Engineering topics

Ma, Beihai

Publications and source records attributed to Ma, Beihai.

6 records

DOE OSTI2024

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Development of Ti 3 SiC 2 MAX phase tubular structures for solar receiver applications

Solar receiver tubes are key components of concentrating solar-thermal power (CSP) systems that harvest solar energy. For better efficiency, the Gen3 CSP receivers, which collect heat into a heat transfer fluid, require a temperature exceeding 700 °C during operation and need to perform under extreme conditions of high temperature and high thermal stress. Operators are seeking CSP designs using new high-temperature structural materials with high thermal conductivity and high creep resistance to achieve a design life of 30 years and thus help recover the plant capital cost sooner. MAX phase materials, which consist of an early transition metal element, an A-group element, and carbon or nitrogen, are expected to exhibit high creep resistance as well as high fracture toughness. Here, in this paper, we describe fabricating both (1) dense Ti 3 SiC 2 MAX phase disks and (2) short-length tubes using field-assisted sintering technology (FAST). First, the disk samples that we fabricated are fully dense and contain ≈90 % Ti 3 SiC 2 MAX phase materials and ≈10 % TiC phase materials. We determined a flexure strength of 519 ± 32 MPa by conducting a four-point bending test at room temperature with rectangular bar samples of ≈100 % density. The thermal conductivity of the Ti 3 SiC 2 MAX phase samples, measured by light flashing analysis, decreases linearly from a value of 41 W . m -1 . K -1 at room temperature to a value of 36 W . m -1 . K -1 at 650 °C. A solar reflectance measurement of the Ti 3 SiC 2 MAX phase revealed that, temperature increases from 400 to 1400 °C, thermal emittance increases from 0.39 to 0.49, while selectivity decreases from 1.8 to 1.4, respectively. Whereas the surface oxidized MAX phase samples after 100 h exposure to air at 1000 °C exhibit that of SiC. Next, we discuss fabrication of the crack-free Ti 3 SiC 2 MAX phase tubular structures accomplished by using FAST processing in graphite bedding. A Ti 3 SiC 2 MAX phase content of > 95 % with traceable ≈3% remaining TiC phase and ≈15 % porosity were demonstrated after high-temperature annealing. An average fracture strength of ≈250 MPa was determined with Ti 3 SiC 2 MAX phase tubes of ≈85 % density by diametral compression testing at room temperature. Our work demonstrated that using FAST processing to produce Ti 3 SiC 2 MAX phase tubular structures for CSP receiver applications is a viable approach.

14 SOLAR ENERGY↗

DOE OSTI2023

Concurrent reaction-bonded joining and densification of additively manufactured silicon carbide by liquid silicon infiltration

Here, in this study, additive-manufactured silicon carbide preforms were joined and densified by reaction bonding via liquid silicon infiltration. The silicon carbide preforms were first printed by binder jetting additive manufacturing. To demonstrate concurrent joining and densification, two preforms with carbon or parchment papers at the interface were concurrently joined and infiltrated by liquid silicon. Results showed a robust interface with thicknesses ranging from 150 to 500 µm, depending on the paper type and the number of paper layers. High-energy synchrotron X-ray revealed that β-phase silicon carbide was formed inside the interface. Finally, two additively manufactured samples with complicated channel geometry were successfully joined. Energy dispersive spectroscopy of the interface of the channeled samples showed a consistent and robust joining. This concurrent approach of joining and densification enables efficiency improvement of fabricating silicon carbide parts with complicated geometries and widens geometry freedom for additive manufacturing of silicon carbide.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Role of Fe Doping on Local Structure and Electrical and Magnetic Properties of PbTiO 3

In this work, the local structure and multiferroic properties of iron-doped lead titanate (PbTi 1-x Fe x O 3-δ ) samples was investigated over the entire composition range (x = 0-1). Inherent polarization in PbTiO 3 decreases due to Fe 3+ incorporation up to the solubility limit (x similar to 0.3), although homogeneous doping persists only up to x = 0.1. Ti prefers highly distorted oxygen octahedra for any x value, while Fe prefers more symmetric O-deficient polyhedra (Fe-O n ). The charge compensating oxygen vacancies induce local tilting of the Fe-O n polyhedra beyond a critical x value (x ≥ 0.2), promoting magnetic interaction between two adjacent Fe atoms. The strain induced by local heterogeneity could act as a coupling force between magnetic and ferroelectric properties. Fe-rich clusters evolve into ferromagnetic PbFe 12 O 19 with increased Fe doping. PbTi 1-x Fe x O 3-δ (x ≥ 0.3) samples therefore have separate origins for the ferroelectric (PbTi 1-x Fe x O 3-δ ) and magnetic (PbFe 12 O 19 ) phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Method for making metal-nanostructured carbon composites

A method for making covetic metal-nanostructured carbon composites or compositions is described herein. This method is advantageous, in that it provides substantially oxygen-free covetic materials and allows precise control of the composition of the covetic material to be produced. The method comprises introducing carbon into a molten metal in a heated reactor under low oxygen partial pressure, while passing an electric current through the molten metal. The reactor is heated at a temperature sufficient to form a network of nanostructured carbon within a matrix of the metal. After heating the covetic material is recovered from the reactor.

Balachandran, Uthamalingam↗

DOE OSTI2020

Method for making metal-carbon composites and compositions

A method for making covetic metal-carbon composites or compositions by electron beam melt heating under vacuum (pressure <10−3 Torr) is described herein. This fabrication method is advantageous, in that it provides oxygen-free covetic materials in a process that allows precise control of the composition of the covetic material to be produced. The method described herein also can be applied to produce multi-element-carbon composites within a metal or alloy matrix, including high melting temperature materials such as ceramic particles or prefabricated nano- or micro-structures, such as carbon nanotubes or graphene compounds. The covetic reaction between metal and carbon takes place under the influence of flowing electrons through the melted metal-carbon precursor. This process creates strong bonding between nanocarbon structure and the metal elements in the melt.

36 MATERIALS SCIENCE↗