Search NASA⌕ Search

Engineering topics

Ma, T.

Publications and source records attributed to Ma, T..

At least 73 records · Page 4

Calibration of proton dispersion for the NIF electron positron proton spectrometer (NEPPS) for short-pulse laser experiments on the NIF ARC

Experiments using the Advanced Radiographic Capability (ARC) laser at the National Ignition Facility (NIF) aim to characterize short-pulse-driven proton beams for use as both probes and drivers for high-energy-density physics experiments. Measurements of ARC-driven proton beam characteristics, such as energy spectrum and conversion efficiency, rely on the NIF Electron Positron Proton Spectrometer (NEPPS). The NEPPS diagnostic is a version of an existing particle spectrometer which is used for detecting MeV electron and positron spectra via permanent magnetic field dispersion. These spectrometers have not yet been calibrated for protons and instead use an analytical calculation to estimate the dispersion. Small variations in the field uniformity can affect the proton dispersion due to the relatively small resolving power (E/dE) for this diagnostic. A broadband energy, laser-accelerated proton source was produced at the Titan laser to experimentally calibrate the proton dispersion. These experimental data were used to test the theoretical dispersion. Numerical simulations using measurements of the magnetic field variation within the diagnostic were used to obtain a realistic proton dispersion curve for the new NEPPS units. In conclusion, this procedure for obtaining each independent dispersion is applicable to all EPPS and NEPPS diagnostics, given the axial magnetic field profile.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-Performance Indirect-Drive Cryogenic Implosions at High Adiabat on the National Ignition Facility

To reach the pressures and densities required for ignition, it may be necessary to develop an approach to design that makes it easier for simulations to guide experiments. Here, we report on a new short-pulse inertial confinement fusion platform that is specifically designed to be more predictable. Furthermore, the platform has demonstrated 99%+0.5% laser coupling into the hohlraum, high implosion velocity (411 km/s), high hotspot pressure (220+60 Gbar), and high cold fuel areal density compression ratio (>400), while maintaining controlled implosion symmetry, providing a promising new physics platform to study ignition physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermal Temperature Measurements of Inertial Fusion Implosions

Accurate measurement of the thermal temperature in inertially confined fusion plasmas is essential for characterizing ignition performance and validating the basic physics understanding of the stagnation conditions. Here we present experimental results from cryogenic deuterium-tritium implosions on the National Ignition Facility using a differential filter spectrometer designed to measure the thermal electron temperature from x-ray continuum emission from the stagnated plasma. Furthermore, electron temperature measurements, used in conjunction with the Doppler-broadened DT neutron spectra, allow one to infer the partition of energy in the hot spot between internal energy and unconverted kinetic energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Using multiple x-ray emission images of inertially confined implosions to identify spatial variations and estimate confinement volumes (invited)

We describe two methods to analyze multiple x-ray images of a small, self-emitting object, and we apply these methods to the stagnating hotspots in inertial confinement fusion experiments. The first method, the common integrated profile, can be employed to assess and quantify spatial variations in opacity. It is both a simple assessment of consistency and a sophisticated measurement of variations in a region that is otherwise difficult to observe. Second, we present a method to estimate volumes of highly asymmetric objects using multiple images of x-ray emission. The method is based on image intensities and does not require any explicit assumption of symmetry

47 OTHER INSTRUMENTATION↗

Computational modeling of proton acceleration with multi-picosecond and high energy, kilojoule, lasers

Here, we use computational modeling to investigate proton beam generation from kilojoule, multi-picosecond laser pulses pertinent to several recently commissioned, large-scale laser facilities. The dependencies of proton acceleration on electron source parameters including pulse duration, temperature, and flux are independently and systematically evaluated. Proton acceleration is found to depend not only on the source size and peak temperature of the injected electrons but also on the rate of increase for a more physical time-varying temperature. Simulations of a 10 ps, sub-relativistic intensity (8 × 10 17 W/cm 2 ) at 1 μm wavelength laser pulse show that energetic electrons generated within the expanding under-dense laser-produced plasma sustain the proton acceleration for ~20 ps. This results in 15 MeV energy gain of the protons, well above what would be predicted based on conventional intensity scalings or what has been observed with shorter pulses. Using this prolonged acceleration, a scheme consisting of a 1 ps and 10 ps double pulse is shown to further boost proton maximum energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The influence of hohlraum dynamics on implosion symmetry in indirect drive inertial confinement fusion experiments

High laser energy (>1.2 MJ) implosion experiments on the National Ignition Facility show that low mode implosion symmetry is highly dependent on an expanding high-Z wall “bubble” plasma feature. The bubble is caused by the early time deposition of laser beams incident on the interior near the entrance of the cylindrical hohlraum (outer cone beams). It absorbs beams designated for the waist of the hohlraum (inner cone beams) causing a redistribution of x-ray flux on the capsule. From measurements, we are able to quantify the absorption and expansion of this bubble. Measurements show that the resulting hot spot is more oblate when there is more inner beam absorption in the bubble. We also find absorption in the bubble to be between 51 ± 3% and 62 ± 2%. This bubble absorption is found to evolve predictably as a function of the early time outer cone laser pulse fluence and the pulse length. From this, a phenomenological model of the effective drive symmetry and subsequent implosion shape is found indicating a very strong dependence of implosion shape on early time laser fluence and laser pulse duration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fusion Energy Output Greater than the Kinetic Energy of an Imploding Shell at the National Ignition Facility

A series of cryogenic, layered deuterium-tritium (DT) implosions have produced, for the first time, fusion energy output twice the peak kinetic energy of the imploding shell. These experiments at the National Ignition Facility utilized high density carbon ablators with a three-shock laser pulse (1.5 MJ in 7.5 ns) to irradiate low gas-filled ( 0.3 mg / cc of helium) bare depleted uranium hohlraums, resulting in a peak hohlraum radiative temperature ~ 290 eV . The imploding shell, composed of the nonablated high density carbon and the DT cryogenic layer, is, thus, driven to velocity on the order of 380 km / s resulting in a peak kinetic energy of ~ 21 kJ , which once stagnated produced a total DT neutron yield of 1.9 × 10 16 (shot N170827) corresponding to an output fusion energy of 54 kJ. Time dependent low mode asymmetries that limited further progress of implosions have now been controlled, leading to an increased compression of the hot spot. Finally, it resulted in hot spot areal density ( ρr ~ 0.3 g / cm 2 ) and stagnation pressure ( ~ 360 Gbar ) never before achieved in a laboratory experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurement of temperature and density using non-collective X-ray Thomson scattering in pulsed power produced warm dense plasmas

We present the first experimental measurement of temperature and density of a warm dense plasma produced by a pulsed power driver at the Nevada Terawatt Facility (NTF). In the early phases of discharge, most of the mass remains in the core, and it has been challenging to diagnose with traditional methods, e.g. optical probing, because of the high density and low temperature. Accurate knowledge of the transport coefficients as well as the thermodynamic state of the plasma is important to precisely test or develop theoretical models. Here, we have used spectrally resolved non-collective X-ray Thomson scattering to characterize the dense core region. We used a graphite load driven by the Zebra current generator (0.6 MA in 200 ns rise time) and the Ti He-α line produced by irradiating a Ti target with the Leopard laser (30 J, 0.8 ns) as an X-ray probing source. Using this configuration, we obtained a signal-to-noise ratio ~2.5 for the scattered signal. Finally, by fitting the experimental data with predicted spectra, we measured T = 2±1.9 eV, ρ = 0.6±0.5 gr/cc, 70 ns into the current pulse. The complexity of the dense core is revealed by the electrons in the dense core that are found to be degenerate and weakly coupled, while the ions remain highly coupled.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A near one-dimensional indirectly driven implosion at convergence ratio 30

Inertial confinement fusion cryogenic-layered implosions at the National Ignition Facility, while successfully demonstrating self-heating due to alpha-particle deposition, have fallen short of the performance predicted by one-dimensional (1D) multi-physics implosion simulations. The current understanding, from experimental evidence as well as simulations, suggests that engineering features such as the capsule tent and fill tube, as well as time-dependent low-mode asymmetry, are to blame for the lack of agreement. A short series of experiments designed specifically to avoid these degradations to the implosion are described here in order to understand if, once they are removed, a high-convergence cryogenic-layered deuterium-tritium implosion can achieve the 1D simulated performance. The result is a cryogenic layered implosion, round at stagnation, that matches closely the performance predicted by 1D simulations. This agreement can then be exploited to examine the sensitivity of approximations in the model to the constraints imposed by the data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Variable convergence liquid layer implosions on the National Ignition Facility

Liquid layer implosions using the “wetted foam” technique, where the liquid fuel is wicked into a supporting foam, have been recently conducted on the National Ignition Facility for the first time [Olson et al., Phys. Rev. Lett. 117, 245001 (2016)]. In this paper, we report on a series of wetted foam implosions where the convergence ratio was varied between 12 and 20. Reduced nuclear performance is observed as convergence ratio increases. 2-D radiation-hydrodynamics simulations accurately capture the performance at convergence ratios (CR) ~ 12, but we observe a significant discrepancy at CR ~ 20. Finally, this may be due to suppressed hot-spot formation or an anomalous energy loss mechanism.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Relativistic electron-positron plasma jets and interactions using LFEX lasers

Relativistic pair plasmas and jets are believed to exist in many astrophysical objects [Wardle 1998, Weidenspointner 2008] and are invoked to explain energetic phenomena related to Gamma Ray Bursts, Black Holes and the heating of intergalactic medium (IGM) [Mirabel & Rodriguez 1999, Meszaros 2002].

42 ENGINEERING↗

Simplified model of pinhole imaging for quantifying systematic errors in image shape

In this paper, we examine systematic errors in x-ray imaging by pinhole optics for quantifying uncertainties in the measurement of convergence and asymmetry in inertial confinement fusion implosions. We present a quantitative model for the total resolution of a pinhole optic with an imaging detector that more effectively describes the effect of diffraction than models that treat geometry and diffraction as independent. This model can be used to predict loss of shape detail due to imaging across the transition from geometric to diffractive optics. We find that fractional error in observable shapes is proportional to the total resolution element we present and inversely proportional to the length scale of the asymmetry being observed. Finally, we have experimentally validated our results by imaging a single object with differently sized pinholes and with different magnifications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On the importance of minimizing “coast-time” in x-ray driven inertially confined fusion implosions

By the time an inertially confined fusion (ICF) implosion has converged a factor of 20, its surface area has shrunk 400×, making it an inefficient x-ray energy absorber. So, ICF implosions are traditionally designed to have the laser drive shut off at a time, toff, well before bang-time, tBT, for a coast-time of tcoast=tBT−toff>1 ns. High-foot implosions on NIF showed a strong dependence of many key ICF performance quantities on reduced coast-time (by extending the duration of laser power after the peak power is first reached), most notably stagnation pressure and fusion yield. Herein we show that the ablation pressure, pabl, which drives high-foot implosions, is essentially triangular in temporal shape, and that reducing tcoast boosts pabl by as much as ∼2× prior to stagnation thus increasing fuel and hot-spot compression and implosion speed. One-dimensional simulations are used to track hydrodynamic characteristics for implosions with various coast-times and various assumed rates of hohlraum cooling after toff to illustrate how the late-time conditions exterior to the implosion can impact the fusion performance. A simple rocket model-like analytic theory demonstrates that reducing coast-time can lead to a ∼15% higher implosion velocity because the reduction in x-ray absorption efficiency at late-time is somewhat compensated by small (∼5%−10%) ablator mass remaining. Together with the increased ablation pressure, the additional implosion speed for short coast-time implosions can boost the stagnation pressure by ∼2× as compared to a longer coast-time version of the same implosion. Four key dimensionless parameters are identified and we find that reducing coast-time to as little as 500 ps still provides some benefit. Finally, we show how the high-foot implosion data is consistent with the above mentioned picture.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of extremely strong shock waves in solids launched by petawatt laser heating

Understanding hydrodynamic phenomena driven by fast electron heating is important for a range of applications including fast electron collimation schemes for fast ignition and the production and study of hot, dense matter. In this work, detailed numerical simulations modelling the heating, hydrodynamic evolution, and extreme ultra-violet (XUV) emission in combination with experimental XUV images indicate shock waves of exceptional strength (200 Mbar) launched due to rapid heating of materials via a petawatt laser. In conclusion, we discuss in detail the production of synthetic XUV images and how they assist us in interpreting experimental XUV images captured at 256 eV using a multi-layer spherical mirror.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗