Search NASA⌕ Search

Engineering topics

Ma, Wei

Publications and source records attributed to Ma, Wei.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A butterfly-shaped acceptor with rigid skeleton and unique assembly enables both efficient organic photovoltaics and high-speed organic photodetectors

ABSTRACT It remains challenging to design efficient bifunctional semiconductor materials in organic photovoltaic and photodetector devices. Here, we report a butterfly-shaped molecule, named WD-6, which exhibits low energy disorder and small reorganization energy due to its enhanced molecular rigidity and unique assembly with strong intermolecular interaction. The binary photovoltaic device based on PM6:WD-6 achieved an efficiency of 18.41%. Notably, an efficiency of 19.42% was achieved for the ternary device based on PM6:BTP-eC9:WD-6. Moreover, the photodetection device based on WD-6 demonstrated an ultrafast response speed (205 ns response time at λ of 820 nm) and a high cutoff frequency of −3 dB (2.45 MHz), surpassing the values of most commercial Si photodiodes. Based on these findings, we showcased an application of the WD-6-based photodetection device in high-speed optical communication. These results offer valuable insights into the design of organic semiconductor materials capable of simultaneously exhibiting high photovoltaic and photodetective performance.

Science & Technology - Other Topics↗
DOE OSTI2024

Regulation of Side‐Chain Symmetry for Delaying Triplet Formation and Suppressing Non‐Radiative Loss in Organic Solar Cells

Abstract The structural revolutions of non‐fullerene acceptors (NFAs) have driven continuous efficiency breakthroughs in organic solar cells (OSCs). Rational regulation of NFA structures toward efficient exciton dissociation and mitigated non‐radiative recombination is pivotal for OSCs. The incorporation of asymmetric side chains on NFAs can often achieve these goals by inducing a desirable aggregate state. However, it lacks the studies to directly correlate the side‐chain symmetry of NFAs with the exciton delocalization and triplet dynamics in OSCs. Herein, The influence of structural symmetry on the aggregate properties is systematically investigated and exciton/charge dynamics based on two developed biaxial‐conjugated NFAs with varied side‐chain symmetry. The symmetric NFA having diverse molecular packing orientations can form multiple charge transfer channels in its blend with polymer donor, which cannot be found in that comprising the asymmetric ones. Moreover, a slower rate and lower ratio of the spin‐triplet state are formed in the blend of symmetric NFA, resulting in a much lower non‐radiative voltage loss in corresponding OSCs. This study reveals the distinct advantages of symmetric NFAs in both aggregate properties and exciton/charge dynamics over those of asymmetric ones, paving the way for developing high‐performance OSCs using easier‐to‐prepare, low‐cost symmetric materials.

Chemistry↗
DOE OSTI2024

Halogenated Dibenzo[ f , h ]quinoxaline Units Constructed 2D‐Conjugated Guest Acceptors for 19% Efficiency Organic Solar Cells

Abstract Halogenation of Y‐series small‐molecule acceptors (Y‐SMAs) is identified as an effective strategy to optimize photoelectric properties for achieving improved power‐conversion‐efficiencies (PCEs) in binary organic solar cells (OSCs). However, the effect of different halogenation in the 2D‐structured large π‐fused core of guest Y‐SMAs on ternary OSCs has not yet been systematically studied. Herein, four 2D‐conjugated Y‐SMAs (X‐QTP‐4F, including halogen‐free H‐QTP‐4F, chlorinated Cl‐QTP‐4F, brominated Br‐QTP‐4F, and iodinated I‐QTP‐4F) by attaching different halogens into 2D‐conjugation extended dibenzo[ f , h ]quinoxaline core are developed. Among these X‐QTP‐4F, Cl‐QTP‐4F has a higher absorption coefficient, optimized molecular crystallinity and packing, suitable cascade energy levels, and complementary absorption with PM6:L8‐BO host. Moreover, among ternary PM6:L8‐BO:X‐QTP‐4F blends, PM6:L8‐BO:Cl‐QTP‐4F obtains a more uniform and size‐suitable fibrillary network morphology, improved molecular crystallinity and packing, as well as optimized vertical phase distribution, thus boosting charge generation, transport, extraction, and suppressing energy loss of OSCs. Consequently, the PM6:L8‐BO:Cl‐QTP‐4F‐based OSCs achieve a 19.0% efficiency, which is among the state‐of‐the‐art OSCs based on 2D‐conjugated Y‐SMAs and superior to these devices based on PM6:L8‐BO host (17.70%) and with guests of H‐QTP‐4F (18.23%), Br‐QTP‐4F (18.39%), and I‐QTP‐4F (17.62%). The work indicates that halogenation in 2D‐structured dibenzo[ f , h ]quinoxaline core of Y‐SMAs guests is a promising strategy to gain efficient ternary OSCs.

14 SOLAR ENERGY↗
DOE OSTI2024

A Difluoro‐Methoxylated Ending‐Group Asymmetric Small Molecule Acceptor Lead Efficient Binary Organic Photovoltaic Blend

Abstract Developing a new end group for synthesizing asymmetric small molecule acceptors (SMAs) is crucial for achieving high‐performance organic photovoltaics (OPVs). Herein, an asymmetric small molecule acceptor, BTP‐BO‐4FO, featuring a new difluoro‐methoxylated end‐group is reported. Compared to its symmetric counterpart L8‐BO, BTP‐BO‐4FO exhibits an upshifted energy level, larger dipole moment, and more sequential crystallinity. By adopting two representative and widely available solvent additives (1‐chloronaphthalene (CN) and 1,8‐diiodooctane (DIO)), the device based on PM6:BTP‐BO‐4FO (CN) photovoltaic blend demonstrates a power conversion efficiency (PCE) of 18.62% with an excellent open‐circuit voltage (V OC ) of 0.933 V, which surpasses the optimal result of L8‐BO. The PCE of 18.62% realizes the best efficiencies for binary OPVs based on SMAs with asymmetric end groups. A series of investigations reveal that optimized PM6:BTP‐BO‐4FO film demonstrates similar molecular packing motif and fibrillar phase distribution as PM6:L8‐BO (DIO) does, resulting in comparable recombination dynamics, thus, similar fill factor. Besides, it is found PM6:BTP‐BO‐4FO possesses more efficient charge generation, which yields betterV OC –J SC balance. This study provides a new ending group that enables a cutting‐edge efficiency in asymmetric SMA‐based OPVs, enriching the material library and shed light on further design ideas.

Chemistry↗
DOE OSTI2024

Elucidate the Thermal Degradation Mechanism of Y6‐Based Organic Solar Cells by Establishing Structure‐Property Correlation

Abstract Organic solar cells (OSCs) achieved performance booming benefiting from the emerging of non‐fullerene acceptors, while inadequate device stability hampers their further application. At present, the prevalent belief attributes the inevitable thermal degradation of OSC device to morphological instability caused by excessive phase separation and crystallization in the active layer during device operation. However, it is inapplicable for state‐of‐art Y6‐based devices which strongly degrade before large‐scale morphology change. Herein, an alternative degradation mechanism is elucidated wherein molecular orientation change and demixing induced performance degradation in Y6‐based devices. Distinct from IT‐4F‐based counterpart, Y6‐based devices suffer severe thermal degradation dominated by open‐circuit voltage (V OC ) and fill factor (FF) losses. TheV OC loss is attributed to molecular orientation transition of polymer donors from edge‐on to face‐on, leading to a strong built‐in potential reduction and increase in non‐radiative loss due to energy level shifting. As forFFdecay, discontinuous acceptor phases result in electron mobility decrease by over orders of magnitude, originating from the increased molecular stacking and phase separation. This work reveals the thermal degradation mechanism for Y6‐based devices and correlates the photoelectric properties with morphology instability, which will offer guidance for improving the stability of high‐performance OSCs.

Chemistry↗
DOE OSTI2024

A Pseudo Planar Heterojunction Structure for Eco‐Friendly Printable Organic Solar Cells Achieving 19.05% Efficiency

Abstract Obtaining a well‐accurate vertical distribution active layer morphology through the air‐printing process is an essential task for achieving efficient scalable large‐area organic solar cells (OSCs). In this target, the desired and controllable pseudo planar heterojunction (PPHJ) active layer structure with suitable phase separation is developed by pre‐deposited D18‐Cl layer under the PM6:BTP‐eC9 film via an eco‐friendly manufacturing method. The addition of the D18‐Cl regulates molecular crystallization and leads to an ideal vertical stratification while simultaneously suppressing voltage loss, optimizing energetic disorder, and carrier management. Impressively, the optimal PPHJ devices perform superior power conversion efficiencies (PCEs) of 19.05% (100 nm), 17.33% (300 nm), and 14.14% (4 cm 2 ) compared to the BHJ devices. Importantly, the PPHJ OSCs also exhibit an impressive extrapolated T 80 (the time required to reach 80% of initial PCE) of long‐time storage and operational stability, as well as thermal stability.

Chemistry↗
DOE OSTI2024

On the role of asymmetric molecular geometry in high-performance organic solar cells

Although asymmetric molecular design has been widely demonstrated effective for organic photovoltaics (OPVs), the correlation between asymmetric molecular geometry and their optoelectronic properties is still unclear. To access this issue, we have designed and synthesized several symmetric-asymmetric non-fullerene acceptors (NFAs) pairs with identical physical and optoelectronic properties. Interestingly, we found that the asymmetric NFAs universally exhibited increased open-circuit voltage compared to their symmetric counterparts, due to the reduced non-radiative charge recombination. From our molecular-dynamic simulations, the asymmetric NFA naturally exhibits more diverse molecular interaction patterns at the donor (D):acceptor (A) interface as compared to the symmetric ones, as well as higher D:A interfacial charge-transfer state energy. Moreover, it is observed that the asymmetric structure can effectively suppress triplet state formation. These advantages enable a best efficiency of 18.80%, which is one of the champion results among binary OPVs. Therefore, this work unambiguously demonstrates the unique advantage of asymmetric molecular geometry, unveils the underlying mechanism, and highlights the manipulation of D:A interface as an important consideration for future molecular design.

14 SOLAR ENERGY↗
DOE OSTI2024

Eliminating the Burn‐in Loss of Efficiency in Organic Solar Cells by Applying Dimer Acceptors as Supramolecular Stabilizers

Abstract The meta‐stable active layer morphology of organic solar cells (OSCs) is identified as the main cause of the rapid burn‐in loss of power conversion efficiency (PCE) during long‐term device operation. However, effective strategies to eliminate the associated loss mechanisms from the initial stage of device operation are still lacking, especially for high‐efficiency material systems. Herein, the introduction of molecularly engineered dimer acceptors with adjustable thermal transition properties into the active layer of OSCs to serve as supramolecular stabilizers for regulating the thermal transitions and optimizing the crystallization of the absorber composites is reported. By establishing intimate π‐π interactions with small‐molecule acceptors, these stabilizers can effectively reduce the trap‐state density (N t ) in the devices to achieve excellent PCEs over 19%. More importantly, the lowN t associated with an initially optimized morphology can be maintained under external stresses to significantly reduce the PCE burn‐in loss in devices. This research reveals a judicious approach to improving OPV stability by establishing a comprehensive correlation between material properties, active‐layer morphology, and device performance, for developing burn‐in‐free OSCs.

Chemistry↗
DOE OSTI2024

Balancing Flexible Side Chains on 2D Conjugated Acceptors Enables High‐Performance Organic Solar Cell

Abstract Balancing the rigid backbones and flexible side chains of light‐harvesting materials is crucially important to reach optimized intermolecular packing, micromorphology, and thus photovoltaic performance of organic solar cells (OSCs). Herein, based on a distinctive CH‐series acceptor platform with 2D conjugation extended backbones, a series of nonfullerene acceptors (CH‐6F‐Cn) are synthesized by delicately tuning the lengths of flexible side chains fromn‐octyl ton‐amyl. A systemic investigation has revealed that the variation of the side chain's length can not only modulate intermolecular packing modes and crystallinity but also dramatically improve the micromorphology of the active layer and eventual photovoltaic parameters of OSCs. Consequently, the highest PCE of 18.73% can be achieved by OSCs employingD18:PM6:CH‐6F‐C8as light‐harvesting materials.

Chemistry↗
DOE OSTI2024

Identifying and Amplifying the Spontaneously Formed Photo‐Charge Contribution in Opaque and Semitransparent Organic Photovoltaics

Abstract Spontaneous photo‐charge (SP) generation within the non‐fullerene (NFA) bulk helps avoid exciton (EX) related loss as compared to the traditional heterojunction route in organic solar cells (OSCs). Unfortunately, the promising SP utilization attracts little attention at this time due to the lack of knowledge on its specific contribution to the photovoltaic performance and rational optimization in high‐efficiency devices. To fill the gap, the NFAs’ SP characteristics are related with their photocurrent loss and power conversion efficiency (PCE) in state‐of‐the‐art materials. Though higher SP population is good for efficient EX utilization, it simultaneously acts as an additional photo‐charge recombination channel. The former can be further enhanced by increasing the NFAs’ crystallinity with preferred lamellar growth, and the latter can be suppressed via electric doping. With the aid of the two‐step optimization strategy, the total photocurrent loss is reduced from 14.4% to 4.8%, accompanying with PCE increment from 16.9% to 18.5%. The SP utilization strategy is finally applied in the semitransparent OSCs (ST‐OSCs), due to its less heterojunction area sensitive photo‐charge generation characteristic. A light utilization efficiency (LUE) is then increased from 3.21% to 3.77%. The findings highlight the pursue of efficient SP utilization as a new design philosophy in future OSCs’ progresses.

Chemistry↗
DOE OSTI2024

Carboxylating Elastomer via Thiol‐Ene Click Reaction to Improve Miscibility with Conjugated Polymers for Mechanically Robust Organic Solar Cells with Efficiency of 19%

Abstract Incorporating flexible insulating polymers is a straightforward strategy to enhance the mechanical properties of rigid conjugated polymers, enabling their use in flexible electronic devices. However, maintaining electronic characteristics simultaneously is challenging due to the poor miscibility between insulating polymers and conjugated polymers. This study introduces the carboxylation of insulating polymers as an effective strategy to enhance miscibility with conjugated polymers via surface energy modulation and hydrogen bonding. The carboxylated elastomer, synthesized via a thiol‐ene click reaction, closely matches the surface energy of the conjugated polymer. This significantly improves the mechanical properties, achieving a high crack‐onset strain of 21.48%, surpassing that (5.93%) of the unmodified elastomer:conjugated polymer blend. Upon incorporating the carboxylated elastomer into PM6:L8‐BO‐based organic solar cells, an impressive power conversion efficiency of 19.04% is attained, which top‐performs among insulating polymer‐incorporated devices and outperforms devices with unmodified elastomer or neat PM6:L8‐BO. The superior efficiency is attributed to the optimized microstructures and enhanced crystallinity for efficient and balanced charge transport, and suppressed charge recombination. Furthermore, flexible devices with 5% carboxylated elastomer exhibit superior mechanical stability, retaining ≈88.9% of the initial efficiency after 40 000 bending cycles at a 1 mm radius, surpassing ≈83.5% for devices with 5% unmodified elastomer.

Chemistry↗
DOE OSTI2024

High‐Performance Ternary Organic Solar Cells with Enhanced Luminescence Efficiency and Miscibility Enabled by Two Compatible Acceptors

Abstract The ternary strategy has proven to be an effective method for improving the efficiency of organic solar cells (OSCs). However, designing and selecting the third component still pose challenges. In this study, this issue is addressed by focusing on the PBDB‐T:Y18‐F binary system and introducing a new, strong luminescent, asymmetric small‐molecule acceptor (SMA) called L8‐CBIC‐Cl, which shares a similar skeleton with Y18‐F. The similarity in molecular framework facilitates good compatibility between the two acceptors, resulting in the formation of an alloy‐like acceptor phase. Furthermore, the norbornenyl‐modified end group in L8‐CBIC‐Cl contributes to its strong luminescent properties, which in turn leads to a low non‐radiative energy loss and a high open‐circuit voltage. Consequently, the PBDB‐T:L8‐CBIC‐Cl:Y18‐F based ternary devices realize a high power conversion efficiency (PCE) up to 17.01%, which is higher than PBDB‐T:Y18‐F device (14.49%). Importantly, L8‐CBIC‐Cl exhibits a good universality as a guest acceptor in other three binary systems (D18:Y6, D18:BTP‐eC9‐4F, and D18:L8‐BO). The D18:L8‐BO:L8‐CBIC‐Cl device shows an impressive efficiency of 19%. The work demonstrates that employing SMA with a high PLQY and better miscibility with host acceptor as the third component has a great potential for developing high‐efficiency ternary OSCs.

Chemistry↗
DOE OSTI2023

Regime-Dependence of Nocturnal Nitrate Formation via N 2 O 5 Hydrolysis and Its Implication for Mitigating Nitrate Pollution

The heterogeneous hydrolysis of dinitrogen pentoxide (N 2 O 5 ) is an important pathway in nitrate formation; however, its formation rate and relative contribution to total particulate nitrate (pNO 3 - ) are highly variable. Here we report that nocturnal pNO 3 - formation via N 2 O 5 hydrolysis is dependent on the regime defined by the ratio of NO 2 to O 3 . Nocturnal pNO 3 - formation via N 2 O 5 hydrolysis is suppressed in an O 3 -limited regime but enhanced in a NO 2 -limited regime. The results have crucial implications for effective control of nitrate pollution in the future. An exclusive decrease in NO 2 will decrease nocturnal pNO 3 - formation in a NO 2 -limited regime but may be less effective or even increase nocturnal pNO 3 - formation in an O 3 -limited regime.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Nonfullerene Acceptor Featuring Unique Self‐Regulation Effect for Organic Solar Cells with 19 % Efficiency

Abstract The blend nanomorphology of electron‐donor (D) and ‐acceptor (A) materials is of vital importance to achieving highly efficient organic solar cells. Exogenous additives especially aromatic additives are always needed to further optimize the nanomorphology of blend films, which is hardly compatible with industrial manufacture. Herein, we proposed a unique approach to meticulously modulate the aggregation behavior of NFAs in both crystal and thin film nanomorphology via self‐regulation effect. Nonfullerene acceptor Z9 was designed and synthesized by tethering phenyl groups on the inner side chains of the Y6 backbone. Compared with Y6, the tethered phenyl groups participated in the molecular aggregation via the π–π stacking of phenyl‐phenyl and phenyl‐2‐(5,6‐difluoro‐3‐oxo‐2,3‐dihydro‐1H‐inden‐1‐ylidene)malononitrile (IC‐2F) groups, which induced 3D charge transport with phenyl‐mediated super‐exchange electron coupling. Moreover, ordered molecular packing with suitable phase separation was observed in Z9‐based blend films. High power conversion efficiencies (PCEs) of 19.0 % (certified PCE of 18.6 %) for Z9‐based devices were achieved without additives, indicating the great potential of the self‐regulation strategy in NFA design.

Chemistry↗
DOE OSTI2023

Green-Solvent Processed Blade-Coating Organic Solar Cells with an Efficiency Approaching 19% Enabled by Alkyl-Tailored Acceptors

Power-conversion-efficiencies (PCEs) of organic solar cells (OSCs) in laboratory, normally processed by spin-coating technology with toxic halogenated solvents, have reached over 19%. However, there is usually a marked PCE drop when the blade-coating and/or green-solvents toward large-scale printing are used instead, which hampers the practical development of OSCs. Here, a new series of N-alkyl-tailored small molecule acceptors named YR-SeNF with a same molecular main backbone are developed by combining selenium-fused central-core and naphthalene-fused end-group. Thanks to the N-alkyl engineering, NIR-absorbing YR-SeNF series show different crystallinity, packing patterns, and miscibility with polymeric donor. The studies exhibit that the molecular packing, crystallinity, and vertical distribution of active layer morphologies are well optimized by introducing newly designed guest acceptor associated with tailored N-alkyl chains, providing the improved charge transfer dynamics and stability for the PM6:L8-BO:YR-SeNF-based OSCs. As a result, a record-high PCE approaching 19% is achieved in the blade-coating OSCs fabricated from a green-solvent o-xylene with high-boiling point. Notably, ternary OSCs offer robust operating stability under maximum-power-point tracking and well-keep > 80% of the initial PCEs for even over 400 h. Our alkyl-tailored guest acceptor strategy provides a unique approach to develop green-solvent and blade-coating processed high-efficiency and operating stable OSCs, which paves a way for industrial development.

14 SOLAR ENERGY↗
DOE OSTI2023

Auxiliary sequential deposition enables 19%-efficiency organic solar cells processed from halogen-free solvents

High-efficiency organic solar cells are often achieved using toxic halogenated solvents and additives that are constrained in organic solar cells industry. Therefore, it is important to develop materials or processing methods that enabled highly efficient organic solar cells processed by halogen free solvents. In this paper, we report an innovative processing method named auxiliary sequential deposition that enables 19%-efficiency organic solar cells processed by halogen free solvents. Our auxiliary sequential deposition method is different from the conventional blend casting or sequential deposition methods in that it involves an additional casting of dithieno[3,2-b:2’,3’-d]thiophene between the sequential depositions of the donor (D18-Cl) and acceptor (L8-BO) layers. The auxiliary sequential deposition method enables dramatic performance enhancement from 15% to over 18% compared to the blend casting and sequential deposition methods. Furthermore, by incorporating a branched-chain-engineered acceptor called L8-BO-X, device performance can be boosted to over 19% due to increased intermolecular packing, representing top-tier values for green-solvent processed organic solar cells. Comprehensive morphological and time-resolved characterizations reveal that the superior blend morphology achieved through the auxiliary sequential deposition method promotes charge generation while simultaneously suppressing charge recombination. This research underscores the potential of the auxiliary sequential deposition method for fabricating highly efficient organic solar cells using environmentally friendly solvents.

14 SOLAR ENERGY↗
DOE OSTI2023

Correlation of Broad Absorption Band with Small Singlet‐Triplet Energy Gap in Organic Photovoltaics

Abstract Organic photovoltaics (OPV) are one of the most effective ways to harvest renewable solar energy, with the power conversion efficiency (PCE) of the devices soaring above 19 % when processed with halogenated solvents. The superior photocurrent of OPV over other emerging photovoltaics offers more opportunities to further improve the efficiency. Tailoring the absorption band of photoactive materials is an effective way to further enhance OPV photocurrent. However, the field has mostly been focusing on improving the near‐infrared region photo‐response, with the absorption shoulders in short‐wavelength region (SWR) usually being neglected. Herein, by developing a series of non‐fullerene acceptors (NFAs) with varied side‐group conjugations, we observe an enhanced SWR absorption band with increased side‐group conjugation length. The underpinning factors of how molecular structures and geometries improve SWR absorption are clearly elucidated through theoretical modelling and crystallography. Moreover, a clear relationship between the enhanced SWR absorption and reduced singlet‐triplet energy gap is established, both of which are favorable for the OPV performance and can be tailored by rational structure design of NFAs. Finally, the rationally designed NFA, BO‐TTBr, affords a decent PCE of 18.5 % when processed with a non‐halogenated green solvent.

Chemistry↗