Search NASA⌕ Search

Engineering topics

Ma, Dong

Publications and source records attributed to Ma, Dong.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Progression of creep deformation from grain boundaries to grain interior in Al-Cu-Mn-Zr alloys

Creep mechanisms are studied in θ'-Al 2 Cu-strengthened Al-Cu-Mn-Zr alloys at 300 and 350°C for (i) ACMZ, a base alloy without further alloying elements and (ii) RR350, a commercial alloy with additions of Ni and Co forming distinct grain-boundary precipitates. At high stresses, creep is dominated by dislocations bypassing θ' precipitates within grains via the Orowan mechanism, as evidenced by (i) very high stress exponent (n~20-25) and (ii) α-Al and θ' lattice strains (measured via in-situ neutron diffraction) evolving during creep in a manner consistent with load transfer from the plastically-deforming α-Al matrix to elastically-deforming θ' precipitates. At intermediate stresses, both alloys exhibit a n~3 regime, where α-Al and θ' lattice strains scale near-linearly with applied stress while remaining largely unaffected by strain accumulation, indicating that Orowan looping or dislocation pile-up around θ' is now inactive within the grains. Rather, dislocation motion occurs solely in θ'-precipitate-free zones (θ'-PFZ) where high dislocation densities are observed via TEM after creep deformation. Plastic flow at θ'-PFZ and/or localized pipe diffusion are expected to enable grain-boundary sliding (GBS), which is proposed as the rate-limiting mechanism in the n~3 regime. Ni/Co-rich precipitates at RR350 grain-boundaries, with negligible θ'-PFZ around them, share load (as determined via neutron diffraction) with the α-Al matrix more effectively than θ-Al 2 Cu precipitates at ACMZ grain-boundaries, with wide surrounding θ'-PFZ. So, high creep resistance in the n~3 GBS regime of RR350 is enabled by coarsening-resistant grain-boundary precipitates, forming without concomitant development of weak θ'-PFZ, which effectively share load with the grains.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Medium-Range Ordering in the Ionic Glass Electrolytes LiPON and LiSiPON

In this work, we provide an in-depth structural characterization of the amorphous ionic glasses LiPON and LiSiPON with high Li content. Based on ab initio molecular dynamics simulations, the structure of these materials is an inverted structure with either isolated polyanion tetrahedra or polyanion dimers in a Li+ matrix. Based on neutron scattering data, this type of inverted structure leads to a significant amount of medium-range ordering in the structure, as demonstrated by two sharp diffraction peaks and a periodic structural oscillation in the density function G(r). While this medium-range ordering is commonly observed in liquids and metallic glasses, it has not previously been observed in oxides. On a local scale, adding N and Si increases the number of anion bridges and polyanion dimer structures, leading to higher ionic conductivity. In the medium-range ordering, the addition of Si leads to more disorder in the polyanion substructure but a significant increase in the ordering of the O substructure. Finally, we demonstrate that this inverted structure with medium-range ordering results in a glassy material that is both mechanically stiff and ductile on the nanoscale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Dislocation-θ' (Al2Cu) interactions during creep deformation of an Al-Cu alloy

While precipitate-dislocation interactions are well-understood for Al-Cu alloys in tension, creep behavior has seen far less study. New, thermally-stabilized Al-Cu alloys have θ' (Al 2 Cu) as strengthening precipitates that remain stable up to 300 °C (~60% of the melting temperature) and higher, where creep becomes essential to the mechanical behavior. This investigation identifies the precipitate-dislocation interactions in such an Al-Cu alloy using in-situ neutron diffraction and scanning transmission electron microscopy. Significant load transfer to the θ' precipitates occurs, which can be attributed to dislocation loops on the interfaces of θ' and the Al matrix. Thus, Orowan looping is identified to be the primary activity for precipitate-dislocation interactions. As Orowan looping and load transfer are associated with significant strain hardening, these results explain the excellent creep resistance seen in this alloy, and provide insights into the design of precipitation strengthened alloys with superior creep performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ neutron diffraction study of fatigue behavior of CrFeCoNiMo 0.2 high entropy alloy

In situ neutron diffraction measurement was applied to study the low-cycle fatigue behavior of CrFeCoNiMo 0.2 high entropy alloy. A two-step stress-controlled fatigue test with a stress range of 100–460 and 20–500 MPa was employed. The as-cast sample was cycled 129,000 and 61,000 times, respectively, before fracture. The evolution of the lattice strain and peak intensity demonstrates that the main deformation mechanism is dislocation slip, while no evidence of stacking fault was found. A three-stage ratcheting was clearly observed. Under the stress-controlled mode, the experimentally determined dislocation density increases linearly with the ratcheting strain. Here, the increase of the dislocation density results in a decay of the ratcheting strain rate, which stabilizes the structure and is beneficial for fatigue resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In Situ Scattering Studies of Crystallization Kinetics in a Phase-Separated Zr–Cu–Fe–Al Bulk Metallic Glass

In this work, thermal stability and the crystallization kinetics of a phase-separated Zr-Cu-Fe-Al bulk metallic glass were investigated using in situ high-energy synchrotron X-ray and neutron diffraction, as well as small-angle synchrotron X-ray scattering. It was revealed that this glass with excellent glass-forming ability possesses a two-step crystallization behavior. The crystalline products and their evolution sequence are more complicated than a homogeneous Zr-Cu-Al glass with average glass-forming ability. The experimental results indicate that a finely distributed nanometer-sized cubic Zr 2 Cu phase forms first and then transforms to a tetragonal Zr 2 Cu phase, while the matrix transforms to an orthorhombic Zr3Fe phase. The strength of the Zr-Cu-Fe-Al composite containing cubic Zr 2 Cu phase and glass matrix increases, and the plasticity also improves compared to the as-cast Zr-Cu-Fe-Al bulk metallic glass. Our results suggest that the formation of multiple and complex crystalline products would be the characteristics of the Zr-Cu-Fe-Al glass with better glass-forming ability. Our study may shed light on the synthesis of bulk-sized glass-nanocrystals composites of high strength and good plasticity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High-throughput design of high-performance lightweight high-entropy alloys

Developing affordable and light high-temperature materials alternative to Ni-base superalloys has significantly increased the efforts in designing advanced ferritic superalloys. However, currently developed ferritic superalloys still exhibit low high-temperature strengths, which limits their usage. Here we use a CALPHAD-based high-throughput computational method to design light, strong, and low-cost high-entropy alloys for elevated-temperature applications. Through the high-throughput screening, precipitation-strengthened lightweight high-entropy alloys are discovered from thousands of initial compositions, which exhibit enhanced strengths compared to other counterparts at room and elevated temperatures. The experimental and theoretical understanding of both successful and failed cases in their strengthening mechanisms and order-disorder transitions further improves the accuracy of the thermodynamic database of the discovered alloy system. This study shows that integrating high-throughput screening, multiscale modeling, and experimental validation proves to be efficient and useful in accelerating the discovery of advanced precipitation-strengthened structural materials tuned by the high-entropy alloy concept.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Crystallographic orientation-dependent strain hardening in a precipitation-strengthened Al-Cu alloy

While the strengthening of Al-Cu alloys due to precipitation has been extensively studied, the effect of crystallographic orientation of the matrix and precipitates, as well as precipitate morphology, on the strain hardening behavior is not well understood. In this paper, we investigate this effect with in situ neutron diffraction during deformation of an Al-Cu alloy (206) after multiple aging treatments. Precipitate-dislocation interactions were found to change from precipitate shearing for microstructures predominantly containing GPI and θ" precipitates to Orowan looping for microstructures with primarily θ' and θ precipitates. Notably, significant anisotropy in strain hardening behavior was observed when θ' precipitates were present, which was attributed to crystallographic orientation dependent load transfer from the Al matrix to the θ' precipitates. The anisotropic load transfer is hypothesized to be caused by the extent of rotation of high aspect-ratio θ' precipitates, owing to dislocations looping around them during plastic deformation of the matrix. Predictions from an analytical model describing the anisotropic magnitude of load transfer from precipitate rotation agree well with experimental results, successfully validating the precipitate rotation hypothesis and explaining the anisotropic strain hardening behavior. This model allows for the prediction of stresses separately in the precipitate and matrix phases as a function of crystallographic orientation, only given the bulk mechanical properties.

36 MATERIALS SCIENCE↗