Search NASA⌕ Search

Engineering topics

Ma, Wei

Publications and source records attributed to Ma, Wei.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

N-dopants optimize the utilization of spontaneously formed photocharges in organic solar cells

Non-fullerene acceptors (NFAs) not only bring rapid efficiency progress to organic solar cells (OSCs) but have also generated scientific interest in re-evaluating the photocharge generation route via spontaneous or heterojunction-assisted charge separation. In this work, we propose the addition of n-dopants as a strategy to optimize the utilization of spontaneously formed photocharges in NFAs and construct ultralow donor-content dilute bulk heterojunction (BHJ) devices to validate the dopant's roles. N-dopants enhance the transport length of spontaneously formed photocharges over twofold and alleviate the bimolecular recombination with balanced carrier mobility during charge extraction. This improves the photocurrent of ultralow donor-content dilute BHJ devices by over 2.4 times. Moreover, these benefits are successfully conducted to the BHJ devices, and enhancement of conversion efficiencies is observed in both the 100 nm and 400 nm thick OSCs. Our results provide a feasible way to optimize the intrinsic photocharges in NFAs and renew the possibility of efficient single-component OSCs as inorganic photovoltaic techniques.

14 SOLAR ENERGY↗
DOE OSTI2022

Enhance the performance of organic solar cells by nonfused ring electron acceptors bearing a pendent perylenediimide group

A new nonfused ring electron acceptor PDI-DO-2F is designed and synthesized by attaching perylenediimide (PDI) unit as a pendent group to the central donor core. Compared with the control molecule DO-2F, the introduction of PDI lateral substituent can greatly enhance the solubility and decrease the crystallinity of the resulted acceptor. The PBDB-T:PDI-DO-2F blend film exhibits a much better morphology with higher and more balanced carrier mobility in contrast to PBDB-T:DO-2F one. PDI-DO-2F based organic solar cells (OSCs) give a power conversion efficiency (PCE) of 11.78%, higher than DO-2F based ones (9.82%). Furthermore, PDI-DO-2F based OSCs shows a ΔE non-rad value of 0.23 eV, which is significantly lower than the DO-2F based ones (0.28 eV). More importantly, the addition of PDI-DO-2F as the third component to the PBDB-T:DO-2F binary system can optimize the morphology of blend films and improve the shelf stability of devices. Finally, the PBDB-T:DO-2F:PDI-DO-2F based ternary OSCs achieve a higher PCE of 13.82%.

14 SOLAR ENERGY↗
DOE OSTI2022

High‐Performance Green Thick‐Film Ternary Organic Solar Cells Enabled by Crystallinity Regulation

Abstract The power conversion efficiency (PCE) of organic solar cells (OSCs) has reached high values of over 19%. However, most of the high‐efficiency OSCs are fabricated by spin‐coating with toxic solvents and the optimal photoactive layer thickness is limited to 100 nm, limiting practical development of OSCs. It is a great challenge to obtain ideal morphology for high‐efficiency thick‐film OSCs when using non‐halogenated solvents due to the unfavorable film formation kinetics. Herein, high‐efficiency ternary thick‐film (300 nm) OSCs with PCE of 15.4% based on PM6:BTR‐Cl:CH1007 are fabricated by hot slot‐die coating using non‐halogenated solvent (o‐xylene) in the air. Compared to PM6:BTR‐Cl:Y6 blends, the stronger pre‐aggregation of CH1007 in solution induces the earlier aggregation of CH1007 molecules and longer aggregation time, and thus results in high and balanced crystallinity of donors and acceptor in CH1007‐based ternary film, which led to high‐carrier mobility and suppressed charge recombination. The ternary strategy is further used to fabricate high‐efficiency, thick‐film, large‐area, and flexible devices processed from non‐halogenated solvents, paving the way for industrial development of OSCs.

Chemistry↗
DOE OSTI2022

Over 31% efficient indoor organic photovoltaics enabled by simultaneously reduced trap-assisted recombination and non-radiative recombination voltage loss

Indoor organic photovoltaics (OPVs) have shown great potential application in driving low-energy-consumption electronics for the Internet of Things. There is still great room for further improving the power conversion efficiency (PCE) of indoor OPVs, considering that the desired morphology of the active layer to reduce trap-assisted recombination and voltage losses and thus simultaneously enhance the fill factor (FF) and open-circuit voltage for efficient indoor OPVs remains obscure. Herein, by optimizing the bulk and interface morphology via a layer-by-layer (LBL) processing strategy, low leakage current and low non-radiative recombination loss can be synergistically achieved in PM6:Y6-O based devices. Detailed characterizations reveal the stronger crystallinity, purer domains and ideal interfacial contacts in the LBL devices compared to their bulk-heterojunction (BHJ) counterparts. The optimized morphology yields a reduced voltage loss and an impressive FF of 81.5%, and thus contributes to a high PCE of 31.2% under a 1000 lux light-emitting diode (LED) illumination in the LBL devices, which is the best reported efficiency for indoor OPVs. Additionally, this LBL strategy exhibits great universality in promoting the performance of indoor OPVs, as exemplified by three other non-fullerene acceptor systems. Finally, this work provides guidelines for morphology optimization and synergistically promotes the fast development of efficient indoor OPVs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quasi‐Homojunction Organic Nonfullerene Photovoltaics Featuring Fundamentals Distinct from Bulk Heterojunctions

Abstract In contrast to classical bulk heterojunction (BHJ) in organic solar cells (OSCs), the quasi‐homojunction (QHJ) with extremely low donor content (≤10 wt.%) is unusual and generally yields much lower device efficiency. Here, representative polymer donors and nonfullerene acceptors are selected to fabricate QHJ OSCs, and a complete picture for the operation mechanisms of high‐efficiency QHJ devices is illustrated. PTB7‐Th:Y6 QHJ devices at donor:acceptor (D:A) ratios of 1:8 or 1:20 can achieve 95% or 64% of the efficiency obtained from its BHJ counterpart at the optimal D:A ratio of 1:1.2, respectively, whereas QHJ devices with other donors or acceptors suffer from rapid roll‐off of efficiency when the donors are diluted. Through device physics and photophysics analyses, it is observed that a large portion of free charges can be intrinsically generated in the neat Y6 domains rather than at the D/A interface. Y6 also serves as an ambipolar transport channel, so that hole transport as also mainly through Y6 phase. The key role of PTB7‐Th is primarily to reduce charge recombination, likely assisted by enhancing quadrupolar fields within Y6 itself, rather than the previously thought principal roles of light absorption, exciton splitting, and hole transport.

Chemistry↗
DOE OSTI2022

Enhancing exciton diffusion by reducing energy disorder in organic solar cells

A highly crystalline, highly emissive, and wide-bandgap polymer AC174 with an extremely small Stokes shift is designed and synthesized in water, and is used to reduce system energetic disorder and increase the exciton diffusion length of the classical PM6:Y6 blend system. AC174 is incompatible with PM6 and Y6, improves molecular packing, and reduces system energetic disorder. The long-range Förster resonance energy transfer between the donor and acceptor is enhanced, and the exciton diffusion constant and exciton lifetime are increased, leading to a longer exciton diffusion length and more efficient exciton dissociation and charge generation. The addition of AC174 simultaneously improves the open-circuit voltage, short-circuit current density (J SC ) and fill factor of PM6:Y6 devices; especially the highest internal quantum efficiency approaches 100%, and the highest J SC is 28.4 mA cm –2 . Ternary devices with 5% AC174 in the donors achieve a power conversion efficiency of 17.2%, higher than those of the parent binary devices based on PM6:Y6 (15.9%) and AC174:Y6 (3.24%).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Donor End-Capped Alkyl Chain Length Dependent Non-Radiative Energy Loss in All-Small-Molecule Organic Solar Cells

A critical bottleneck for further efficiency breakthroughs in organic solar cells (OSCs) is to minimize the non-radiative energy loss (eΔV nr ) while maximizing the charge generation. With the development of highly emissive low-bandgap non-fullerene acceptors, the design of high-performance donors becomes critical to enable the blend with the electroluminescence quantum efficiency to approach or surpass the pristine acceptor. Herein, by shortening the end-capped alkyl chains of the small-molecular donors from hexyl (MPhS-C6) to ethyl (MPhS-C2), the material obtained aggregation that was insensitive to thermal annealing (TA) along with condensed packing simultaneously. The former leads to small phase separation and suppressed upshifts of the highest occupied molecular orbital energy level during TA, and the latter facilitates its efficient charge-transport at aggregation-less packing. Hence, the ΔV nr decreases from 0.242 to 0.182 V, from MPhS-C6 to MPhS-C2 based OSCs. An excellent PCE of 17.11% is obtained by 1,8-diiodoctane addition due to almost unchanged high J sc (26.6 mA cm –2 ) and V oc (0.888 V) with improved fill factor, which is the record efficiency with the smallest energy loss (0.497 eV) and ΔV nr (0.192 V) in all-small-molecule OSCs. Finally, these results emphasize the potential material design direction of obtaining concurrent TA-insensitive aggregation and condensed packing to maximize the device performances with a super low ΔV nr .

36 MATERIALS SCIENCE↗
DOE OSTI2022

High performance polymerized small molecule acceptor by synergistic optimization on $\pi$-bridge linker and side chain

The polymerized small-molecule acceptors have attracted great attention for application as polymer acceptor in all-polymer solar cells recently. The modification of small molecule acceptor building block and the π-bridge linker is an effective strategy to improve the photovoltaic performance of the polymer acceptors. In this work, we synthesized a new polymer acceptor PG-IT2F which is a modification of the representative polymer acceptor PY-IT by replacing its upper linear alkyl side chains on the small molecule building block with branched alkyl chains and attaching difluorene substituents on its thiophene π-bridge linker. Through this synergistic optimization, PG-IT2F possesses more suitable phase separation, increased charge transportation, better exciton dissociation, lower bimolecular recombination, and longer charge transfer state lifetime than PY-IT in their polymer solar cells with PM6 as polymer donor. Therefore, the devices based on PM6:PG-IT2F demonstrated a high power conversion efficiency of 17.24%, which is one of the highest efficiency reported for the binary all polymer solar cells to date. This work indicates that the synergistic regulation of small molecule acceptor building block and π-bridge linker plays a key role in designing and developing highly efficient polymer acceptors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Simultaneously Enhancing Exciton/Charge Transport in Organic Solar Cells by an Organoboron Additive

Efficient exciton diffusion and charge transport play a vital role in advancing the power conversion efficiency (PCE) of organic solar cells (OSCs). Here, a facile strategy is presented to simultaneously enhance exciton/charge transport of the widely studied PM6:Y6-based OSCs by employing highly emissive trans-bis(dimesitylboron)stilbene (BBS) as a solid additive. BBS transforms the emissive sites from a more H-type aggregate into a more J-type aggregate, which benefits the resonance energy transfer for PM6 exciton diffusion and energy transfer from PM6 to Y6. Transient gated photoluminescence spectroscopy measurements indicate that addition of BBS improves the exciton diffusion coefficient of PM6 and the dissociation of PM6 excitons in the PM6:Y6:BBS film. Transient absorption spectroscopy measurements confirm faster charge generation in PM6:Y6:BBS. Moreover, BBS helps improve Y6 crystallization, and current-sensing atomic force microscopy characterization reveals an improved charge-carrier diffusion length in PM6:Y6:BBS. Finally, owing to the enhanced exciton diffusion, exciton dissociation, charge generation, and charge transport, as well as reduced charge recombination and energy loss, a higher PCE of 17.6% with simultaneously improved open-circuit voltage, short-circuit current density, and fill factor is achieved for the PM6:Y6:BBS devices compared to the devices without BBS (16.2%).

14 SOLAR ENERGY↗
DOE OSTI2022

Flexible organic integrated electronics for self-powered multiplexed ocular monitoring

Smart contact lens has drawn extensive research interests due to the noninvasive real-time detection of the human body to provide biomedical information for health management. However, it has been difficult to accurately measure the physiological signals in tears, and the use of external power source has also hindered the future applications. Here, we demonstrated an organic electrochemical transistor based multiplexed sensors self-powered by the organic solar cells (OSCs). The integrated device was fabricated via simple process including solution blade-coating and thermal evaporation. OSCs were optimized to provide optimal operation voltage for the sensors that exhibit semilog-linear response to the glucose and calcium ions in tear fluids without any peripheral circuits. The sensing signals can be transmitted to the laptop wirelessly through a near filed communication unit. This integrated self-powered multiplexed sensing device will provide real-time monitoring of the biomarkers in tears, prospected to be installed on the smart contact lens for the early detection and diagnosis of diabetes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Solid additive engineering enables high-efficiency and eco-friendly all-polymer solar cells

Currently, morphology optimization of all-polymer solar cells (all-PSCs) strongly depends on the use of solvent additives, which are usually highly toxic and harmful to the environment and human health. Here, we report a green and volatile solid additive, 2-methoxynaphthalene (2-MN). It was found that the incorporation of 2-MN into a PM6:PY-DT blend can effectively manipulate the aggregations of PM6 and PY-DT during film depositing and thermal annealing processes and results in highly ordered molecular packing and favorable phase-separated morphology. Consequently, a record-high efficiency of 17.32% is achieved for the PM6:PY-DT device. Moreover, 2-MN-processed all-PSCs were fabricated by using non-halogenated solvent. High efficiencies of 17.03% and 16.67% are obtained for all-PSCs fabricated under nitrogen atmosphere and ambient conditions, respectively. Finally, our work shows that the utilization of 2-MN as a green and solid additive is a simple and feasible strategy to optimize the morphology and sheds new light on eco-friendly fabrication and application of all-PSCs.

14 SOLAR ENERGY↗
DOE OSTI2022

Electrical edge effect induced photocurrent overestimation in low-light organic photovoltaics

In many literatures, the short-circuit current (J SC ) of indoor organic photovoltaics is overestimated, leading to severely wrong device performance evaluation and analysis. In this work, based on the equivalent circuit model, we demonstrate that electrical edge effect is sensitive to both transverse surface resistance and light intensity. At low light intensity, the electrical edge effect could lead to J SC being significantly overestimated, i.e., by 100% and even more. We show that for a PM6:Y6 device capped with a MoOX layer, when measured under 0.01 sun, the usually overlooked interface doping mechanism would lead to J SC and PCE overestimation by 51% and 15%, respectively. Besides, we show that the magnitude of J SC overestimation drastically increases with high photoactive-layer surface roughness. This work emphasized the significant electrical edge effect on J SC evaluations for low-light solar cells and is conducive to understanding the intrinsic mechanism of edge effect, promoting a healthier development of organic photovoltaics.

14 SOLAR ENERGY↗