Search NASA⌕ Search

Engineering topics

MacGowan, B. J. (ORCID:0000000310401900)

Publications and source records attributed to MacGowan, B. J. (ORCID:0000000310401900).

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Thermonuclear performance variability near ignition at the National Ignition Facility

We describe our current understanding of the variability and degradation mechanisms observed through a series of five indirectly driven inertial fusion implosions fielded at the National Ignition Facility in the fall of 2021, four of which attempted to reproduce the first experiment to achieve Lawson's criterion for ignition with a thermonuclear yield of 1.35 MJ on August 8, 2021. A large number of absolutely calibrated (imaging, time-resolved, and spectrally resolved) x-ray and neutron diagnostics are fielded on the NIF along multiple lines of sight for each experiment. This allows for a reconstruction of the DT fuel and ablator mix injected into the hotspot around peak burn. We show that nuclear yield variations are well reproduced by numerical modeling when the measured low mode asymmetries and mix mass are included. Furthermore, these observed perturbations during burn are linked to small variations in laser delivery and capsule defects. Stringent specifications are then set to achieve robust ignition with the implosion design studied in this paper.

Divol, L. (ORCID:0000000269699898)↗
DOE OSTI2024

The impact of low-mode symmetry on inertial fusion energy output in the burning plasma state

Indirect Drive Inertial Confinement Fusion Experiments on the National Ignition Facility (NIF) have achieved a burning plasma state with neutron yields exceeding 170 kJ, roughly 3 times the prior record and a necessary stage for igniting plasmas. The results are achieved despite multiple sources of degradations that lead to high variability in performance. Results shown here, for the first time, include an empirical correction factor for mode-2 asymmetry in the burning plasma regime in addition to previously determined corrections for radiative mix and mode-1. Analysis shows that including these three corrections alone accounts for the measured fusion performance variability in the two highest performing experimental campaigns on the NIF to within error. Here we quantify the performance sensitivity to mode-2 symmetry in the burning plasma regime and apply the results, in the form of an empirical correction to a 1D performance model. Furthermore, we find the sensitivity to mode-2 determined through a series of integrated 2D radiation hydrodynamic simulations to be consistent with the experimentally determined sensitivity only when including alpha-heating.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Design of inertial fusion implosions reaching the burning plasma regime

Abstract In a burning plasma state 1–7 , alpha particles from deuterium–tritium fusion reactions redeposit their energy and are the dominant source of heating. This state has recently been achieved at the US National Ignition Facility 8 using indirect-drive inertial-confinement fusion. Our experiments use a laser-generated radiation-filled cavity (a hohlraum) to spherically implode capsules containing deuterium and tritium fuel in a central hot spot where the fusion reactions occur. We have developed more efficient hohlraums to implode larger fusion targets compared with previous experiments 9,10 . This delivered more energy to the hot spot, whereas other parameters were optimized to maintain the high pressures required for inertial-confinement fusion. We also report improvements in implosion symmetry control by moving energy between the laser beams 11–16 and designing advanced hohlraum geometry 17 that allows for these larger implosions to be driven at the present laser energy and power capability of the National Ignition Facility. These design changes resulted in fusion powers of 1.5 petawatts, greater than the input power of the laser, and 170 kJ of fusion energy 18,19 . Radiation hydrodynamics simulations 20,21 show energy deposition by alpha particles as the dominant term in the hot-spot energy balance, indicative of a burning plasma state.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Burning plasma achieved in inertial fusion

Obtaining a burning plasma is a critical step towards self-sustaining fusion energy. A burning plasma is one in which the fusion reactions themselves are the primary source of heating in the plasma, which is necessary to sustain and propagate the burn, enabling high energy gain. After decades of fusion research, here we achieve a burning-plasma state in the laboratory. These experiments were conducted at the US National Ignition Facility, a laser facility delivering up to 1.9 megajoules of energy in pulses with peak powers up to 500 terawatts. We use the lasers to generate X-rays in a radiation cavity to indirectly drive a fuel-containing capsule via the X-ray ablation pressure, which results in the implosion process compressing and heating the fuel via mechanical work. The burning-plasma state was created using a strategy to increase the spatial scale of the capsule through two different implosion concepts. These experiments show fusion self-heating in excess of the mechanical work injected into the implosions, satisfying several burning-plasma metrics. Additionally, we describe a subset of experiments that appear to have crossed the static self-heating boundary, where fusion heating surpasses the energy losses from radiation and conduction. These results provide an opportunity to study α-particle-dominated plasmas and burning-plasma physics in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Fuel convergence sensitivity in indirect drive implosions

In inertial confinement fusion experiments at the National Ignition Facility, a spherical shell of deuterium–tritium fuel is imploded in an attempt to reach the conditions needed for fusion, self-heating, and eventual ignition. Since theory and simulations indicate that ignition efficacy in 1D improves with increasing imploded fuel convergence ratio, it is useful to understand the sensitivity of the scale-invariant fuel convergence on all measurable or inferable 1D parameters. In this paper, we develop a simple isobaric and isentropic compression scaling model incorporating sensitivity to the in-flight adiabat inferred from shock strengths, to measured implosion velocity, and to known initial ablator and fuel aspect ratio and mass ratio. The model is first benchmarked to 1D implosion simulations spanning a variety of relevant implosion designs. We then use the model to compare compressibility trends across all existing indirect-drive layered implosion data from the facility spanning three ablators [CH, carbon (C), and Be], for which in-flight fuel adiabats varied from 1.6 to 5 by varying the number of drive shocks from 2 to 4, peak implosion velocities varied by 1.4×, capsule radii by 50%, and initial fuel aspect ratios by 1.4×. We find that the strength of the first shock is the dominant contributor setting the maximum fuel convergence. We also observe additional sensitivities to successive shock strengths and fuel aspect ratios that improve the agreement between the expected and measured compression for carbon and Be designs with adiabats above 3. A principal finding is that the adiabat 2.5 C-shell designs exhibit less convergence than CH-shell designs of similar inferred in-flight adiabat.

Landen, O. L. (ORCID:0000000214998217)↗