Search NASA⌕ Search

Engineering topics

Ma, Xiaotu

Publications and source records attributed to Ma, Xiaotu.

At least 19 records

Recycled graphite enabled superior performance for lithium ion batteries

Recycling graphite attracts growing attention since cumulative amount of spent Li-ion batteries and the shortage of graphite supply chain. Although various recycling methods have been reported, the recycled graphite cannot reach the strict commercial standards of purity, scalability, efficiency, and capacity, preventing it from battery manufacturing. Herein, the important roles of defects and functional groups on the graphite surface are deeply studied, and a closed-loop graphite recycling process with the surface recovery and modification for the graphite from the end-of-life batteries is demonstrated. The recovered graphite delivers a purity of over 99.9 % and an average initial coulombic efficiency of 91.5 %. Compared with commercial graphite in industrial standard battery testing parameters, full cells with recovered graphite possess enhanced rate reversibility, doubled cycle life, over 10 % higher capacity along with half anode material cost. In conclusion, these impressive results not only underscore the transformative potential of surface reconstruction and modification in graphite recycling, but also present economic feasibility and sustainable pathway for significantly improving battery performance and addressing global resource challenges via integration with the hydrometallurgical recycling process.

25 ENERGY STORAGE↗

Acid Etching‐Driven Self‐Assembly of Mn‐Shell Inducing Rock‐Salt Phase for Enhanced Single‐Crystal Ni‐Rich Cathodes

With the wide adoption of Li‐ion batteries, Ni‐rich cathode is considered as one of the most promising candidates of cathodes due to its high energy density and low cost. However, stability decreased with increasing Ni content in the Ni‐rich cathode. To solve this bottleneck, many strategies, such as coating, doping, surface modification, and special morphologies, have been developed. Herein, we introduce a groundbreaking approach for enhancing Ni‐rich cathode through an innovative acid etching process that promotes Mn shell self‐assembly, inducing a rock‐salt phase on the surface. This method not only simplifies the Ni‐rich cathode modification process, but also significantly improves the structural stability and electrochemical performance of Ni‐rich cathode. Our findings demonstrate that developed single‐crystal Ni‐rich cathode shows 3–34 % better stability compared to both commercial modified Ni‐rich cathode and unmodified counterparts. The unique Mn shell effectively mitigates reversible phase shifts during cycling, contributing to a remarkable enhancement in cycling stability. Additionally, this novel fabrication technique paves the way for cost‐effective production of high‐performance cathode materials, offering substantial benefits for lithium‐ion battery technology. And this study proves the potential of this method in advancing the design and development of durable, high‐capacity cathode materials for next‐generation batteries.

Ni-rich cathode↗

Understanding the Effects of Bi Modification on the Properties of Ni-Rich Cathodes

With the skyrocketing market demands for energy storage, lithium ions batteries (LIB) with higher energy density are urgently needed. Cathodes play a critical role in determining the energy density of LIB, and the most popular one is Ni-rich cathode due to its high capacity. However, due to the fast structural degradation, Ni-rich cathode materials should be further modified to achieve higher stability. Herein, we introduce bismuth ions in LiNi 0.83 Co 0.11 Mn 0.06 O 2 cathodes by adding Bi 2 O 3 during sintering to optimize the specific capacity and cycle stability. By adding 0.1% mol Bi, the Li + diffusion and structural stability are effectively optimized, leading to improved electrochemical performances. Further, the modified sample delivers much higher specific capacity (222.9 mAhg -1 , 0.05 C) than unmodified sample (204 mAhg -1 , 0.05 C). Meanwhile, the specific capacity of optimized sample after 100 cycles at 0.33 C is 27.75 mAhg -1 higher than that of unmodified sample. Therefore, this work demonstrates that Bi modification can be regarded as a possible solution to optimizing the electrochemical performance of Ni-rich cathodes.

25 ENERGY STORAGE↗

Facile etching for single crystal cathode materials

A recycling and synthesis of charge material for secondary batteries generates single-crystal charge materials for producing batteries with greater charge cycle longevity. Charge material particles undergo a heating for fusing or enhancing grain boundaries between polycrystalline particles. The resulting, more well-defined grain boundaries are easily etched by a relatively weak mineral acid solution. The acid solution removes material at the grain boundaries to separate secondary particles into primary particles along the grain boundaries. The resulting single crystal (monocrystalline) charge material particles are washed and filtered, and typically re-sintered to accommodate any needed lithium (lithium carbonate), and result in a charge material with larger surface area, higher lithium diffusivity and lower cation ordering.

Wang, Yan↗

Regulating Anionic Redox via Mg Substitution in Mn-Rich Layered Oxide Cathodes Enabling High Electrochemical Stability for Sodium-Ion Batteries

Here, with the limited resources and high cost of lithium-ion batteries (LIBs) and the ever-increasing market demands, sodium-ion batteries (SIBs) gain much interest due to their economical sustainability, and similar chemistry and manufacturing processes to LIBs. As cathodes play a vital role in determining the energy density of SIBs, Mn-based layered oxides are promising cathodes due to their low cost, environmental friendliness, and high theoretical capacity. However, the main challenge is structural instability upon cycling at high voltage. Herein, Mg is introduced into the P2-type Na 0.62 Ni 0.25 Mn 0.75 O 2 cathode to enhance electrochemical stability. By combining electrochemical testing and material characterizations, it is found that substituting 10 mol% Mg can effectively alleviate the P2–O2 phase transition, Jahn-Teller distortion, and irreversible oxygen redox. Moreover, structural integrity is greatly improved. These lead to enhanced electrochemical performances. With the optimized sample, a remarkable capacity retention of 92% in the half cell after 100 cycles and 95% in the full cell after 170 cycles can be achieved. Altogether, this work provides an alternative way to stabilize P2-type Mn-based layer oxide cathodes, which in turn, put forward the development of this material for the next-generation SIBs.

25 ENERGY STORAGE↗

Roll-to-roll solvent-free manufactured electrodes for fast-charging batteries

In response to the growing demand for lithium-ion batteries (LIBs), we demonstrate a solvent-free manufacturing technology that can avoid toxic organic solvents and form unique electrode structures to overcome the bottlenecks in low costs and fast charging. The lower tortuosity achieved by the open pores in the dry-printed (DP) electrode allows for a shorter Li+ diffusion pathway, which leads to better rate performance. The DP pouch cells exhibit higher capacity retention of 78% and 69% at 3C and 4C, respectively, compared with 67% and 52% for the slurry cast (SL) cells at the same rates. Moreover, the coating layer on the surface of active materials prevents the excess side reaction between active materials and electrolytes, which prolongs the cycle life of the DP cells. This manufacturing process is a roll-to-roll system with immense potential to be scaled up, providing a more efficient and economical way for battery manufacturing.

36 MATERIALS SCIENCE↗

Modeling assisted synthesis of Zr-doped Li 3-x In 1-x Zr x Cl 6 with ultrahigh ionic conductivity for lithium-ion batteries

All-solid-state lithium-ion batteries (ASSLBs) are an important milestone for the future of energy storage because of their capability of impressive energy density and outstanding safety. However, oxide and sulfide solid-state electrolytes (SSEs) suffer from either low ionic conductivity or poor chemical stability. In contrast, halide-based SSEs, are promising as candidate materials owing to high conductivity, good stability, and broad cathode compatibility. Though element doping of the SSEs is an effective and common approach to further improve their electrochemical properties, dopant exploration and optimization through solely experimental trials are both costly and time-consuming. For this aspect, computational simulations for dopant element and concentration screening are adopted in this research and zirconium is selected as a suitable dopant for Li 3 InCl 6 . Further, the synthesized Li 2.75 In 0.75 Zr 0.25 Cl 6 exhibited Li ionic conductivity of 5.82 x 10 -3 Scm -1 at room temperature, which is the highest among reported halide SSEs. The ASSLB formed with Li 2 CoO 2 -Li 2.75 In 0.75 Zr 0.25 Cl 6 -Li/In delivers a high initial capacity of 129.3 mAh∙g -1 . Conclusively, this work provides an effective approach which combines computational modeling and experimental verification for the development of halide SSEs with improved stability and conductivity. The successful design approach and compelling results provide further possibilities and capabilities in future SSE research.

25 ENERGY STORAGE↗

A green closed-loop process for selective recycling of lithium from spent lithium-ion batteries

As the economy started to recover from the COVID pandemic, the price of Li 2 CO 3 skyrocketed to its highest. This situation has aggravated concerns about the supply chain for lithium-ion batteries (LIBs). Recycling spent LIBs is a potential solution to alleviate the bottleneck of the supply chain and prevent environmental pollution, and has attracted lots of attention. However, lithium recycling is generally disregarded because of the complex recycling process and its low recycling efficiency. Here, in this work we developed a sustainable lithium recovery process, which can selectively leach and recover lithium with formic acid before recycling valuable metals. With the reported method, lithium can be 99.8% recovered from layered oxide cathode materials with 99.994% purity. In addition, this lithium recovery process is affordable, compared to the typical hydrometallurgical process, by saving 11.15% per kilogram of spent LIBs. Therefore, this research provided a new solution to eliminating the effects of lithium ions on valuable metal separation and the co-precipitation reaction and precluding the influence of other metal ions on lithium recovery. Finally, this simplified lithium recovery process provides new opportunities for sustainable recycling of LIBs and economical restoration of the lithium supply chain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Achieving High Stability and Performance in P2-Type Mn-Based Layered Oxides with Tetravalent Cations for Sodium-Ion Batteries

We report P2-type sodium-manganese-based layered cathodes, owing to their high capacity from both cationic and anionic redox, are a potential candidate for Na-ion batteries to replace Li-ion technology in certain applications. Still, the structure instability originates from irreversible oxygen redox at high voltage remains a challenge. Here, a high sustainability cobalt-free P2- Na 0.72 Mn 0.75 Li 0.24 X 0.01 O 2 (X= Ti/Si) cathode is developed. The outstanding capacity retention and voltage retention after 150 cycles are obtained in Na half-cells. Our finding shows Ti locates on the surface while Si diffuses to the bulk of the particles. Thus, Ti can act as protective layer that alleviate side reactions in carbonate-based electrolyte. Meanwhile, Si can regulate the local electronic structure and suppress oxygen redox activities. Notably, full-cells with hard carbon (≈300-335 Whkg -1 based on the cathode mass) deliver the capacity retention of 83% for P2- Na 0.72 Mn 0.75 Li 0.24 Si 0.01 O 2 and 66% for P2-Na 0.72 Mn 0.75 Li 0.24 Ti 0.01 O 2 after 500 cycles; this electrochemical stability is the best compared to other reported cathodes based on oxygen redox at present. The superior cycle performance also stems from the ability to inhibit microcracking and planar gliding within the particles. Altogether, this finding offers new composition towards developing high performance low-cost cathodes for Na-ion batteries and highlights the unique role of Ti/Si ions.

25 ENERGY STORAGE↗

Upgrading the Performance and Stability of Lithium, Manganese-Rich Layered Oxide Cathodes with Combined-Formic Acid and Spinel Coating Treatment

We report improving sluggish rate performance and cycling stability of Li, Mn-rich cathode materials (LMR) is of great importance for practical implementation. Here, dual surface modification on LMR particles with formic acid washing and spinel coating improves the electrochemical performance. Dilute formic acid can remove the Li2CO3 surface impurities and selectively reduce Ni while significantly increasing specific surface area by ~32 %, unlocking more electrochemically active surfaces. Spinel coating enhances cycle stability by suppressing detrimental side reactions at electrode-electrolyte interfaces at high voltage. Post-annealing temperature was found to significantly affect the cathode performance. Higher temperature favors diffusion of transition metal (TM)/Li ions of the spinel coating from surface to the bulk, removing the coating by possible reconstruction into the layered structure and thus degrading the performance. The spinel coating also appears to increase Co 3+ segregation on the particle surface. Compared to the original material, the optimized sample demonstrates 47 % higher capacity retention at 3C and retains 89 % of initial capacity after 150 cycles at 0.5C. Besides, the specific energy density of 523 Wh kg -1 can be attained after 150 cycles at 0.5C. Moreover, the post-cycling analysis of modified sample verifies a better structural integrity with less particle cracking. Altogether, this study portrays an alternative strategy to overcome the shortcomings of LMR cathode materials.

25 ENERGY STORAGE↗

Building a spontaneously formed and self-healing protective layer with an F-rich electrochemically active organic molecule for ultra-stable Li metal batteries

Additives in the electrolyte act as engineers in Li metal batteries. Inspired by the superior cycle performance of organic materials in half cells, tetrafluoro-1,4-benzoquinone (TFBQ), the main structure of which has been widely applied as an organic cathode material, is utilized for the first time as an additive for Li metal protection. By chemical and electrochemical reactions between TFBQ and the Li metal surface, an F-rich interface layer is in situ formed on the Li metal surface during the charge and discharge process. From electrochemical tests and characterization, the powerful self-healing ability of the interface layer enabled by TFBQ is revealed, making an extremely stable Li metal anode. By using a lean electrolyte with 0.1 M TFBQ, the cycle life of Li|Li symmetric cells is increased at least 6 times compared to the control group. Moreover, impressive full cell performance was achieved. Ultra-stable Li–LFP cells showed a 0.026% average degradation for 600 cycles at 1C and Li–NMC622 cells showed a 36.8% higher capacity compared to the control group over 200 cycles at 0.5C, which are among the best results reported. Furthermore, this work efficiently and conveniently provides a new research direction to Li metal protection and Li metal batteries.

25 ENERGY STORAGE↗

Valence Effects of Fe Impurity for Recovered LiNi 0.6 Co 0.2 Mn 0.2 O 2 Cathode Materials

Iron impurities are generally included in the obtained leaching liquor solution during the hydrometallurgical recycling method of spent lithium-ion batteries (LIBs) due to the usage of iron in battery casings and machinery parts of recycling equipment, which would definitely affect the physical and electrochemical features of the recovered active materials. In this paper, the effects of iron impurity with different valence states (Fe 2+ and Fe 3+ ) and gradient concentrations (0.2, 1.0, and 5.0 at. %) for the obtained LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) cathodes are fully studied. It is found that Fe3+ impurity could easily lower the tap density and average size of NCM622 particles and even introduce some impurity phases in the NCM622 structure at high concentration (5.0 at. %), leading to much lower specific capacity, worse rate capability, and cycling performance of the Fe 3+ -based NCM622 cathode. On contrast, with certain concentrations of Fe 2+ impurity (0.2 and 1.0 at. %), the NCM622 cathode material exhibits comparable and much better electrochemical properties compared with the virgin NCM622 materials. Based on these results, the valence of Fe impurity should be considered and controlled as well as its concentration during the recycling process design for spent LIBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A universal etching method for synthesizing high-performance single crystal cathode materials

LiNi x MnyCo 1-x-y O 2 (NMC) is considered the most appealing cathode material due to its high energy density and low cost. However, the stability and safety concerns, caused by the degradation of polycrystalline cathode materials during cycling, have restricted their practical applications. To overcome this shortcoming, converting polycrystalline cathode to high-performance single-crystal cathode materials becomes an appealing solution. In this work, a universal etching approach is firstly developed to synthesize single-crystal cathode materials. The rate performance of the obtained single-crystal NMC111 is 10–15% more than that of polycrystalline NMC111 whereas the capacity retention of single-crystal NMC111 is enhanced by ~12% after 300 cycles at 0.5C. The obtained single-crystal NMC622 exhibits a pronounced improvement in rate performance, especially at high rates (~28.6% better at 5C and ~129% better at 10C) and has a comparable cycle performance compared to polycrystalline NMC622. Altogether, the findings propose an alternative approach to generate single-crystal particles with high energy density and cycle stability for the next generation lithium-ion batteries.

25 ENERGY STORAGE↗

Stabilized Lithium, Manganese-Rich Layered Cathode Materials Enabled by Integrating Co-Doping and Nanocoating

While lithium, manganese-rich (LMR) layered oxide cathode materials offer high energy density (>900 Wh kg –1 ) and low cost, LMR is susceptible to continuous capacity and voltage decay from the oxygen migration and side reaction with aqueous electrolyte at high voltage. Herein, the integration of Na/F co-doping (CD) and AlF 3 coating on LMR is achieved without the need of complex atomic layer deposition. Akin to pristine and CD samples, CD with 1 wt % AlF 3 (CD-1.0 wt %) shows excellent electrochemical performance with the capacity and voltage retentions of 93 and 91% after 150 cycles at 0.5C, respectively, and increased ionic conductivity. Spectroscopic analysis indicates that the coating mainly influences the Co distribution, where Co is enriched on the surface, and partial diffusion of Al 3+ ions toward the bulk, leading to a slight change of transition-metal (TM) valence states at the nanometer scale and the formation of a stable Li x (CoAl)O y phase. Post-cycling analysis reveals that CD-1.0 wt % can alleviate the formation of rock-salt structure and Mn dissolution. Besides, little to no metal segregation is detected for the cycled CD-1.0 wt % sample. This finding presents the first instance to apply co-doping and AlF 3 coating as a new strategy to enhance the structural homogeneity and takes another step toward their commercial viability.

25 ENERGY STORAGE↗

Understanding fundamental effects of Cu impurity in different forms for recovered LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathode materials

When identifying and developing lithium ion battery recycling technologies, understanding the role of impurities is always a concern as they may have an impact on electrochemical performance, material stability, or lifetime for recovered active materials. In this work we show that Cu impurity in different forms could play very different roles on the recovered LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622). Cu metal impurity could easily short the cell, while Cu ion impurity could play a positive role due to partially substitution of the Ni 2+ sites to lower the cation mixing degree. In specific, NCM622 material with certain amount (0.34 at%) of Cu ion impurity delivers high initial specific charge/discharge capacity of 211.8 and 186.0 mAh g -1 at 0.05 C, which are 12.2 and 14.1 mAh g -1 higher than those of virgin NCM622 cathode. Moreover, a superior retention capacity of 171.3 mAh g -1 after 90 cycles at 0.33 C, and striking rate capability are achieved in this NCM622 cathode sample. These results clearly indicate that Cu metal impurity should be avoided and the ionic Cu impurity should be controlled with optimal concentration during recycling process for spent LIBs.

25 ENERGY STORAGE↗

Systematic Study of Al Impurity for NCM622 Cathode Materials

Many recycling processes have been developed for spent Li-ion batteries (LIBs), such as pyrometallurgy, hydrometallurgy, and direct recycling. For all the recycling methods, however, impurities are always introduced from the current collectors or casing materials, especially aluminum (Al), which might lead to negative effects on recovered electrode materials. Therefore, it is significant to determine the impacts of Al impurity on recovered materials. Here, the influence of the Al impurity for the synthesized LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) precursor and cathode is systematically studied. The cell with 0.2 at % Al impurity displays the highest reversible capacities (145.2, 130.5, and 100.3 mAh g -1 from 2, 3, and 5 C, respectively) and striking cycling capability at 2 C after 100 cycles with the highest retention capacity of 138.5 mAh g -1 . Meanwhile, the excess Al ions (5 at %) lead to the Li/Mn superlattice structure and deteriorate electrochemical performance of the synthesized NCM622 cathode.

25 ENERGY STORAGE↗