Search NASA⌕ Search

Engineering topics

Maciolek, R. B.

Publications and source records attributed to Maciolek, R. B..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Improved detectivity of pyroelectric detectors

High detectivity single-element SBN pyroelectric detectors were fabricated. The theory and technology developments related to improved detector performance were identified and formulated. Improved methods of material characterization, thinning, mounting, blackening and amplifier matching are discussed. Detectors with detectivities of 1.3 x 10 to the 9th power square root of Hz/watt at 1 Hz are reported. Factors limiting performance and recommendations for future work are discussed.

Marshall, D. E.↗
NASA NTRS1978

Growth, evaluation and modeling of silicon-on-ceramic solar cells

The silicon-on-ceramic (SOC) process uses inexpensive ceramic substrates to provide supported growth of silicon from the melt. The conditions for unidirectional solidification, the grain structure and other properties are quite similar to those of EFG silicon ribbon. Solar cells with interdigital electrodes have demonstrated AMl conversion efficiencies (active area) of 7.8% without AR coatings and 10.1% efficiencies with an AR coating of SiO. Mathematical modeling of the series resistance of cells shows the feasibility of making electrical contact to the base layer of the cell through slots in the substrate. However, series resistance in the base layer sets an upper limit on slot spacing for efficient cell performance.

Zook, J. D.↗
NASA NTRS1977

Dip-coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

The objective of this research program is to investigate the technical and economic feasibility of producing solar-cell-quality sheet silicon by coating one surface of carbonized ceramic substrates with a thin layer of large-grain polycrystalline silicon from the melt. The past quarter demonstrated significant progress in several areas. Seeded growth of silicon-on-ceramic (SOC) with an EFG ribbon seed was demonstrated. Different types of mullite were successfully coated with silicon. A new method of deriving minority carrier diffusion length, L sub n from spectral response measurements was evaluated. ECOMOD cost projections were found to be in good agreement with the interim SAMIS method proposed by JPL. On the less positive side, there was a decrease in cell performance which we believe to be due to an unidentified source of impurities.

Zook, J. D.↗
NASA NTRS1976

Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

The technical and economic feasibility of producing solar cell quality sheet silicon by dip-coating one surface of carbonized ceramic substrates with a thin layer of large grain polycrystalline silicon was investigated. The dip-coating methods studied were directed toward a minimum cost process with the ultimate objective of producing solar cells with a conversion efficiency of 10% or greater. The technique shows excellent promise for low cost, labor-saving, scale-up potentialities and would provide an end product of sheet silicon with a rigid and strong supportive backing. An experimental dip-coating facility was designed and constructed, several substrates were successfully dip-coated with areas as large as 25 sq cm and thicknesses of 12 micron to 250 micron. There appears to be no serious limitation on the area of a substrate that could be coated. Of the various substrate materials dip-coated, mullite appears to best satisfy the requirement of the program. An inexpensive process was developed for producing mullite in the desired geometry.

Heaps, J. D.↗
NASA NTRS1976

Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

To date, an experimental dip-coating facility was constructed. Using this facility, relatively thin (1 mm) mullite and alumina substrates were successfully dip-coated with 2.5 - 3.0 ohm-cm, p-type silicon with areas of approximately 20 sq cm. The thickness and grain size of these coatings are influenced by the temperature of the melt and the rate at which the substrate is pulled from the melt. One mullite substrate had dendrite-like crystallites of the order of 1 mm wide and 1 to 2 cm long. Their axes were aligned along the direction of pulling. A large variety of substrate materials were purchased or developed enabling the program to commence a substrate definition evaluation. Due to the insulating nature of the substrate, the bottom layer of the p-n junction may have to be made via the top surface. The feasibility of accomplishing this was demonstrated using single crystal wafers.

Heaps, J. D.↗
NASA NTRS1976

Dip-coated sheet silicon solar cells

A cost-effective method is being developed for producing solar cell quality sheet silicon by dip coating inexpensive ceramic substrates with a thin layer of large grain silicon. Mullite (Aluminum Silicate) ceramic substrates coated with a thin layer of graphite have been dipped into molten silicon to produce 20-150 micron thick layers having grain sizes as large as .4 cm x 4 cm. With these silicon layers photovoltaic diodes have been fabricated with measured and inherent conversion efficiencies of 4% and 7%, respectively.

Heaps, J. D.↗
NASA NTRS1975

Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

The research program to investigate the technical and economic feasibility of producing solar-cell-quality sheet silicon by dip-coating one surface of carbonized ceramic substrates with a thin layer of large-grain polycrystalline silicon is reported. The initial effort concentrated on the design and construction of the experimental dip-coating facility. The design was completed and its experimental features are discussed. Current status of the program is reported, including progress toward solar cell junction diffusion and miscellaneous ceramic substrate procurement.

Heaps, J. D.↗