillator-driven wall clock. The essence of the modification is to shut off the internal oscillator of the clock and replace the internal-oscillator output signal with a signal of the required frequency generated by an external oscillator. The unmodified clock electronic circuitry includes a quartz crystal connected to an integrated circuit (IC) that includes, among other parts, a buffer amplifier that conditions the oscillator output. The modification is effected by removing the quartz crystal and connecting the output terminal of the external oscillator, via a capacitor, to the input terminal of the buffer amplifier

Lux, James↗
NASA NTRS2007

Efficient Switching Arrangement for (N + 1)/N Redundancy

An efficient arrangement of four switches has been conceived for coupling, to four output ports, the output powers of any subset of four devices that are members of a redundant set of five devices. In normal operation, the output power of each of four of the devices would be coupled to one of the four output ports. The remaining device would be kept as a spare: normally, its output power would be coupled to a load, wherein that power would be dissipated. In the event of failure of one of the four normally used devices, that device would be disconnected from its output port and connected to the load, and the spare device would be connected to the output from which the failed device was disconnected. Alternatively or in addition, the outputs of one or more devices could be sent to ports other than the ones originally assigned to them.

Lux, James↗
NASA NTRS2006

Detecting Negative Obstacles by Use of Radar

Robotic land vehicles would be equipped with small radar systems to detect negative obstacles, according to a proposal. The term "negative obstacles" denotes holes, ditches, and any other terrain features characterized by abrupt steep downslopes that could be hazardous for vehicles. Video cameras and other optically based obstacle-avoidance sensors now installed on some robotic vehicles cannot detect obstacles under adverse lighting conditions. Even under favorable lighting conditions, they cannot detect negative obstacles. A radar system according to the proposal would be of the frequency-modulation/ continuous-wave (FM/CW) type. It would be installed on a vehicle, facing forward, possibly with a downward slant of the main lobe(s) of the radar beam(s) (see figure). It would utilize one or more wavelength(s) of the order of centimeters. Because such wavelengths are comparable to the characteristic dimensions of terrain features associated with negative hazards, a significant amount of diffraction would occur at such features. In effect, the diffraction would afford a limited ability to see corners and to see around corners. Hence, the system might utilize diffraction to detect corners associated with negative obstacles. At the time of reporting the information for this article, preliminary analyses of diffraction at simple negative obstacles had been performed, but an explicit description of how the system would utilize diffraction was not available.

Mittskus, Anthony↗
NASA NTRS2006

Multichannel Phase and Power Detector

An electronic signal-processing system determines the phases of input signals arriving in multiple channels, relative to the phase of a reference signal with which the input signals are known to be coherent in both phase and frequency. The system also gives an estimate of the power levels of the input signals. A prototype of the system has four input channels that handle signals at a frequency of 9.5 MHz, but the basic principles of design and operation are extensible to other signal frequencies and greater numbers of channels. The prototype system consists mostly of three parts: An analog-to-digital-converter (ADC) board, which coherently digitizes the input signals in synchronism with the reference signal and performs some simple processing; A digital signal processor (DSP) in the form of a field-programmable gate array (FPGA) board, which performs most of the phase- and power-measurement computations on the digital samples generated by the ADC board; and A carrier board, which allows a personal computer to retrieve the phase and power data. The DSP contains four independent phase-only tracking loops, each of which tracks the phase of one of the preprocessed input signals relative to that of the reference signal (see figure). The phase values computed by these loops are averaged over intervals, the length of which is chosen to obtain output from the DSP at a desired rate. In addition, a simple sum of squares is computed for each channel as an estimate of the power of the signal in that channel. The relative phases and the power level estimates computed by the DSP could be used for diverse purposes in different settings. For example, if the input signals come from different elements of a phased-array antenna, the phases could be used as indications of the direction of arrival of a received signal and/or as feedback for electronic or mechanical beam steering. The power levels could be used as feedback for automatic gain control in preprocessing of incoming signals. For another example, the system could be used to measure the phases and power levels of outputs of multiple power amplifiers to enable adjustment of the amplifiers for optimal power combining.

Li, Samuel↗
NASA NTRS2005

LabVIEW Interface for PCI-SpaceWire Interface Card

This software provides a LabView interface to the NT drivers for the PCISpaceWire card, which is a peripheral component interface (PCI) bus interface that conforms to the IEEE-1355/ SpaceWire standard. As SpaceWire grows in popularity, the ability to use SpaceWire links within LabVIEW will be important to electronic ground support equipment vendors. In addition, there is a need for a high-level LabVIEW interface to the low-level device- driver software supplied with the card. The LabVIEW virtual instrument (VI) provides graphical interfaces to support all (1) SpaceWire link functions, including message handling and routing; (2) monitoring as a passive tap using specialized hardware; and (3) low-level access to satellite mission-control subsystem functions. The software is supplied in a zip file that contains LabVIEW VI files, which provide various functions of the PCI-SpaceWire card, as well as higher-link-level functions. The VIs are suitably named according to the matching function names in the driver manual. A number of test programs also are provided to exercise various functions.

Lux, James↗
NASA NTRS2005

Alternative Way of Shifting Mass to Move a Spherical Robot

The method proposed calls for suspending a payload by use of four or more cables that would be anchored to the inner surface of the sphere. In this method, the anchor points would not be diametrically opposite points defining Cartesian axes. The payload, which includes the functional analog of the aforementioned control box, would contain winches that would shorten or lengthen the cables in a coordinated manner to shift the position of the payload within the shell.

Lux, James↗
NASA NTRS2005

Displacing Unpredictable Nulls in Antenna Radiation Patterns

A method of maintaining radio communication despite the emergence of unpredictable fades and nulls in the radiation pattern of an antenna has been proposed. The method was originally intended to be applied in the design and operation of a radio antenna aboard a robotic exploratory vehicle on a remote planet during communication with a spacecraft in orbit around the planet. The method could also be applied in similar terrestrial situations for example, radio communication between two ground vehicles or between a ground vehicle and an aircraft or spacecraft. The method is conceptually simple, is readily adaptable to diverse situations, and can be implemented without adding greatly to the weight, cost, power demand, or complexity of a system to which it may be applied. The unpredictable fades and nulls in an antenna radiation pattern arise because of electromagnetic interactions between the antenna and other objects within the near field of the antenna (basically, objects within a distance of a few wavelengths). These objects can include general vehicle components, masts, robotic arms, other antennas, the ground, and nearby terrain features. Figure 1 presents representative plots of signal strength versus time during a typical pass of a spacecraft or aircraft through the far field of such an antenna, showing typical nulls and fades caused by nearby objects. The traditional approach to ensuring reliability of communication in the presence of deep fades calls for increasing the effective transmitter power and/or reducing the receiver noise figure at the affected ground vehicle, possibly in combination with appropriate redesign of the equipment at the spacecraft or aircraft end of the communication link. These solutions can be expensive and/or risky and, depending on the application, can add significantly to weight, cost, and power demand. The proposed method entails none of these disadvantages.

Lux, James↗