Engineering topics

Lynde, Michelle N.

Publications and source records attributed to Lynde, Michelle N..

9 records

NASA NTRS2019

Additional Findings from the Common Research Model Natural Laminar Flow Wind Tunnel Test

An experimental investigation of the Common Research Model with Natural Laminar Flow (CRM-NLF) took place in the National Transonic Facility (NTF) at the NASA Langley Research Center in 2018. The 5.2% scale semispan model was designed using a new natural laminar flow design method, Crossflow Attenuated NLF (CATNLF). CATNLF enables laminar flow on typical transport wings with high sweep and Reynolds number by reshaping the wing airfoils to obtain specific pressure distribution characteristics that control the crossflow growth near the leading edge. The CATNLF method also addresses Tollmien- Schlichting transition, attachment line transition, and Görtler vortices. During the wind tunnel test, data were acquired to address three primary test objectives: validate the CATNLF design method, characterize the NTF laminar flow testing capabilities, and establish best practices for laminar flow wind tunnel testing. The present paper provides both experimental and computational data to understand the CRM-NLF laminar flow characteristics, as well as address the three primary test objectives. The effects of angle of attack and Reynolds number on the CRM-NLF laminar flow extent are studied, and the dominant transition mechanism is evaluated at a variety of test conditions. Critical N-factors are calculated for the NTF environment, and a discussion on best practices for laminar flow wind tunnel testing is provided. The CRM-NLF in the NTF provided initial confirmation of the ability of the CATNLF method to suppress crossflow growth and enable significant extents of laminar flow on transport wings with high sweep and Reynolds numbers.

Lynde, Michelle N.↗

NASA NTRS2019

A Knowledge-Based Optimization Method for Aerodynamic Design

A new aerodynamic design method, CODISC, has been developed that combines a legacy knowledge-based design method, CDISC, with a simple optimization module known as SOUP. The primary goal of this new design system is to improve the performance gains obtained using CDISC without adding significant computational time. An additional objective of this approach is to reduce the need for a priori knowledge of good initial input variable values, as well as for subsequent manual revisions of those values as the design progresses. Several test cases illustrate the development of the process to date and some of the options available at transonic and supersonic speeds for turbulent flow designs. The test cases generally start from good baseline configurations and, in all cases, were able to improve the performance. Several new guidelines for good initial values for the design variables, as well as new design rules within CDISC itself, were developed from these cases.

SOUP↗

NASA NTRS2019

Preliminary Results from an Experimental Assessment of a Natural Laminar Flow Design Method

A 5.2% scale semispan model of the new Common Research Model with Natural Laminar Flow (CRM-NLF) was tested in the National Transonic Facility (NTF) at the NASA Langley Research Center. The model was tested at transonic cruise flight conditions with Reynolds numbers based on mean aerodynamic chord ranging from 10 to 30 million. The goal of the test was to experimentally validate a new design method, referred to as Crossflow Attenuated NLF (CATNLF), which shapes airfoils to have pressure distributions that delay transition on wings with high sweep and Reynolds numbers. Additionally, the test aimed to characterize the NTF laminar flow testing capabilities, as well as establish best practices for laminar flow wind tunnel testing. Preliminary results regarding the first goal of validating the new design method are presented in this paper. Experimental data analyzed in this assessment include surface pressure data and transition images. The surface pressure data acquired during the test agree well with computational fluid dynamics (CFD) results. Transition images at a variety of Reynolds numbers and angles of attack are presented and compared to computational transition predictions. The experimental data are used to assess transition due to a turbulent attachment line, as well as crossflow and Tollmien-Schlichting modal instabilities. Preliminary results suggest the CATNLF design method is successful at delaying transition on wings with high sweep. Initial analysis of the transition front images showed transition Reynolds numbers that exceed historic experimental values at similar sweep angles. , section lift

Lynde, Michelle N.↗

NASA NTRS2018

Application of a Knowledge-Based Optimization Method for Aerodynamic Design

The current research is investigating the application of an optimization technique to an existing knowledge-based design tool. The optimization method, referred to as CODISC, helps improve the results from a knowledge-based design by eliminating the required advanced design knowledge, or help fine-tune a well-performing vehicle. Three CODISC designs are presented using a generic transonic transport, the Common Research Model (CRM). One design optimizes the baseline CRM to demonstrate the ability to improve a well-performing vehicle. Another design is performed from the CRM with camber and twist removed, which highlights the ability to use CODISC in the conceptual design phase. The final design implements laminar flow on the CRM, showing how CODISC can optimize the extent of laminar flow to find the best aerodynamic performance. All three CODISC designs reduced the vehicle drag compared to the baseline CRM, and highlight the new optimization technique’s versatility in the aircraft design industry.

CODISC↗

NASA NTRS2018

Development of a Knowledge-Based Optimization Method for Aerodynamic Design

A new aerodynamic design method, CODISC, has been developed that combines an existing knowledgebased design method, CDISC, with a simple optimization module known as SOUP. The primary goal of this new design system is to improve the performance gains obtained using CDISC without adding significant computational time. An additional benefit of this approach is a reduction in the need for a priori knowledge of good initial input variable values as well as for subsequent manual revisions of those values as the design progresses. A series of 2D and 3D test cases are used to illustrate the development of the process and some of the options available at transonic and supersonic speeds for both laminar and turbulent flow. The test cases start from good baseline configurations and, in all cases, were able to improve the performance. Several new guidelines for good initial values for the design variables, as well new design rules within CDISC itself, were developed from these cases.

Campbell, Richard L.↗

NASA NTRS2017

Computational Design and Analysis of a Transonic Natural Laminar Flow Wing for a Wind Tunnel Model

A natural laminar flow (NLF) wind tunnel model has been designed and analyzed for a wind tunnel test in the National Transonic Facility (NTF) at the NASA Langley Research Center. The NLF design method is built into the CDISC design module and uses a Navier-Stokes flow solver, a boundary layer profile solver, and stability analysis and transition prediction software. The NLF design method alters the pressure distribution to support laminar flow on the upper surface of wings with high sweep and flight Reynolds numbers. The method addresses transition due to attachment line contamination/transition, Gortler vortices, and crossflow and Tollmien-Schlichting modal instabilities. The design method is applied to the wing of the Common Research Model (CRM) at transonic flight conditions. Computational analysis predicts significant extents of laminar flow on the wing upper surface, which results in drag savings. A 5.2 percent scale semispan model of the CRM NLF wing will be built and tested in the NTF. This test will aim to validate the NLF design method, as well as characterize the laminar flow testing capabilities in the wind tunnel facility.

Lynde, Michelle N.↗

NASA NTRS2017

Building a Practical Natural Laminar Flow Design Capability

A preliminary natural laminar flow (NLF) design method that has been developed and applied to supersonic and transonic wings with moderate-to-high leading-edge sweeps at flight Reynolds numbers is further extended and evaluated in this paper. The modular design approach uses a knowledge-based design module linked with different flow solvers and boundary layer stability analysis methods to provide a multifidelity capability for NLF analysis and design. An assessment of the effects of different options for stability analysis is included using pressures and geometry from an NLF wing designed for the Common Research Model (CRM). Several extensions to the design module are described, including multiple new approaches to design for controlling attachment line contamination and transition. Finally, a modification to the NLF design algorithm that allows independent control of Tollmien-Schlichting (TS) and cross flow (CF) modes is proposed. A preliminary evaluation of the TS-only option applied to the design of an NLF nacelle for the CRM is performed that includes the use of a low-fidelity stability analysis directly in the design module.

Campbell, Richard L.↗

NASA NTRS2016

Expanding the Natural Laminar Flow Boundary for Supersonic Transports

A computational design and analysis methodology is being developed to design a vehicle that can support significant regions of natural laminar flow (NLF) at supersonic flight conditions. The methodology is built in the CDISC design module to be used in this paper with the flow solvers Cart3D and USM3D, and the transition prediction modules BLSTA3D and LASTRAC. The NLF design technique prescribes a target pressure distribution for an existing geometry based on relationships between modal instability wave growth and pressure gradients. The modal instability wave growths (both on- and off-axes crossflow and Tollmien-Schlichting) are balanced to produce a pressure distribution that will have a theoretical maximum NLF region for a given streamwise wing station. An example application is presented showing the methodology on a generic supersonic transport wingbody configuration. The configuration has been successfully redesigned to support significant regions of NLF (approximately 40% of the wing upper surface by surface area). Computational analysis predicts NLF with transition Reynolds numbers (ReT) as high as 36 million with 72 degrees of leading-edge sweep (ΛLE), significantly expanding the current boundary of ReT - ΛLE combinations for NLF. This NLF geometry provides a total drag savings of 4.3 counts compared to the baseline wing-body configuration (approximately 5% of total drag). Off-design evaluations at near-cruise and low-speed, high-lift conditions are discussed, as well as attachment line contamination/transition concerns. This computational NLF design effort is a part of an ongoing cooperative agreement between NASA and JAXA researchers.

Lynde, Michelle N.↗

NASA NTRS2016

Natural Laminar Flow Design for Wings with Moderate Sweep

A new method for the aerodynamic design of wings with natural laminar flow is under development at the NASA Langley Research Center. The approach involves the addition of new flow constraints to an existing knowledge-based design module for use with advanced flow solvers. The uniqueness of the new approach lies in the tailoring of target pressure distributions to achieve laminar flow on transonic wings with leading-edge sweeps and Reynolds numbers typical of current transports. The method is demonstrated on the Common Research Model configuration at critical N-factor levels representative of both flight and high-Reynolds number wind tunnel turbulence levels. The design results for the flight conditions matched the target extent of laminar flow very well. The design at wind tunnel conditions raised some design issues that prompted further improvements in the method, but overall has given promising results.

Campbell, Richard L.↗